02673nas a2200265   4500008004100000022001400041245012700055210006900182260000800251300001400259490000600273520174800279653002502027653002302052653002602075653001402101653001702115653003302132100001502165700002602180700002402206700002102230700003102251856012502282       2020                        eng d  a2574-096200aEnhancing thermomechanical and chemical stability of polymer electrolyte membranes using polydopamine coated nanocellulose0 aEnhancing thermomechanical and chemical stability of polymer ele  cFEB  a1988-19990 v33 a<p>We report here an approach to enhance the chemical and thermomechanical stability of polymer electrolyte membranes without compromising proton conductivity. Multifunctional polydopamine coated nanocellulose (PNC) was prepared by oxidative polymerization of dopamine on nano cellulose fibers and subsequently incorporated in Nafion by solution blending. PNC had a very significant effect on the thermomechanical properties of Nafion showing up to 200% improvement in the storage modulus at 90 degrees C. The PNC network also enhanced the dimensional stability of Nafion under constant stress. The 3 wt % PNC composite membrane showed a drastic reduction in creep compliance of about 39.9% and 46.5% in J(max) at 30 degrees and 60 degrees C, respectively. Free radical scavenging properties of polydopamine also helped to significantly enhance the chemical stability of Nafion, which was ascertained by accelerated degradation tests conducted in Fenton's reagent at 70 degrees C over 40 days. F-19 CP MAS solid state NMR, FTIR, and tensile tests on the membranes show higher chemical stability of the 3 wt % PNC composite membrane. The proton conductivity of the 3 wt % PNC composite membrane at 90 degrees C and 100% RH (similar to 125 mS/cm) was slightly higher than the Nafion membrane (similar to 94 mS/cm) at similar conditions. The retention of proton conductivity even with lower water uptake could be ascribed to proton hopping through polydopamine coated nanocellulose. Performance of the composite membrane was also evaluated in a single stack fuel cell and found to be better than recast Nafion. The benefits derived by this approach are not restricted to Nafion alone and shall broadly apply to many other polymer membranes.</p>
10acellulose nanofibers10achemical stability10adimensional stability10afuel cell10apolydopamine10apolymer electrolyte membrane1 aRam, Farsa1 aVelayutham, Parthiban1 aSahu, Akhila, Kumar1 aLele, Ashish, K.1 aShanmuganathan, Kadhiravan  uhttps://library.ncl.res.in/content/enhancing-thermomechanical-and-chemical-stability-polymer-electrolyte-membranes-using02152nas a2200253   4500008004100000022001400041245015200055210006900207260000800276300001400284490000700298520126500305653001201570653001601582653002701598653002201625653002101647100001501668700001801683700001701701700002701718700003101745856012201776       2021                        eng d  a0969-023900aElastic piezoelectric aerogels from isotropic and directionally ice-templated cellulose nanocrystals: comparison of structure and energy harvesting0 aElastic piezoelectric aerogels from isotropic and directionally   cJUL  a6323-63370 v283 a<p>We report the preparation of highly compressible and elastic piezoelectric aerogels of carboxylated cellulose nanocrystals (CNCs). Aqueous CNC dispersions containing polyethyleneimine and crosslinker were frozen isotropically to yield isotropic aerogels, while oriented aerogels were prepared by directional freezing. These aerogels were highly flexible and porous (similar to 85% void fraction), exhibiting greater than 90% recovery at 50% compressive strain even after 100 compression-decompression cycles. Since such aerogels with low bulk modulus and high anisotropy would be an ideal platform for leveraging the piezoelectric properties of CNCs, we used them to prepare piezoelectric nanogenerator devices and determined their energy transduction behavior. Anisotropic aerogels led to an enhanced open-circuit voltage of 840 mV (at similar to 8 N applied force), which is over 2.6 times higher than isotropic aerogels (320 mV). The energy density of anisotropic aerogels was around 52 nW/cm(2), representing outstanding piezoelectric performance for cellulose-based aerogels. Such aerogels with high compressibility, elastic recovery and exceptional piezoelectric performance could have potential applications in sensors, wearable electronics, etc.</p>10aAerogel10aAnisotropic10aCellulose nanocrystals10aenergy harvesting10aPiezoelectricity1 aRam, Farsa1 aBiswas, Bipul1 aTorris, Arun1 aKumaraswamy, Guruswamy1 aShanmuganathan, Kadhiravan  uhttps://library.ncl.res.in/content/elastic-piezoelectric-aerogels-isotropic-and-directionally-ice-templated-cellulose