02650nas a2200217   4500008004100000022001400041245012400055210006900179260000900248300001100257490000700268520187900275653001202154653003002166653001902196653002602215653001202241100002102253700002702274856013102301       2019                        eng d  a0022-372700aEffect of electrostatic interactions on structure and mechanical properties of ice templated colloid-polymer composites0 aEffect of electrostatic interactions on structure and mechanical  cMAY   a2140020 v523 a<p>When an aqueous dispersion of negatively charged colloids, cationic polymer and crosslinker is frozen and the polymer is allowed to crosslink in the frozen state, we obtain a self-standing macroporous composite foam. This material is soft, despite the high concentration of colloids and yet is remarkably elastic to large compressive strains. In these macroporous composites, the pore walls comprise colloidal particles held within a crosslinked polymer network. Here, we investigate the effect of varying colloid- polymer interactions in pre-fabricated macroporous composites on their microstructure and mechanical properties. During preparation of the composite, cationic polymer adsorbs on the negatively charged colloids. We tune the surface charge of particles embedded in a macroscopic monolith by immersing the composites in water maintained at different pH. In this way, we tune polymer-particle interactions in the composite. We observe a sudden increase in interparticle distance and swelling of composite when pH is decreased below the particle's isoelectric point. Correspondingly, we observe reduction in Young's and shear moduli, compression strength and macroscopic energy dissipation. We did not observe any pH dependent changes in pure polymer sponges (prepared by ice templating and crosslinking a polymer solution that does not contain colloidal particles). Therefore, the pH dependent structural and mechanical property changes arise from the composite structure rather than purely from the crosslinked polymer. We believe that the reduction in mechanical stiffness when the polymer-particle interaction becomes repulsive is because of the reduction in interfacial contacts between particle and polymer. Therefore, the mechanical stiffness of ice templated composite is strongly influenced by interactions between the polymer and particle surface.</p>10acolloid10aelectrostatic interaction10aice templating10amechanical properties10aPolymer1 aSuresh, Karthika1 aKumaraswamy, Guruswamy  uhttps://library.ncl.res.in/content/effect-electrostatic-interactions-structure-and-mechanical-properties-ice-templated-colloid02769nas a2200229   4500008004100000022001400041245013600055210006900191260000800260300001400268490000700282520195800289653002602247653001002273653002602283653001302309100001902322700002302341700002002364700002702384856012802411       2019                        eng d  a0969-023900aStructure-property relations in regenerated cellulose fibers: comparison of fibers manufactured using viscose and lyocell processes0 aStructureproperty relations in regenerated cellulose fibers comp  cAPR  a3655-36690 v263 a<p>Regenerated cellulose fibers are produced using two industrially dominant technologies: the viscose and lyocell processes. Here, we compare commercially available fibers, prepared using the viscose and lyocell processes. Single fibers are subjected to a variety of mechanical deformations to obtain stress-strain, stress relaxation and stress recovery data. These are fitted to a phenomenological model, whose parameters are interpreted in terms of the fiber semicrystalline microstructure. This simple model does not incorporate the complexities of semicrystalline microstructure. Rather, it represents structure in a semicrystalline polymer fiber in terms of an elastic crystalline phase that coexists with a viscoelastic Voigt-like glassy amorphous phase. Lyocell fibers are characterized by higher values of crystalline modulus relative to viscose. Lyocell fibers also have a higher amorphous phase modulus and a wider relaxation spectrum than viscose, suggesting that amorphous and crystalline phases are dispersed in close connectivity in lyocell. Viscose and lyocell fibers exhibit qualitative similarities in their mechanical response. On stretching, there is a transition in the stress-strain curve from a low strain elastic response at a critical value of strain. This critical strain has been incorrectly attributed to yielding of the fiber. We establish that this critical value corresponds to an apparent yield. When subjected to strains higher than this apparent yield point, the fibers develop a memory of the mechanical deformation. This memory decays slowly, logarithmically with time and is lost over about a day as the fiber structure transitions back to the original as spun fiber. Finally, we demonstrate that on wetting the fibers with water, there is an increase in the apparent yield strain for viscose fibers, but not for lyocell. We interpret these results in terms of the semicrystalline microstructure of the fibers.</p>
10amechanical properties10aModel10aRegenerated cellulose10aYielding1 aSharma, Aakash1 aNagarkar, Shailesh1 aThakre, Shirish1 aKumaraswamy, Guruswamy  uhttps://library.ncl.res.in/content/structure-property-relations-regenerated-cellulose-fibers-comparison-fibers-manufactured