@article { ISI:000241686000011, title = {Novel beaded polymers from telechelic methacrylic ether esters}, journal = {Reactive \& Functional Polymers}, volume = {66}, number = {10}, year = {2006}, month = {OCT}, pages = {1087-1096}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A series of telechelic dimethacrylic ether-esters (MEE) were prepared by solventless reaction of alpha,omega-dihydroxy poly(oxytetramethylene) (polytetrahydrofuran, PTHF) with phthalic anhydride and glycidyl methacrylate (GMA). MEE was polymerized with GMA as well as GMA-ethylene dimethacrylate (EGDM) to form porous beads. The terpolymer beads were observed using optical microscopy and SEM and characterized for internal pore volume, equilibrium volume-swelling ratio and dimethyl formamide and aqueous buffer regain. The morphology of the beads was dictated by the mole fraction and molecular weight of MEE in the feed. Porosity was found to increase with increase in molecular weight of MEE. Thus, porosity as high as 49\%, 50\% and 55\% was observed with MEE of molecular weights 1580, 2580 and 3480, respectively. At a specific terpolymerization feed ratio of monomers, the terpolymers formed transform from gel like structure into a macroporous one, with increase in molecular weight of MEE. (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {ether-ester dimethacrylates, macroporous, Pore size distribution, porosity, telechelics}, issn = {1381-5148}, doi = {10.1016/j.reactfunctpolym.2006.01.020}, author = {Pujari, N. S. and Trivedi, J. and Ingavle, Ganesh C. and Ponrathnam, S.} } @article { ISI:000298535800007, title = {Poly(acrylonitrile) based ultrafiltration membranes: optimization of preparation parameters}, journal = {Desalination}, volume = {282}, number = {SI}, year = {2011}, month = {NOV}, pages = {46-53}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Supported ultrafiltration (UF) membranes based on poly(acrylonitrile) were prepared while varying crucial parameters responsible for controlling membrane porosity, viz.; polymer concentration, solvent and additives in the dope solution. Insight into membrane porosity and morphology was obtained by water flux, solute rejection, bubble point, pore size distribution, SEM and AFM analyses. It was found that merely increasing polymer concentration does not necessarily reduce pore size of membranes. Among four solvents used for the dope solution preparation, N-methyl pyrrolidone was found to offer membranes with optimal combination of flux and rejection of various solutes. Some of the PAN(17) (17\% w/w PAN concentration in the dope solution) membranes prepared using organic acid as the additive (citric acid, tartaric acid or maleic acid) offered 1.2-1.7 times higher flux than the membrane prepared using inorganic salt, ZnCl2 as an additive. The porosity of PAN(17) membrane prepared using CA as an additive was larger as compared to membrane prepared using ZnCl2 as an additive. Atomic force microscopy (AFM) analysis of this membrane exhibited higher surface roughness as compared to the ZnCl2 based membrane. Both these membranes exhibited bacteria (E. Coli) log reduction value (LRV) of at least 6; depicting applicability of these membrane for water disinfection. (C) 2011 Elsevier B.V. All rights reserved.

}, keywords = {Additive, Bacteria rejection, Poly(acrylonitrile), Pore size distribution, Ultrafiltration}, issn = {0011-9164}, doi = {10.1016/j.desal.2011.04.009}, author = {Lohokare, Harshada R. and Bhole, Yogesh S. and Taralkar, Suyog and Kharul, Ulhas K.} } @article {44633, title = {Solvent and pH-stable poly(2,5-benzimidazole) (ABPBI) based UF membranes: preparation and characterizations}, journal = {Journal of Membrane Science}, volume = {563}, year = {2018}, month = {OCT }, pages = {743-751}, abstract = {

Poly(2,5-benzimidazole), commonly known as ABPBI, is an excellent thermo-chemically stable polymer that is widely evaluated as a proton exchange membrane material in a fuel cell. Its niche intrinsic characteristics could be highly useful in the membrane preparation for various separation applications, especially under harsher environments. To gain insights towards this feasibility, ABPBI based supported membranes were prepared by phase inversion method. Effects of the nonwoven porous support material (polypropylene/polyester), non-solvent (water/0.5 N NaOH) and polymer concentration (6 or 4 wt\%) on the membrane properties (water flux, rejection and porosity) were investigated. The stability of these membranes towards common organic solvents, concentrated acid (25 N H2SO4), base (2.5 N NaOH) and an autoclave condition was analyzed. ABPBI membrane showed a pore collapse after drying. In order to avoid this, the glycerol treatment was not only found to be suitable but also repeatable, without significant deviations in the water flux.

}, keywords = {ABPBI membrane, Pore size distribution, Solvent stable membranes, Ultrafiltration}, issn = {0376-7388}, doi = {10.1016/j.memsci.2018.06.052}, author = {Lohokare, Harshada R. and Chaudhari, Harshal D. and Kharul, Ulhas. K.} }