@article { ISI:000321965700043, title = {Direct contact heat transfer via injecting volatile liquid in a hot liquid pool: generation and motion of bubbles}, journal = {Chemical Engineering Science}, volume = {100}, year = {2013}, note = {11th International Conference on Gas-Liquid and Gas-Liquid-Solid Reactor Engineering (GLS) Held in Conjunction with 9th World Congress on Chemical Engineering (WCCE) / Asian Pacific Conference on Chemical Engineering (APCChE), Seoul, SOUTH KOREA, AUG 19-22, 2013}, month = {AUG}, pages = {421-432}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Direct contact heat transfer via injection of volatile liquid is an effective strategy for removing heat from a viscous liquid pool. The rapid evaporation effectively removes heat and the generated bubbles move quickly to the top surface. In this paper, we present an experimental and phenomenological analysis of the evaporation of a drop in a slightly miscible liquid. The phenomenon was visualized using a two-dimensional transparent experimental set-up with a single inlet at the bottom. The videos were used to estimate bubble dimensions, its rise velocity, distance from the detachment point, and fraction of vapor and the liquid phases in the evaporating drop. The initial drop size, temperature difference between the hot fluid and the low boiling solvent and the nucleation rate governed the rate of change of the drobble (combined entity of drop and bubble) diameter and its rise velocity. A phenomenological model describing transient behavior of drobble (motion and heat transfer) is developed. The transient variation in the interfacial areas for heat transfer and the projected area were found to have effect on the predictions. The model and results will also provide useful basis for extending the work towards better understanding of direct contact heat transfer in viscous systems like polymerization reactors. (C) 2013 Elsevier Ltd. All rights reserved.

}, keywords = {Bubble, Direct contact HT, Drobble, Drop, Evaporation, Slightly miscible liquids}, issn = {0009-2509}, doi = {10.1016/j.ces.2013.02.057}, author = {Kulkarni, Amol A. and Ranade, Vivek V.} } @article { ISI:000365930800010, title = {Development of newer adsorbents: activated carbons derived from carbonized cassia fistula}, journal = {Industrial \& Engineering Chemistry Research}, volume = {54}, number = {47}, year = {2015}, month = {DEC}, pages = {11844-11857}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

Development of newer adsorbent materials, especially from biomass, is most crucial to sustain growth of otherwise well established adsorption processes that already have hundreds of commercial adsorbents in practice. In the present study, newer adsorbents and their potential-carbonaceous adsorbents derived from the whole fruit of Cassia fistula (Golden shower) have been reported for applications in environmental pollution control using natural, renewable biomass as precursor. The potential of different forms of the derived adsorbents produced by thermal and chemical activation was examined for two representative cases, desulfurization of transportation fuels and wastewater treatment. The adsorbents were characterized by FTIR, XRD, XPS, and SEM techniques that indicate specific characteristics useful as an adsorbent. A successful application in the real industrial wastewater treatment and comparison with well recognized commercial adsorbents clearly highlights the utility of the developed newer adsorbents in separation science and technology.

}, issn = {0888-5885}, doi = {10.1021/acs.iecr.5b02945}, author = {Sorokhaibam, Laxmi Gayatri and Bhandari, Vinay M. and Salvi, Monal S. and Jain, Saijal and Hadawale, Snehal D. and Ranade, Vivek V.} } @article { ISI:000371228200017, title = {Differentiating process performance of various coagulants in removal of congo red and orange G dyes}, journal = {International Journal of Chemical Reactor Engineering}, volume = {14}, number = {1}, year = {2016}, month = {FEB}, pages = {195-211}, publisher = {WALTER DE GRUYTER GMBH}, address = {GENTHINER STRASSE 13, D-10785 BERLIN, GERMANY}, abstract = {

