02230nas a2200217   4500008004100000022001400041245010100055210006900156260000900225490000700234520148200241653001601723653001301739653001901752653001901771653001701790100002301807700002501830700003001855856012701885       2023                        eng d  a2196-021600aLinear polymer comprising dual functionalities with hierarchical pores for lithium ion batteries0 aLinear polymer comprising dual functionalities with hierarchical  cOCT 0 v103 a<p>Organic materials with carbonyl, azo, nitrile and imine moieties are widely used in lithium batteries. The solubility of these materials in battery electrolytes is an issue. Aggregation of the organic molecules can suppress the solubility, but the accessibility of lithium-ion is hindered. Therefore, insoluble porous organic materials are desired. Herein, we synthesized a linear polymer with carbonyl and azo functionalities. Due to the presence of easily isomerizable azo moiety, a porous polymer was obtained. The polymer showed nano and micropores. The battery with the porous polymer showed an impressive specific capacity of 400 mA h/g at 0.2 A/g. If the battery is pre-conditioned, the specific capacity increased to 615 mA h/g at the same current density. The post-mortem analysis of the battery confirmed that the polymer didn't dissolve in the battery electrolyte. The control material is a small molecule with carbonyl and azo moieties that showed a poor specific capacity of 40 mA h/g indicating the necessity to have a hierarchically porous dual-functional polymer. Polymers for batteries: A linear polymer with micro and Nano pores with azo and carbonyl functionalities renders increased accessibility to Li ions after preconditioning. During charge-discharge experiment Azo-Carb-PDI electrode had impressive discharge capacity of 469 mA h/g after 500 cycle which is almost 15 times higher than the monomer (Azo-PDI-Azo, 30 mA h/g after 100 cycle).image</p>
10aazo polymer10acarbonyl10aLi-ion battery10aporous polymer10aRylene-imide1 aAher, Jagadish, D.1 aPalani, Sathishkumar1 aKrishnamoorthy, Kothandam  uhttps://library.ncl.res.in/content/linear-polymer-comprising-dual-functionalities-hierarchical-pores-lithium-ion-batteries02974nas a2200253   4500008004100000022001400041245015100055210006900206260000800275300001400283490000600297520205900303653001902362653002502381653001302406653001902419653002102438100002402459700002902483700002002512700002602532700003002558856013202588       2025                        eng d  a2637-610500aLong cycling stability imparted to li-ion batteries by conjugated polymers with low dihedral angles and high electron density on functional groups0 aLong cycling stability imparted to liion batteries by conjugated  cJUN  a7719-77280 v73 a<p>
	In conjugated polymers, dihedral angles at bonds connecting their monomers impact the polymers' properties such as the packing of the polymer chains, bandgap, and conductivity. These properties are expected to impact the performance of rechargeable Li-ion batteries because the Li-ion transport and conductivity of the polymers are two important parameters. To understand this, we designed and synthesized two polymers with two different dihedral angles. The polymer, Poly(EDOT-DPP), comprising diketopyrrolopyrrole (DPP) and ethylenedioxythiophene (EDOT) as monomers, showed a low dihedral angle of 2 degrees. On the other hand, the polymer, Poly(EDOT-i-Ind), comprising EDOT and i-Indigo (i-Ind) showed a dihedral angle of 17 degrees. Density functional theory (DFT) studies showed that the electron density at the carbonyl moiety of EDOT-DPP is higher than that of EDOT-i-Ind. This resulted in a higher Li+ binding energy of -3.665 eV for EDOT-DPP and a lower Li+ binding energy of -3.464 eV for EDOT-i-Ind. Battery electrodes were fabricated using either Poly(EDOT-DPP) or Poly(EDOT-i-Ind) with multiwalled carbon nanotubes as conducting fillers in the absence of any binders. The Li+ ion diffusion coefficient ( D Li + ) measured for the as prepared batteries based on Poly(EDOT-DPP) was found to be 3.9 x 10-19 cm2/s, which is slightly higher than that found for Poly(EDOT-i-Ind). However, after 2000 cycles, the D Li + increased by about two orders of magnitude for both polymers. Due to the low dihedral angle in the case of Poly(EDOT-DPP), the D Li + was found to be 21% higher than that of Poly(EDOT-i-Ind). The higher binding of Li+ ions with Poly(EDOT-DPP) and Li+ ion diffusion improved the specific capacity and cycling performance of batteries fabricated with this polymer. At a current density of 0.2 A/g, Poly(EDOT-DPP) showed a 39% higher specific capacity than the Poly(EDOT-i-Ind) polymer after 2000 cycles. The batteries also showed stable performance over 2000 cycles with an insignificant decrease in specific capacity.</p>
10adihedral angle10adiketopyrrolopyrrole10ai-indigo10aLi-ion battery10aLi-ion transport1 aKargude, Radhakisan1 aSrinivasalu, Hari, Haran1 aDevasia, George1 aKrishnamurty, Sailaja1 aKrishnamoorthy, Kothandam  uhttps://library.ncl.res.in/content/long-cycling-stability-imparted-li-ion-batteries-conjugated-polymers-low-dihedral-angles-and