03106nas a2200241   4500008004100000022001400041245014800055210006900203260000900272300001600281490000700297520225700304653002402561653003102585653000802616653001002624653002102634653001602655100002102671700001802692700002402710856013002734       2023                        eng d  a1944-824400aMicroporous 3D-structured hierarchically entangled graphene-supported Pt3Co alloy catalyst for PEMFC application with process-friendly features0 aMicroporous 3Dstructured hierarchically entangled graphenesuppor  cJUN   a28023-280350 v153 a<p>
	To improve the oxygen reduction reaction(ORR) performance in aproton-exchange membrane fuel cell (PEMFC) cathode with respect tomass activity and durability, a suitable electrocatalyst design strategyis essentially needed. Here, we have prepared a sub-three nm-sizedplatinum (Pt)-cobalt (Co) alloy (Pt3Co)-supportedN-doped microporous 3D graphene (Pt3Co/pNEGF) by usingthe polyol synthesis method. A microwave-assisted synthesis methodwas employed to prepare the catalyst based on the 3D porous carbonsupport with a large pore volume and dense micro-/mesoporous surfaces.The ORR performance of Pt3Co/pNEGF closely matches withthe state-of-the-art commercial Pt/C catalyst in0.1 M HClO4, with a small overpotential of 10 mV. The 3Dmicroporous structure of the N-doped graphene significantly improvesthe mass transport of the reactant and thus the overall ORR performance.As a result of the lower loading of Pt in Pt3Co/pNEGF ascompared to that in Pt/C, the alloy catalyst achieved 1.5 times highermass activity than Pt/C. After 10,000 cycles, the difference in theelectrochemically active surface area (ECSA) and half-wave potential(E (1/2)) of Pt3Co/pNEGF is foundto be 5 m(2) g(Pt) (-1) (Delta ECSA)and 24 mV (Delta E (1/2)), whereas, forPt/C, these values are 9 m(2) g(Pt) (-1) and 32 mV, respectively. Finally, in a realistic perspective, single-celltesting of a membrane electrode assembly (MEA) was made by sandwichingthe Pt3Co/pNEGF-coated gas diffusion layers as the cathodedisplayed a maximum power density of 800 mW cm(-2) under H-2-O-2 feed conditions with aclear indication of helping the system in the mass-transfer region(i.e., the high current dragging condition). The nature of the I-V polarization shows a progressivelylower slope in this region of the polarization plot compared to asimilar system made from its Pt/C counterpart and a significantlyimproved performance throughout the polarization region in the caseof the system made from the Pt3Co/NEGF catalyst (withoutthe microwave treatment) counterpart. These results validate the betterprocess friendliness of Pt3Co/pNEGF as a PEMFC electrode-specificcatalyst owing to its unique texture with 3D architecture and well-definedporosity with better structural endurance.</p>
10amicrowave synthesis10aN-doped porous 3D graphene10aORR10aPEMFC10apolyol synthesis10aPt3Co alloy1 aManna, Narugopal1 aSingh, Mayank1 aKurungot, Sreekumar  uhttps://library.ncl.res.in/content/microporous-3d-structured-hierarchically-entangled-graphene-supported-pt3co-alloy-catalyst02589nas a2200325   4500008004100000022001400041245014000055210006900195260000800264490000700272520142200279653002001701653001901721653002801740653002801768653003001796653003901826653001601865653001801881653005001899100002201949700002401971700002701995700002402022700001802046700002602064700001802090700002402108856013102132       2025                        eng d  a1613-681000aHot injection assisted electronically modulated twin and grain boundary rich sub-2 nm pt3co alloy resistant to phosphate ion for PEMFCs0 aHot injection assisted electronically modulated twin and grain b  cMAY0 v213 a<p>
	Modulation of the electronic d-band center, structural defects (line defects), and particle size of Pt3Co alloy electrocatalyst have huge significance in elevating its electrochemical oxygen reduction reaction activity. Deviating from traditional high-temperature strategies, the current work focuses on ripening these benefits by implying a simple economically viable hot-injection-assisted modified polyol process. A conclusive control over decrementing particle size starting from 2.7 to 1.3 nm, an increasing degree of strain (twin boundary), and shifting of the d-band center away from the Fermi level are obtained via varying the temperature to which the solution is injected. The catalyst prepared via the injection at 200 degrees C (Pt3Co(1.3 t,g-b)/fVC-200) has delivered an electrochemical surface area of 84 m(2) g(Pt)(-1) with the onset and half-wave potentials of 0.980 and 0.858 V, respectively, versus RHE and a limiting current of -6.0 mA cm(-2) with stability till 20k cycles. In the high-temperature proton exchange membrane fuel cell Pt3Co(1.3 t,g-b)/fVC-200-based cell has outperformed Pt/C rendering 600 mWcm(-2) under H-2-Air compared to 529 mWcm(-2) of Pt/C with 20% lower Pt loading and double the stability due to enhanced resistance toward phosphoric acid for accelerated voltage cycling. A similar enhancement is seen while employing the catalyst for low-temperature fuel cells.</p>
10aelectrocatalyst10agrain boundary10ahot injection synthesis10amodified polyol process10aoxygen reduction reaction10aproton exchange membrane fuel cell10aPt3Co alloy10atwin boundary10avalance band X-ray photoelectron spectroscopy1 aSingh, Mayank, U.1 aJadhav, Swapnil, D.1 aShivankar, Bhavana, R.1 aPandikassala, Ajmal1 aKumar, Yogesh1 aKrishnamurty, Sailaja1 aVinod, C., P.1 aKurungot, Sreekumar  uhttps://library.ncl.res.in/content/hot-injection-assisted-electronically-modulated-twin-and-grain-boundary-rich-sub-2-nm-pt3co