@article { ISI:000227550500009, title = {Co-precipitation method for the preparation of nanocrystalline ferroelectric SrBi2Nb2O9 ceramics}, journal = {Journal of Electroceramics}, volume = {14}, number = {1}, year = {2005}, month = {JAN}, pages = {83-87}, publisher = {SPRINGER}, type = {Article}, address = {VAN GODEWIJCKSTRAAT 30, 3311 GZ DORDRECHT, NETHERLANDS}, abstract = {

A simple co-precipitation technique had been successfully applied for the preparation of pure ultrafine single phase SrBi2Nb2O9. Ammonium hydroxide and ammonium oxalate were used to precipitate Sr2+, Bi3+ and Nb5+ cations simultaneously. No pyrochlore phase was found while heating powder at 850 C and pure SrBi2Nb2O9 (SBN) phase was formed as revealed by the X-ray diffraction (XRD) studies. Particle size and morphology was studied by transmission electron microscopy (TEM). The room temperature dielectric constant at 1 kHz is 100. The ferroelectric hysteresis loop parameters of these samples were also studied.

}, keywords = {Ceramics, Chemical synthesis, electronic materials, ferroelectricity, Oxides}, issn = {1385-3449}, doi = {10.1007/s10832-005-6588-y}, author = {Gaikwad, S. P. and Dhage, S. R. and Potdar, H. S. and Samuel, V. and Ravi, V.} } @article { ISI:000229811300003, title = {Coprecipitation technique to prepare ZnM2O6 powders}, journal = {Bulletin of Materials Science}, volume = {28}, number = {3}, year = {2005}, month = {JUN}, pages = {205-207}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A simple coprecipitation technique was successfully applied for the preparation of pure ultrafine single phase, ZnNb2O6 (ZN). Ammonium hydroxide was used to precipitate Zn2+ and Nb5+ cations as hydroxides simultaneously. This precursor on heating at 750 degrees, produced ZN powders. For comparison, ZN powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM).

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02711248}, author = {Deshpande, V. V. and Patil, M. M. and Navale, S. C. and Ravi, V.} } @article { ISI:000230275100022, title = {Preparation of nanocrystalline LiNbO3 by citrate gel method}, journal = {Materials Letters}, volume = {59}, number = {19-20}, year = {2005}, month = {AUG}, pages = {2476-2478}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A gel was formed when an aqueous solution of Li(NO3) NbF5 and citric acid in stoichiometric ratio is heated in a water bath at 100 degrees C. This gel on decomposition at 700 degrees C produced the fine crystallites of ternary oxide, LiNbO3 (LN). The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology was studied by transmission electron spectroscopy (TEM). (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, electronic materials, lithium niobate, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.03.028}, author = {Navale, SC and Samuel, V and Ravi, V} } @article { ISI:000231605600002, title = {Preparation of ultrafine LiTaO3 powders by citrate gel method}, journal = {Bulletin of Materials Science}, volume = {28}, number = {5}, year = {2005}, month = {AUG}, pages = {391-393}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A gel was formed when a aqueous solution of Li(NO3), TaF5 and citric acid in stoichiometric ratio was heated in a water bath. This gel on decomposition at 700 degrees C produced fine crystallites of ternary oxide, LiTaO3 (LT). The phase contents and lattice parameters were studied by powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM).

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02711224}, author = {Navale, SC and Samuel, V and Ravi, V} } @article { ISI:000228698900038, title = {PVA stabilized gold nanoparticles by use of unexplored albeit conventional reducing agent}, journal = {Materials Chemistry and Physics}, volume = {92}, number = {1}, year = {2005}, month = {JUL}, pages = {229-233}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Poly(vinyl alcohol) (PVA) stabilized gold nanoparticles have been prepared in aqueous medium using two different reducing viz.; hydrazine hydrate, a stronger reducing agent and sodium formaldehydesulfoxylate (SFS), a slightly weaker reducing agent. SFS is used for first ever time for reduction of gold metal salt. The PVA stabilized gold nanoparticles solutions are wine red to blood red coloured and are stable over a long period of time with no indication of aggregation. The solution shows strong visible light absorptions in the range of 520-540 nm, characteristics of gold nanoparticles. Powder X-ray diffraction patterns of freshly prepared films containing gold nanoparticles indicated particles size to be about 15 nm. Transmission electron microscopy (TEM) of a more than two-week-old sample revealed well-defined non-agglomerated spherical particles of about 50 nm diameter in solutions. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, electronic materials, Nanostructures, Polymer}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2005.01.016}, author = {Khanna, P. K. and Gokhale, R. and Subbarao, V. V. V. S. and Vishwanath, A. K. and Das, B. K. and Satyanarayana, C. V. V.} } @article { ISI:000230375200016, title = {Synthesis of fine PbE (E = S, Se) powder from direct in situ reduction of sulphur or selenium}, journal = {Materials Chemistry and Physics}, volume = {93}, number = {1}, year = {2005}, month = {SEP}, pages = {91-94}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Lead sulphide and lead selenide have been prepared for the first time, by in situ reduction of elemental S or Se by using aqueous DMF or aqueous SFS as reducing agents and their reaction with lead acetate. The grayish-black powder has been characterized by powder XRD measurement, XPS and SEM/EDAX analysis. Powder X-ray diffraction pattern revealed that cubic PbE (E = S, Se) is formed with a little impurities of lead in case of PbSe. Slightly broader peaks in XRD measurement suggest small particles diameter in the powder. The particle size by using Scheffer{\textquoteright}s formula is found to be about 100 nm. Peaks due to free lead particles are observed in XPS and EDS (in case of PbSe) analysis and SEM analysis indicates agglomerated particles. (c) 2005 Elsevier B.V All rights reserved.

