@article { ISI:000229811300003, title = {Coprecipitation technique to prepare ZnM2O6 powders}, journal = {Bulletin of Materials Science}, volume = {28}, number = {3}, year = {2005}, month = {JUN}, pages = {205-207}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A simple coprecipitation technique was successfully applied for the preparation of pure ultrafine single phase, ZnNb2O6 (ZN). Ammonium hydroxide was used to precipitate Zn2+ and Nb5+ cations as hydroxides simultaneously. This precursor on heating at 750 degrees, produced ZN powders. For comparison, ZN powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM).

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02711248}, author = {Deshpande, V. V. and Patil, M. M. and Navale, S. C. and Ravi, V.} } @article { ISI:000237158200003, title = {Phase evolution of NiTiO3 prepared by coprecipitation method}, journal = {Materials Letters}, volume = {60}, number = {15}, year = {2006}, month = {JUL}, pages = {1791-1792}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple coprecipitation technique was used for the preparation of NiTiO3 powders. Ammonium carbonate solution was added to a solution mixture containing stoichiometric amounts of Ni(NO3)(2) and TiOCl2 to precipitate nickel as carbonate and titanium as hydroxide under basic conditions. The precipitate was calcined at different temperatures ranging from 100 to 800 degrees C and phase evolution of NiTiO3 was investigated by X-ray diffraction (XRD) studies. It is observed that nickel titanate was formed at 750 degrees C. For comparison, NiTiO3 was also prepared by standard ceramic process. Particle size and morphology was studied by transmission electron microscopy (TEM). (c) 2005 Elsevier B.V. All fights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, NiTiO3, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.12.023}, author = {Murugan, A. Vadivel and Samuel, V. and Navale, S. C. and Ravi, V.} } @article { ISI:000234951400008, title = {Preparation of nanocrystalline ferroelectric BaBi4Ti4O15 by Pechini method}, journal = {Materials Letters}, volume = {60}, number = {8}, year = {2006}, month = {APR}, pages = {1023-1025}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A gel was formed when an aqueous solution of BaCl2, BiNO3, TiOCl2 and citric acid in stoichiometric ratio is heated on a water bath. This gel on decomposition at 600 degrees C produced the nano crystallites of ternary oxide, BaBi4Ti4O15 (BBT). The phase contents and lattice parameters were Studied by the powder X-ray diffraction (XRD). Particle size and morphology was studied by transmission electron spectroscopy (TEM). The room temperature dielectric constant at I KHz is 90. The ferroelectric hysteresis loop parameters of these samples were also studied by a home built Sawyer-tower circuit. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {dielectric properties, Electron microscopy, ferroelectric properties, powders chemical preparation}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.10.068}, author = {Murugan, A. Vadivel and Navale, S. C. and Ravi, V.} } @article { ISI:000238624000017, title = {Synthesis of MgNb2O6 by coprecipitation}, journal = {Materials Research Bulletin}, volume = {41}, number = {7}, year = {2006}, month = {JUL}, pages = {1353-1356}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A simple coprecipitation technique was used successfully to synthesize fine powders of MgNb2O6 (MN) phase. An aqueous mixture of ammonium carbonate and ammonium hydroxide was used to precipitate Mg2+ and Nb5+ cations as carbonate and hydroxide respectively under basic conditions. This precipitate on heating at 750 degrees C produced MN powders. For comparison MN powders were prepared by the traditional solid state method. The phase content and the lattice parameters were studied by powder X-ray diffraction (XRD). Particle size and morphology of the particles were studied by scanning electron microscopy (SEM). (C) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2005.12.009}, author = {Navale, S. C. and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000244008300030, title = {Co-precipitation technique to prepare BaTa2O6}, journal = {Ceramics International}, volume = {33}, number = {2}, year = {2007}, month = {JAN}, pages = {297-299}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A mixture of ammonium oxalate and ammonium hydroxide was used to co-precipitate barium and tantalum ions as barium oxalate and tantalum hydroxide under basic conditions. On calcination at 750 degrees C, this precursor yielded BaTa2O6 (BT) ceramics. This is much lower temperature as compared to that prepared by traditional solid-state method (1000 degrees C) as reported for the formation of BaTa206. Transmission electron microscope (TEM) investigations revealed that the average particle size is 70 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 100. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {barium tantalate, Ceramics, Electron microscopy, Oxides, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.08.012}, author = {Navale, S. C. and Samuel, Violet and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000244008300028, title = {Influence of surfactant on ZnO varistors}, journal = {Ceramics International}, volume = {33}, number = {2}, year = {2007}, month = {MAR}, pages = {289-291}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

