@article { ISI:000259765600037,
	title = {Poly(o-anisidine) coatings on brass: synthesis, characterization and corrosion protection},
	journal = {Current Applied Physics},
	volume = {9},
	number = {1},
	year = {2009},
	month = {JAN},
	pages = {206-218},
	publisher = {ELSEVIER SCIENCE BV},
	address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS},
	abstract = {<p>Poly(o-anisidine) (POA) coatings were synthesized on brass by electrochemical polymerization of o-anisidine in aqueous salicylate solution by using cyclic voltammetry. These coatings were characterized by cyclic voltammetry, UV-visible absorption spectroscopy., Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The corrosion protection aspects of POA coatings on brass in aqueous 3\% NaCl solution were investigated by potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The potentiodynamic polarization measurements show that the POA coating has ability to protect the brass against corrosion. The corrosion potential was about 0.204 V versus SCE more positive for the POA coated brass than that of uncoated brass and reduces the corrosion rate of brass almost by a factor of 800. The corrosion behavior of the POA coatings was also investigated by EIS through immersion tests performed In aqueous 3\% NaCl solution. The evolution of the impedance parameters with the immersion time was studied and the results Show that the POA acts as a protective coating on brass against corrosion in 3\% NaCl solution. The water uptake and delamination area were also determined to further support the corrosion protection performance of the POA coating. (C) 2008 Elsevier B.V. All rights reserved.</p>},
	keywords = {brass, conducting polymers, Corrosion resistant coatings, cyclic voltammetry, Electrochemical impedance spectroscopy, Electrochemical polymerization, poly(o-anisidine)},
	issn = {1567-1739},
	doi = {10.1016/j.cap.2008.01.012},
	author = {Chaudhari, Sudeshna and Gaikwad, A. B. and Patil, P. P.}
}
@article {44545,
	title = {Study the effect of impact angle on slurry erosion wear of four different ductile materials},
	journal = {Materials Today: Proceedings},
	volume = {5},
	year = {2018},
	month = {APR },
	pages = { 7561-7570},
	type = {Journal Article},
	abstract = {<p>The test rig fabricated for the present work has an ability to study the effect of orientation angle of erosion wear. The particles of Indian Standard sand (Quartz) selected as erodent for the present investigation because it is the most widely occurs in natural slurries. Experimental investigations on erosion behavior of ductile materials AISI SS304, AA 6063, Copper and Brass have been carried out using solid-water mixtures of the above erodent. The erosion wear due to solid-liquid mixture of IS Sand and tap water at different impact angles shows typical ductile erosion behavior for the selected materials. The maximum erosion is observed at 22.5{\textdegree} angle for AISI SS 304, 45o for AA 6063, 22.5o for Copper and 30o for Brass. The minimum erosion is observed at 90o orientation angle for all the materials. The eroded specimens were examined under the Scanning Electron Microscope (SEM) at minimum and maximum wear orientation angles. The SEM micrographs of eroded specimens depict the mechanism of material removal.</p>},
	keywords = {AA 6063, AISI SS304, brass, Copper, Quart, SEM, Slurry erosion},
	issn = {22147853},
	doi = {10.1016/j.matpr.2017.11.428},
	author = {Nandre, Bhushan D. and Desale, Girish R.}
}