}, keywords = {Chemical synthesis, electronic materials, reduction, Semiconductor}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2005.02.025}, author = {Khanna, P. K. and Subbarao, VVVS and Wagh, M. and Jadhav, P. and Patil, K. R.} } @article { ISI:000235860500029, title = {Chemical methods to synthesize FeTiO3 powders}, journal = {Materials Letters}, volume = {60}, number = {11}, year = {2006}, month = {MAY}, pages = {1425-1427}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Three different techniques were used to synthesize FeTiO3 powders. The first method is simple coprecipitation of both Fe and Ti ions under basic conditions using standard ammonia solution from aqueous ferric nitrate and titanium oxy chloride. This precipitate on heating at 400 degrees C produces ilmenite phase. The second method is to digest hydroxide precipitates at 100 degrees C to form FeTiO3 phase. The third technique is to make use of citrate process to form FeTiO3 powders. The phase contents and lattice parameters were Studied by powder X-ray diffraction (XRD). Particle size and morphology were studied by Transmission Electron Microscopy (TEM). (c) 2005 Elsevier B.V. All tights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, X-ray methods}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.11.041}, author = {Mona, J. and Kale, Sangeeta N. and Gaikwad, A. B. and Murugan, A. Vadivel and Ravi, V.} } @article { ISI:000234951400014, title = {Coprecipitation technique to prepare LiTaO3 powders}, journal = {Materials Letters}, volume = {60}, number = {8}, year = {2006}, month = {APR}, pages = {1047-1048}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple coprecipitation technique had been successfully applied for the preparation of pure ultrafine single phase LiTaO3 (LT). An aqueous mixture of ammonium carbonate and ammonium hydroxide was used to precipitate Li+ and Ta5+ cations as carbonate and hydroxide respectively. This precursor oil heating at 750 degrees C produces LT powders. For comparison, LT powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM). (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.10.074}, author = {Navale, SC and Gaikwad, A. B. and Ravi, V} } @article { ISI:000237439300005, title = {Coprecipitation technique to prepare NaNbO3 and NaTaO3}, journal = {Bulletin of Materials Science}, volume = {29}, number = {2}, year = {2006}, month = {APR}, pages = {123-125}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A simple coprecipitation technique has been used successfully for the preparation of pure, ultrafine, single phases of NaNbO3 (NN) and NaTaO3 (NT). An alcoholic solution of ammonium carbonate and ammonium hydroxide was used to precipitate Na+ and Nb5+ (or Ta5+) cations under basic conditions as carbonate and hydroxide, respectively. On heating at 700 degrees C, these precursors produce respective products. For comparison, both NN and NT powders were also prepared by the traditional solid state method. The phase purity and lattice parameters were studied by powder X-ray diffraction (XRD). The particle size and morphology were studied by scanning electron microscopy (SEM).

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, electronic materials, Oxides, X-ray methods}, issn = {0250-4707}, doi = {10.1007/BF02704604}, author = {Samuel, V and Gaikwad, A. B. and Ravi, V} } @article {Rai, title = {Liquid phase oxidation of alkanes using Cu/Co-perchlorophthalocyanine immobilized MCM-41 under mild reaction conditions}, journal = {Applied Catalysis A-General}, volume = {297}, number = {2}, year = {2006}, month = {JAN}, pages = {220-230}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

{Amino-functionalized MCM-41 (NH2-MCM-41) was used to immobilize CU/CO-Cl16PC complex, i.e. Cu/Co-AM(PS) for liquid phase oxidation of alkanes under mild reaction conditions. Higher rates of reaction and better catalytic activity values were obtained for Cu/Co-AM(PS) as compared to Cu/Co-Cl16PC grafted on (i) amino-functionalized SiO2 [

