01469nas a2200241   4500008004100000022001400041245005000055210005000105260007300155300001400228490000700242520071400249653002300963653002400986653002501010653001801035100001301053700002301066700002001089700002101109700001301130856008401143       2006                        eng d  a0167-577X00aChemical methods to synthesize FeTiO3 powders0 aChemical methods to synthesize FeTiO3 powders  aPO BOX 211, 1000 AE AMSTERDAM, NETHERLANDSbELSEVIER SCIENCE BVcMAY  a1425-14270 v603 a<p>Three different techniques were used to synthesize FeTiO3 powders. The first method is simple coprecipitation of both Fe and Ti ions under basic conditions using standard ammonia solution from aqueous ferric nitrate and titanium oxy chloride. This precipitate on heating at 400 degrees C produces ilmenite phase. The second method is to digest hydroxide precipitates at 100 degrees C to form FeTiO3 phase. The third technique is to make use of citrate process to form FeTiO3 powders. The phase contents and lattice parameters were Studied by powder X-ray diffraction (XRD). Particle size and morphology were studied by Transmission Electron Microscopy (TEM). (c) 2005 Elsevier B.V. All tights reserved.</p>10aChemical synthesis10aElectron microscopy10aelectronic materials10aX-ray methods1 aMona, J.1 aKale, Sangeeta, N.1 aGaikwad, A., B.1 aMurugan, Vadivel1 aRavi, V.  uhttps://library.ncl.res.in/content/chemical-methods-synthesize-fetio3-powders-001365nas a2200217   4500008004100000022001400041245005600055210005600111260007300167300001400240490000700254520066500261653001300926653002400939653002500963653002200988100001501010700002001025700001201045856009001057       2006                        eng d  a0167-577X00aCoprecipitation technique to prepare LiTaO3 powders0 aCoprecipitation technique to prepare LiTaO3 powders  aPO BOX 211, 1000 AE AMSTERDAM, NETHERLANDSbELSEVIER SCIENCE BVcAPR  a1047-10480 v603 a<p>A simple coprecipitation technique had been successfully applied for the preparation of pure ultrafine single phase LiTaO3 (LT). An aqueous mixture of ammonium carbonate and ammonium hydroxide was used to precipitate Li+ and Ta5+ cations as carbonate and hydroxide respectively. This precursor oil heating at 750 degrees C produces LT powders. For comparison, LT powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM). (c) 2005 Elsevier B.V. All rights reserved.</p>10aCeramics10aElectron microscopy10aelectronic materials10aX-ray diffraction1 aNavale, SC1 aGaikwad, A., B.1 aRavi, V  uhttps://library.ncl.res.in/content/coprecipitation-technique-prepare-litao3-powders-001483nas a2200241   4500008004100000022001400041245005900055210005900114260010500173300001200278490000700290520069100297653001300988653002301001653002401024653002501048653001101073653001801084100001401102700002001116700001201136856009301148       2006                        eng d  a0250-470700aCoprecipitation technique to prepare NaNbO3 and NaTaO30 aCoprecipitation technique to prepare NaNbO3 and NaTaO3  aC V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIAbINDIAN ACADEMY SCIENCEScAPR  a123-1250 v293 a<p>A simple coprecipitation technique has been used successfully for the preparation of pure, ultrafine, single phases of NaNbO3 (NN) and NaTaO3 (NT). An alcoholic solution of ammonium carbonate and ammonium hydroxide was used to precipitate Na+ and Nb5+ (or Ta5+) cations under basic conditions as carbonate and hydroxide, respectively. On heating at 700 degrees C, these precursors produce respective products. For comparison, both NN and NT powders were also prepared by the traditional solid state method. The phase purity and lattice parameters were studied by powder X-ray diffraction (XRD). The particle size and morphology were studied by scanning electron microscopy (SEM).