Two refractory azo dyes-Congo red and Orange G, especially at high concentrations were subjected to coagulation with different conventional coagulants and newer formulations developed from Aluminum sulfate, Iron (III) chloride, Aluminium chloride, Poly diallydimethylammonium chloride (Poly DADMAC) and Poly Aluminium Chloride (PAC). The highest COD reduction of 99 \% was obtained with PAC SAB 18 (Powder Grade PAC) for Congo red at pH 4.5 while the color removal of 99 \% was achieved with almost all the coagulants in the present study at specific pH within 3-8. The optimum dose for the iron-based coagulant is 200 mg/L while that of aluminum-based coagulants and PAC is 150-200 mg/L. Results showed that Orange G was more difficult to remove with a maximum COD removal of 65 \% and 35 \% color removal using various formulations. The combinational formulations of inorganic-inorganic and inorganic- organic produced a substantial enhancement in COD and color removal and reduced sludge. PAC-Fe30/70 produces the minimum sludge of 50 mL/g on Congo red. pH in the range 3-9 showed high reductions in COD and color (90-99 \%) for Congo red while jerky rise in COD and color reduction was observed in the case of Orange G after pH 9. An attempt to understand the dye coagulation mechanism has been made based on the specific difference in dye structure and cation speciation.

}, keywords = {coagulation, Congo red, dye removal, Orange G, Wastewater treatment}, issn = {2194-5748}, doi = {10.1515/ijcre-2015-0083}, author = {Prajapati, Kavita and Sorokhaibam, Laxmi Gayatri and Bhandari, Vinay M. and Killedar, D. J. and Ranade, Vivek V.} } @article {43829, title = {Deployment of underground coal gasification in India}, journal = {Current Science}, volume = {113}, year = {2017}, month = {JUL}, pages = {218-227}, type = {Article}, doi = {10.18520/cs/v113/i02/218-227}, author = {Singan, Akshay and Ranade, Vivek V.} } @article {46620, title = {Destroying antimicrobial resistant bacteria (AMR) and difficult, opportunistic pathogen using cavitation and natural oils/plant extract}, journal = {Ultrasonics Sonochemistry}, volume = {69}, year = {2020}, month = {DEC}, pages = {105272}, type = {Article}, abstract = {

The present study reports, for the first time, a new and techno-economic strategy for effective removal of antimicrobial resistant bacteria (AMR) and difficult, opportunistic pathogen using cavitation and natural oils/plant extract. A hybrid methodology using natural oils of known health benefits has been discussed in combination with conventional physico-chemical method of hydrodynamic cavitation that not only provides efficient and effective water disinfection, but also eliminates harmful effects of conventional methods such as formation of disinfection by-products apart from reducing cost of treatment. A proof-of concept is demonstrated by achieving exceptionally high rates for practically complete removal of antimicrobial resistant (AMR) and relatively less researched, gram-negative opportunistic pathogen, Pseudomonas aeruginosa and gram-positive methicillin resistant, Staphylococcus aureus using a natural oil-Peppermint oil and two different cavitating reactors employing vortex flow (vortex diode) and linear flow (orifice) for hydrodynamic cavitation. \> 99\% disinfection could be obtained, typically in less than 10 min, using vortex diode with operating pressure drop of 1 bar and low dose of 0.1\% peppermint oil as an additive, depicting very high rates of disinfection. The rate of disinfection can be further increased by using simple aeration which can result in significant lowering of oil dose. The conventional device, orifice requires relatively higher pressure drop of 2 bar and comparatively more time (similar to 20 min) for disinfection. The cost of the disinfection was also found to be significantly lower compared to most conventional processes indicating techno-economic feasibility in employing the developed hybrid method of disinfection for effectively eliminating bacteria including AMR bacteria from water. The developed approach not only highlights importance of going back to nature for not just conventional water disinfection, but also for eliminating hazardous AMR bacteria and may also find utility in many other applications for the removal of antimicrobial bacteria.

}, keywords = {AMR bacteria, Cavitation, Disinfection, Oil, Water treatment}, issn = {1350-4177}, doi = {10.1016/j.ultsonch.2020.105272}, author = {Mane, Maya B. and Bhandari, Vinay M. and Balapure, Kshama and Ranade, Vivek V.} }