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.apcata.2005.09.012}, author = {Karandikar, Prashant R. and Chandwadkar, Asha J. and Agashe, M. and Ramgir, N. S. and Sivasanker, S.} } @article { ISI:000241849900010, title = {Novel chemical synthetic route and characterization of zinc selenide thin films}, journal = {Journal of Physics and Chemistry of Solid}, volume = {67}, number = {11}, year = {2006}, month = {NOV}, pages = {2310-2315}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Zinc selenide (ZnSe) thin film have been deposited using chemical bath method on non-conducting glass substrate in a tartarate bath containing zinc sulfate, ammonia, hydrazine hydrate, sodium selenosulfate in an aqueous alkaline medium at 333 K. The deposition parameter of the ZnSe thin film is interpreted in the present investigation. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption, electrical measurements, atomic absorption spectroscopy (AAS). The ZnSe thin layers grown with polycrystalline zinc blende system along with some amorphous phase present in ZnSe film. The direct optical band gap {\textquoteleft}E-g{\textquoteright} for the film was found to be 2.81 eV and electrical conductivity in the order of 10(-8)(Omega cm)(-1) with n-type conduction mechanism. (c) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {chalcogenides, electronic materials}, issn = {0022-3697}, doi = {10.1016/j.jpcs.2006.05.001}, author = {Hankare, P. P. and Chate, P. A. and Delekar, S. D. and Asabe, M. R. and Mulla, Imtiaz S.} } @article { ISI:000238624000017, title = {Synthesis of MgNb2O6 by coprecipitation}, journal = {Materials Research Bulletin}, volume = {41}, number = {7}, year = {2006}, month = {JUL}, pages = {1353-1356}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A simple coprecipitation technique was used successfully to synthesize fine powders of MgNb2O6 (MN) phase. An aqueous mixture of ammonium carbonate and ammonium hydroxide was used to precipitate Mg2+ and Nb5+ cations as carbonate and hydroxide respectively under basic conditions. This precipitate on heating at 750 degrees C produced MN powders. For comparison MN powders were prepared by the traditional solid state method. The phase content and the lattice parameters were studied by powder X-ray diffraction (XRD). Particle size and morphology of the particles were studied by scanning electron microscopy (SEM). (C) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2005.12.009}, author = {Navale, S. C. and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000246158300001, title = {Coprecipitation technique to prepare CoTa2O6 and CoNb2O6}, journal = {Materials Letter}, volume = {61}, number = {11-12}, year = {2007}, month = {MAY}, pages = {2127-2129}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

An aqueous solution of sodium hydroxide was used to coprecipitate cobalt and tantalum (or niobium) ions from their precursors as hydroxides under basic conditions. This precipitate yielded CoTa2O6 (CT) or CoNb2O6 (CN) ceramics on calcining at 700 degrees C, i.e. at a temperature much lower than 900 degrees C, reported for the formation of these powders prepared by the traditional solid state method. The X-ray diffraction (XRD) studies were employed to investigate phase contents and lattice parameters. The morphology of the synthesized powders was investigated by transmission electron microscopy (TEM). (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, electronic materials, Oxides, X-ray methods}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.08.024}, author = {Mulla, Imtiaz S. and Natarajan, N. and Gaikwad, A. B. and Samuel, V. and Guptha, U. N. and Ravi, V.} } @article { ISI:000246158300058, title = {Coprecipitation technique to prepare NiNb2O6}, journal = {Materials Letter}, volume = {61}, number = {11-12}, year = {2007}, month = {MAY}, pages = {2354-2355}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A mixture of ammonium carbonate and ammonium hydroxide was used to coprecipitate nickel and niobium ions as nickel carbonate and niobium hydroxide under basic conditions. This precursor yielded NiNb2O6 (NN) ceramics on calcining at 700 degrees C (at a temperature lower than 800 degrees C which is necessary for the formation of NiNb2O6 when prepared by the traditional solid state method). The average particle size and morphology of these powders were investigated by transmission electron microscope (TEM). (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, Oxides, X-ray methods}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.09.010}, author = {Samuel, V. and Gaikwad, A. B. and Jadhav, A. D. and Natarajan, N. and Ravi, V.} } @article { ISI:000252474200009, title = {Low voltage varistor ceramics based on SnO2}, journal = {Bulletin of Materials Science}, volume = {30}, number = {6}, year = {2007}, month = {DEC}, pages = {583-586}, publisher = {SPRINGER}, type = {Article}, address = {233 SPRING STREET, NEW YORK, NY 10013 USA}, abstract = {

The nonlinear current (I)-voltage (V) characteristics of tin dioxide doped with either Nb2O5 and CoO or Sb2O3 and CoO show promising values of nonlinear coefficient (alpha) values (similar to 11) with low breakdown voltages (E-B, similar to 40 V mm(-1)). The pentavalent antimony or niobium acts as donor and increases the electronic conductivity. The crucial parameter for obtaining low breakdown voltage is the grain size, which depends upon sintering duration and temperature of these oxide ceramics.