</p>10aCeramics10aChemical synthesis10aElectron microscopy10aelectronic materials10aOxides10aX-ray methods1 aSamuel, V1 aGaikwad, A., B.1 aRavi, V  uhttps://library.ncl.res.in/content/coprecipitation-technique-prepare-nanbo3-and-natao3-001492nas a2200241   4500008004100000022001400041245005700055210005500112260010500167300001200272490000700284520071000291653001301001653002401014653002101038653001101059653002201070100002101092700002001113700001501133700001301148856008901161       2006                        eng d  a0250-470700aCoprecipitation technique to prepare Sr0.5Ba0.5Nb2O60 aCoprecipitation technique to prepare Sr05Ba05Nb2O6  aC V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIAbINDIAN ACADEMY SCIENCEScJUN  a221-2230 v293 a<p>An aqueous mixture of ammonium oxalate and ammonium hydroxide was used to coprecipitate barium and strontium ions as oxalates and niobium ions as hydroxide under basic conditions. This precursor on calcining at 750 degrees C yielded Sr0.5Ba0.5Nb2O6 phase. This is a much lower temperature than that prepared by traditional solid state method (1000 degrees C) as reported for the formation of Sr0.5Ba0.5Nb2O6 (SBN). Transmission electron microscopic (TEM) investigations revealed that the average particle size was 80 nm for the calcined powders. The room temperature dielectric constant at I kHz was found to be 1100. The ferroelectric hysteresis loop parameters of these samples were also studied.</p>10aCeramics10aElectron microscopy10aferroelectricity10aOxides10aX-ray diffraction1 aMurugan, Vadivel1 aGaikwad, A., B.1 aSamuel, V.1 aRavi, V.  uhttps://library.ncl.res.in/content/coprecipitation-technique-prepare-sr05ba05nb2o6-001439nas a2200241   4500008004100000022001400041245005000055210004900105260009900154300001200253490000700265520067900272653002100951653001300972653002400985653001101009653002201020100001901042700001901061700002001080700001301100856008401113       2007                        eng d  a0272-884200aCo-precipitation technique to prepare BaTa2O60 aCoprecipitation technique to prepare BaTa2O6  aTHE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLANDbELSEVIER SCI LTDcJAN  a297-2990 v333 a<p>A mixture of ammonium oxalate and ammonium hydroxide was used to co-precipitate barium and tantalum ions as barium oxalate and tantalum hydroxide under basic conditions. On calcination at 750 degrees C, this precursor yielded BaTa2O6 (BT) ceramics. This is much lower temperature as compared to that prepared by traditional solid-state method (1000 degrees C) as reported for the formation of BaTa206. Transmission electron microscope (TEM) investigations revealed that the average particle size is 70 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 100. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.</p>10abarium tantalate10aCeramics10aElectron microscopy10aOxides10aX-ray diffraction1 aNavale, S., C.1 aSamuel, Violet1 aGaikwad, A., B.1 aRavi, V.  uhttps://library.ncl.res.in/content/co-precipitation-technique-prepare-bata2o6-001466nas a2200253   4500008004100000022001400041245006100055210006100116260007300177300001400250490000700264520066400271653002300935653002500958653001100983653001800994100002201012700001801034700002001052700001501072700001901087700001301106856009301119       2007                        eng d  a0167-577X00aCoprecipitation technique to prepare CoTa2O6 and CoNb2O60 aCoprecipitation technique to prepare CoTa2O6 and CoNb2O6  aPO BOX 211, 1000 AE AMSTERDAM, NETHERLANDSbELSEVIER SCIENCE BVcMAY  a2127-21290 v613 a<p>An aqueous solution of sodium hydroxide was used to coprecipitate cobalt and tantalum (or niobium) ions from their precursors as hydroxides under basic conditions. This precipitate yielded CoTa2O6 (CT) or CoNb2O6 (CN) ceramics on calcining at 700 degrees C, i.e. at a temperature much lower than 900 degrees C, reported for the formation of these powders prepared by the traditional solid state method. The X-ray diffraction (XRD) studies were employed to investigate phase contents and lattice parameters. The morphology of the synthesized powders was investigated by transmission electron microscopy (TEM). (c) 2006 Elsevier B.V. All rights reserved.