@article { ISI:000359867300004,
	title = {Extrusion film casting of long chain branched polypropylene},
	journal = {Polymer Engineering and Science},
	volume = {55},
	number = {9},
	year = {2015},
	month = {SEP},
	pages = {1977-1987},
	publisher = {WILEY-BLACKWELL},
	address = {111 RIVER ST, HOBOKEN 07030-5774, NJ USA},
	abstract = {<p>Extrusion film casting (EFC) is an important melt processing operation which is extensively used to make polypropylene (PP) films. Linear PP shows significant amount of necking and draw resonance during EFC. One of the ways to reduce necking is to introduce long chain branches (LCB) on the polymer backbone. The long branches impart extensional strain hardening behavior thereby stabilizing the melt flow. In this work, we investigate the influence of long chain branching in polypropylene on the extent of necking in the EFC process. Laboratory scale EFC experiments were performed on homopolymer PP of linear and long chain branched architectures. Simulations of the EFC process were carried out using the one-dimensional flow model of Silagy et al., Polym. Eng. Sci.,36, 2614 (1996) into which we incorporate two different multi-mode molecular constitutive equations namely, the eXtended Pom-Pom{\textquoteright} equation (XPP, for long chain branched PP) and the Rolie-Poly{\textquoteright} equation (RP-S, for linear PP). Our experimental data confirm that presence of long chain branching in PP reduces the extent of necking and our numerical predictions show qualitative agreement with experimental data, thereby elucidating the role of chain architecture on the extent of necking. POLYM. ENG. SCI., 55:1977-1987, 2015. (c) 2014 Society of Plastics Engineers</p>},
	issn = {0032-3888},
	doi = {10.1002/pen.24039},
	author = {Chikhalikar, Kalyani and Banik, Sourya and Azad, Lal Busher and Jadhav, Kishor and Mahajan, Sunil and Ahmad, Zubair and Kulkarni, Surendra and Gupta, Surendra and Doshi, Pankaj and Pol, Harshawardhan and Lele, Ashish K.}
}
@article { ISI:000376515100003,
	title = {Effect of plug temperature on the strain and thickness distribution ofcomponents made by plug assist thermoforming},
	journal = {International Polymer Processing},
	volume = {31},
	number = {2},
	year = {2016},
	month = {MAY},
	pages = {166-178},
	publisher = {CARL HANSER VERLAG},
	address = {KOLBERGERSTRASSE 22, POSTFACH 86 04 20, D-81679 MUNICH, GERMANY},
	abstract = {<p>Plug temperature is a key parameter affecting the thickness distribution of thermoplastic components made by plug assist thermoforming. For a specified pair of plug and plastic sheet, the variation in plug temperature can alter the coefficient of friction (COF) between the pair. We show here how the temperature dependence of COF influences the nature and extent of biaxial stretching of the sheet and consequently the thickness distribution of the thermoformed component. In the present study, high impact polystyrene (HIPS) sheets were thermoformed into axisymmetric cups using a plug-assist process in which the aluminum plug temperature (T-plug) was varied from ambient to above the glass transition temperature of HIPS (similar to 100 degrees C). Biaxial strain maps on the surfaces of the formed cups were measured and quantified using Grid Strain Analysis (GSA). Thickness distributions of the cups were also measured. Temperature dependent COF between HIPS and aluminum was determined independently using a rotational rheometer. The measured COF was low for T \&lt; 100 degrees C, whereas it increased appreciably at and above 100 degrees C. We conclude that when T-plug \&lt; 100 degrees C the HIPS sheet slips on the plug during forming, and this results in biaxial stretching of the base and walls of the formed cup. In contrast for T-plug \&gt; 100 degrees C, a significant reduction in the magnitude of slip is expected. Here the sheet is gripped at the clamp and by the plug during forming which causes reduced biaxial stretching of the base and increased uniaxial stretching of the walls of the cup. Simulations of plug-assist thermoforming using a temperature dependent COF showed qualitative agreement with the GSA data thereby supporting our inferences.</p>},
	issn = {0930-777X},
	doi = {10.3139/217.3060},
	author = {Marathe, D. and Rokade, D. and Azad, Lal Busher and Jadhav, Kishor and Mahajan, Sunil and Ahmad, Zubair and Gupta, S. and Kulkarni, S. and Juvekar, Vinay A. and Lele, Ashish K.}
}
