@article {48493,
	title = {Microporous 3D-structured hierarchically entangled graphene-supported Pt3Co alloy catalyst for PEMFC application with process-friendly features},
	journal = {ACS Applied Materials \& Interfaces},
	volume = {15},
	year = {2023},
	month = {JUN },
	pages = {28023-28035},
	type = {Article},
	abstract = {<p>
	To improve the oxygen reduction reaction(ORR) performance in aproton-exchange membrane fuel cell (PEMFC) cathode with respect tomass activity and durability, a suitable electrocatalyst design strategyis essentially needed. Here, we have prepared a sub-three nm-sizedplatinum (Pt)-cobalt (Co) alloy (Pt3Co)-supportedN-doped microporous 3D graphene (Pt3Co/pNEGF) by usingthe polyol synthesis method. A microwave-assisted synthesis methodwas employed to prepare the catalyst based on the 3D porous carbonsupport with a large pore volume and dense micro-/mesoporous surfaces.The ORR performance of Pt3Co/pNEGF closely matches withthe state-of-the-art commercial Pt/C catalyst in0.1 M HClO4, with a small overpotential of 10 mV. The 3Dmicroporous structure of the N-doped graphene significantly improvesthe mass transport of the reactant and thus the overall ORR performance.As a result of the lower loading of Pt in Pt3Co/pNEGF ascompared to that in Pt/C, the alloy catalyst achieved 1.5 times highermass activity than Pt/C. After 10,000 cycles, the difference in theelectrochemically active surface area (ECSA) and half-wave potential(E (1/2)) of Pt3Co/pNEGF is foundto be 5 m(2) g(Pt) (-1) (Delta ECSA)and 24 mV (Delta E (1/2)), whereas, forPt/C, these values are 9 m(2) g(Pt) (-1) and 32 mV, respectively. Finally, in a realistic perspective, single-celltesting of a membrane electrode assembly (MEA) was made by sandwichingthe Pt3Co/pNEGF-coated gas diffusion layers as the cathodedisplayed a maximum power density of 800 mW cm(-2) under H-2-O-2 feed conditions with aclear indication of helping the system in the mass-transfer region(i.e., the high current dragging condition). The nature of the I-V polarization shows a progressivelylower slope in this region of the polarization plot compared to asimilar system made from its Pt/C counterpart and a significantlyimproved performance throughout the polarization region in the caseof the system made from the Pt3Co/NEGF catalyst (withoutthe microwave treatment) counterpart. These results validate the betterprocess friendliness of Pt3Co/pNEGF as a PEMFC electrode-specificcatalyst owing to its unique texture with 3D architecture and well-definedporosity with better structural endurance.</p>
},
	keywords = {microwave synthesis, N-doped porous 3D graphene, ORR, PEMFC, polyol synthesis, Pt3Co alloy},
	issn = {1944-8244},
	doi = {10.1021/acsami.3c03372},
	author = {Manna, Narugopal and Singh, Mayank and Kurungot, Sreekumar}
}
@article {49596,
	title = {Hot injection assisted electronically modulated twin and grain boundary rich sub-2 nm pt3co alloy resistant to phosphate ion for PEMFCs},
	journal = {Small},
	volume = {21},
	year = {2025},
	month = {MAY},
	type = {Article},
	abstract = {<p>
	Modulation of the electronic d-band center, structural defects (line defects), and particle size of Pt3Co alloy electrocatalyst have huge significance in elevating its electrochemical oxygen reduction reaction activity. Deviating from traditional high-temperature strategies, the current work focuses on ripening these benefits by implying a simple economically viable hot-injection-assisted modified polyol process. A conclusive control over decrementing particle size starting from 2.7 to 1.3 nm, an increasing degree of strain (twin boundary), and shifting of the d-band center away from the Fermi level are obtained via varying the temperature to which the solution is injected. The catalyst prepared via the injection at 200 degrees C (Pt3Co(1.3 t,g-b)/fVC-200) has delivered an electrochemical surface area of 84 m(2) g(Pt)(-1) with the onset and half-wave potentials of 0.980 and 0.858 V, respectively, versus RHE and a limiting current of -6.0 mA cm(-2) with stability till 20k cycles. In the high-temperature proton exchange membrane fuel cell Pt3Co(1.3 t,g-b)/fVC-200-based cell has outperformed Pt/C rendering 600 mWcm(-2) under H-2-Air compared to 529 mWcm(-2) of Pt/C with 20\% lower Pt loading and double the stability due to enhanced resistance toward phosphoric acid for accelerated voltage cycling. A similar enhancement is seen while employing the catalyst for low-temperature fuel cells.</p>
},
	keywords = {electrocatalyst, grain boundary, hot injection synthesis, modified polyol process, oxygen reduction reaction, proton exchange membrane fuel cell, Pt3Co alloy, twin boundary, valance band X-ray photoelectron spectroscopy},
	issn = {1613-6810},
	doi = {10.1002/smll.202500954},
	author = {Singh, Mayank U. and Jadhav, Swapnil D. and Shivankar, Bhavana R. and Pandikassala, Ajmal and Kumar, Yogesh and Krishnamurty, Sailaja and Vinod, C. P. and Kurungot, Sreekumar}
}