</p>10aChemical synthesis10aelectronic materials10aOxides10aX-ray methods1 aMulla, Imtiaz, S.1 aNatarajan, N.1 aGaikwad, A., B.1 aSamuel, V.1 aGuptha, U., N.1 aRavi, V.  uhttps://library.ncl.res.in/content/coprecipitation-technique-prepare-cota2o6-and-conb2o601333nas a2200253   4500008004100000022001400041245004900055210004900104260007300153300001400226490000700240520056500247653002300812653002400835653002500859653001100884653001800895100001500913700002000928700001900948700001800967700001300985856008100998       2007                        eng d  a0167-577X00aCoprecipitation technique to prepare NiNb2O60 aCoprecipitation technique to prepare NiNb2O6  aPO BOX 211, 1000 AE AMSTERDAM, NETHERLANDSbELSEVIER SCIENCE BVcMAY  a2354-23550 v613 a<p>A mixture of ammonium carbonate and ammonium hydroxide was used to coprecipitate nickel and niobium ions as nickel carbonate and niobium hydroxide under basic conditions. This precursor yielded NiNb2O6 (NN) ceramics on calcining at 700 degrees C (at a temperature lower than 800 degrees C which is necessary for the formation of NiNb2O6 when prepared by the traditional solid state method). The average particle size and morphology of these powders were investigated by transmission electron microscope (TEM). (c) 2006 Elsevier B.V. All rights reserved.</p>10aChemical synthesis10aElectron microscopy10aelectronic materials10aOxides10aX-ray methods1 aSamuel, V.1 aGaikwad, A., B.1 aJadhav, A., D.1 aNatarajan, N.1 aRavi, V.  uhttps://library.ncl.res.in/content/coprecipitation-technique-prepare-ninb2o602230nas a2200229   4500008004100000022001400041245011800055210006900173260010600242300001400348490000700362520131900369653002301688653001101711653003301722653002301755653003701778100001801815700002001833700001801853856012901871       2007                        eng d  a0013-468600aCorrosion protection aspects of electrochemically synthesized poly(o-anisidine-co-o-toluidine) coatings on copper0 aCorrosion protection aspects of electrochemically synthesized po  aTHE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLANDbPERGAMON-ELSEVIER SCIENCE LTDcMAY  a5958-59670 v523 a<p>The poly(o-anisidine-co-o-toluidine) coatings were synthesized on copper substrates by electrochemical copolymerization of o-anisidine with o-toluidine using sodium salicylate as supporting electrolyte. These coatings were characterized by cyclic voltammetry, UV-vis absorption spectroscopy, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and scanning electron microscopy (SEM). The formation of the copolymer with the mixture of monomers in the aqueous sodium salicylate solution was ascertained by a critical comparison of the results obtained with the polymerization of the individual monomers, o-anisidine and o-toluidine, respectively. The corrosion protection aspects of poly(o-anisidine-co-o-toluidine) coatings to copper was investigated in aqueous 3% NaCl solution by potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The results of the potentiodynamic polarization measurements and EIS studies showed that the poly(o-anisidine-co-o-toluidine) coatings provided the effective corrosion protection to copper than that of respective homopolymers. The corrosion rate is observed to depend on the feed ratio of o-toluidine used for the synthesis of the copolymer coatings. (C) 2007 Elsevier Ltd. All rights reserved.</p>10acopolymer coatings10aCopper10aCorrosion resistant coatings10acyclic voltammetry10apoly(o-anisidine-co-o-toluidine)1 aPawar, Pritee1 aGaikwad, A., B.1 aPatil, P., P.  uhttps://library.ncl.res.in/content/corrosion-protection-aspects-electrochemically-synthesized-polyo-anisidine-co-o-toluidine