}, keywords = {Chemical synthesis, electronic materials, Microstructure, tin oxide, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/s12034-007-0092-8}, author = {Dhage, S. R. and Ravi, V. and Yang, O. B.} } @article { ISI:000243164000035, title = {Novel technique to prepare LiNbO3 at low temperature}, journal = {Materials Letter}, volume = {61}, number = {3}, year = {2007}, month = {FEB}, pages = {765-766}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Fresh niobium hydroxide was first precipitated from NbF5 solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 degrees C) produced pure ultrafine single phase LiNbO3 (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM). (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, LiNbO3, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.05.056}, author = {Samuel, V. and Gaikwad, A. B. and Jadhav, A. D. and Mirji, S. A. and Ravi, V.} } @article { ISI:000253106100026, title = {Low temperature synthesis of SrNb2O6 and SrTa2O6 using hydroxide precursor}, journal = {Materials Letters}, volume = {62}, number = {6-7}, year = {2008}, month = {MAR}, pages = {892-894}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

SrNb2O6 (SN) or SrTA(2)O(6) (ST) compounds were prepared at low temperatures for the first time from hydroxide precursors. A simple procedure of mixing commercially purchased strontium hydroxide and niobium (or tantalum) hydroxide thoroughly together and heating at a low temperature (\<400 degrees C) produced SrNb2O6 (SN) or SrTa2O6 (ST) powders. This is the lowest temperature so far reported for the formation of these phases. These materials are potential candidates for ferroelectric and electro-optic applications. The reaction sequence and evolution of the phase formation were investigated by X-ray diffraction (XRD) studies. The average particle size and morphology of these powders were studied by scanning electron microscopy (SEM). (C) 2007 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.07.006}, author = {Muthurajan, H. and Kumar, H. H. and Koteswara Rao, N. and Pradhan, Sivaram and Jha, Ratnesh Kumar and Ravi, V.} } @article { ISI:000254698300033, title = {Novel technique to prepare LiTaO3 at low temperature}, journal = {Ceramics International}, volume = {34}, number = {3}, year = {2008}, month = {APR}, pages = {669-670}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

Firstly, fresh tantalum hydroxide was precipitated from TaF5 solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and tantalum hydroxides together and heating at a low temperature (450 degrees C) produced pure ultrafine single phase LiTaO3 (LT). This is the lowest temperature so far reported for the formation of LT in the literature. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM). (c) 2006 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {chemical synthesis X-ray diffraction, Electron microscopy, electronic materials, LiTaO3}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2006.11.003}, author = {Muthurajan, H. and Kumar, H. H. and Natarajan, N. and Ravi, V.} } @article { ISI:000256114400005, title = {Synthesis of oleic acid capped copper nano-particles via reduction of copper salt by SFS}, journal = {Materials Chemistry and Physics}, volume = {110}, number = {1}, year = {2008}, month = {JUL}, pages = {21-25}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Synthesis of oleic acid capped copper nano-particles has been carried out by use of sodium formaldehyde sulfoxylate (SFS) in aqueous medium. Nano-copper can be effectively coated with polyvinyl alcohol (PVA). Phase-pure nano-Cu can be obtained when water/acetone was used as aqueous medium. It is observed that the surface plasmon resonance (SPR) phenomena can be controlled during synthesis by the use of suitable reagent system, e.g. absorption band in presence of PVA can be blue shifted. As-prepared copper nano-particles were characterized by X-ray diffraction measurements (XRD), Scanning electron microscopy (SEM), energy dispersive analysis of X-rays (EDAX), thermo gravimetric analysis (TGA) and Fourier transform infra-red spectroscopy (FTIR). XRD analysis revealed broad pattern for fcc crystal structure of copper metal. The particle size by use of Scherrer{\textquoteright}s equation was calculated to be about 20 nm. TGA revealed similar to 10\% weight loss due to the presence of surfactant. FTIR spectroscopy confirmed the presence of oleic acid around the particles. (c) 2008 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, electronic materials, metals, Nanostructure}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2008.01.013}, author = {Khanna, P. K. and Kale, Trupti S. and Shaikh, Mushtaq and Rao, N. Koteswar and Satyanarayana, C. V. V.} }