ZnO varistors with and without surfactant such as sodium dodecyl sulphate (SIDS) are prepared by nitrate-combustion process. The samples were identically heat treated and sintered at 1000 degrees C for 12 h to study the influence of the surfactant on the nonlinear electrical properties of polycrystalline ZnO. It is observed that the nonlinear coefficient decreases marginally (alpha = 35) for samples prepared with surfactant, whereas breakdown field (E-B = 130 V/mm) decreased significantly. The corresponding parameters for the samples synthesized without surfactant are alpha = 45 and E-B = 400 V/mm. Hence, this method can be used for the manufacture of varistors with low to moderate breakdown fields. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {Chemical synthesis, Semiconductors, X-ray methods, ZnO}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.08.010}, author = {Dhage, S. R. and Navale, S. C. and Ravi, V.} } @article { ISI:000250178900006, title = {Low temperature synthesis and NOx sensing properties of nanostructured Al-doped ZnO}, journal = {Sensors and Actuators B-Chemical}, volume = {126}, number = {2}, year = {2007}, month = {OCT}, pages = {382-386}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Although ZnO is studied intensively as a sensing material, there are limited reports available on aluminum-doped ZnO (AZO) as a NO, sensor. This paper reports selective NO, sensing characteristics of M-doped ZnO synthesized in the form of porous pellets sintered at 350 degrees C. The salient feature of our experimental results is that our sensor can detect small concentrations of NO, at lower operating temperature. It is also observed that as compared to gases such as SOx HCl, LPG, H2S, H-2, ammonia, alcohol and acetone it selectively detects NOx due to Al-doping. The amount of Al in ZnO during synthesis is varied between 1 and 10 wt\%. Our sensor senses NO, concentration as low as 20ppm at 100 degrees C with a \%response of 11 and a \%response of 740 at 300 degrees C for 1 wt\% Al. Of all the compositions with Al-doping, I wt\% is found to give best results. Sensing experiments carried out at 350 C, however. do not show any significant improvement in the gas sensing properties. The phase contents and lattice parameters were determined by XRD and the average particle size was obtained using Scherrer formula. A probable mechanism for sensing NO, involving oxygen ion adsorption and desorption on the surface of sensor has been suggested. (C) 2007 Elsevier B.V. All rights reserved.

}, keywords = {aluminum doping, nanomaterial, NOx, Sensor, ZnO}, issn = {0925-4005}, doi = {10.1016/j.snb.2007.03.019}, author = {Navale, S. C. and Ravi, V. and Mulla, Imtiaz S. and Gosavi, S. W. and Kulkarni, S. K.} } @article { ISI:000244008300031, title = {Varistors based on Ta-doped TiO2}, journal = {Ceramics International}, volume = {33}, number = {2}, year = {2007}, month = {MAR}, pages = {301-303}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

The nonlinear current (I)-voltage (V) characteristics of titanium dioxide are examined when doped with small quantities (0.05-0.5 at.\%) of tantalum pentaoxide. For optimum compositions, the nonlinear coefficients are found to be in the range of 25-30 and the breakdown field strength (EB) is similar to 4000 V/cm. The obtained alpha- and E-B-values are higher than the previously reported values for TiO2 ceramics. The acceptor like surface states at the grain boundary adsorb oxygen during sintering and cooling, leading to formation of grain boundary barrier. The grain boundary barrier height (OB) is calculated using Schottky equation. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {Ceramics, Oxides, Schottky barrier, TiO2, varistor}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.07.026}, author = {Navale, S. C. and Murugan, A. Vadivel and Ravi, V.} }