02293nas a2200253   4500008004100000022001400041245009300055210006900148260013000217300001200347490000700359520135300366653001101719653004001730653001901770653001401789653001801803100002201821700001901843700001801862700002201880700002001902856011701922       2006                        eng d  a1226-086X00aDielectric properties of BaTiO3 ceramics prepared from powders with bimodal distribution0 aDielectric properties of BaTiO3 ceramics prepared from powders w  aA-803 TWIN BLDG, 275-3, YANGJAE-DONG, SEOCHO-KU, SEOUL 137-130, SOUTH KOREAbKOREAN SOC INDUSTRIAL ENGINEERING CHEMISTRYcJUL  a584-5880 v123 a<p>BaTiO3 (BT) powders having bimodal distribution were synthesized successfully through a simple classical solid-state reaction route using cheap BaCO3 and TiO2 as starting materials. These powders were further processed in the form of green pellets to obtain dense BT ceramics having densities of similar to 94 similar to 96 % after sintering in air at 1350 and 1400 degrees C/4 h in air. The room temperature dielectric constant (epsilon(RT)) of similar to 1500 at 1 KHz frequency was increased to : 10000 at a Curie temperature (T-C) similar to 126 degrees C, showing a very sharp transition from a polar tetragonal to a non-polar cubic structure. The dielectric loss factor (tan 6) was similar to 1.5 %. SEM studies revealed the presence of dense microstructures having a distribution of smaller grains (size: 2 similar to 3 gm) surrounded by larger grains (&gt;= 35 mu m). The ferroelectric hysteresis loop measurements on these samples gave values of spontaneous polarization (P-s) of similar to 12.0 mu C/cm(2), a coercive field (E-C) of similar to 2 similar to 2.5 kV/cm, and a dielectric strength (E-b) of similar to 48.0 kV/cm. DC-resistivity as high as 1.5 x 10(9) Omega-cm was obtained in these samples. All these results are quite comparable with reported ferroelectric/dielectric data and are discussed elaborately in this paper.</p>10aBaTiO310adielectric-ferroelectric properties10aMicrostructure10aSintering10astoichiometry1 aDeshpande, S., B.1 aPotdar, H., S.1 aPatil, M., M.1 aDeshpande, V., V.1 aKhollam, Y., B.  uhttps://library.ncl.res.in/content/dielectric-properties-batio3-ceramics-prepared-powders-bimodal-distribution-002476nas a2200277   4500008004100000022001400041245012400055210006900179260000800248300001100256490000800267520158800275653001101863653002001874653001401894653001501908653001801923653000901941100001501950700001601965700001701981700002201998700003102020700002102051856012602072       2020                        eng d  a0925-838800aPVDF/BaTiO3 films with nanocellulose impregnation: investigation of structural, morphological and mechanical properties0 aPVDFBaTiO3 films with nanocellulose impregnation investigation o  cMAY  a1537010 v8233 a<p>Polyvinylidene fluoride (PVDF) composite films have witnessed widespread applications in biomedical and flexible electronic devices in recent years. These applications require a material that has enhanced electrical properties, mechanical flexibility along with sufficient strength. A lot of research has been carried out to enhance the piezoelectric and dielectric properties of the PVDF composite films. However, the improvements in the mechanical properties of nano filler reinforced PVDF composite films has not received due attention. In this regard, the present work focuses towards enhancing the mechanical strength and load-bearing capability of PVDF, by preparing composites of PVDF films impregnated with Cellulose Nanocrystals (CNC) and Barium Titanate (BTO) nanoparticles. Solution casting method was adapted to fabricate the PVDF/BTO/CNC films. X-ray diffractograms and FTIR (Fourier Transform infrared spectroscopy) corroborate the presence of ferroelectric gamma phase in PVDF. Mechanical and viscoelastic measurements have been carried out to examine the influence of CNC and BTO nano fillers in the PVDF matrix. The addition of CNC and BTO in PVDF film has improved the mechanical strength significantly. The stress achieved for PVDF/5% BTO and PVDF/5% BTO with 0.9% of CNC at 5% strain was 17% and 130% higher than the pristine PVDF, respectively. This study can be helpful for the design engineers to meet custom/specific requirements for a myriad of end- user applications such as piezoelectric nanogenerators. (C) 2020 Elsevier B.V. All rights reserved.</p>
10aBaTiO310aComposite films10aMechanics10aMorphology10aNanocellulose10aPVDF1 aRam, Farsa1 aKaviraj, P.1 aPramanik, R.1 aKrishnan, Amrutha1 aShanmuganathan, Kadhiravan1 aArockiarajan, A.  uhttps://library.ncl.res.in/content/pvdfbatio3-films-nanocellulose-impregnation-investigation-structural-morphological-and