01847nas a2200241 4500008004100000022001400041245013000055210006900185260000800254300001400262490000700276520096700283653001601250653002201266653001801288653004701306653003601353100002401389700002701413700001701440700002601457856012201483 2020 eng d a1672-652900aEffect of bio-filler on hybrid sisal-banana-kenaf-flax based epoxy composites: a statistical correlation on flexural strength0 aEffect of biofiller on hybrid sisalbananakenafflax based epoxy c cNOV a1263-12710 v173 a

This work deals with the investigation of the synergistic effect of bagasse ash with sisal-banana-kenaf-flax fibers reinforced epoxy composite for their flexural behavior. The composites with three combinations of hybrid fibers viz. sisal/kenaf (HSK), banana/kenaf (HBK), and banana/flax (HBF) with bagasse ash (BGA) as filler material are fabricated using vacuum bag assisted resin transfer molding. Experiments were conducted based on L27 orthogonal array to understand the influence of control factor viz. fiber volume, alkali concentration & BGA over output response.X-ray micro computed tomography analysis was conducted over the developed sample to infer the uniform dispersion of fiber and filler material. The experimental results reveal that the addition of fiber up to 30 vol% depicts better strength and further addition results in a negative impact. Increasing in order of BGA decreases the flexural strength of the developed composites.

10abagasse ash10aflexural strength10anatural fiber10avacuum bag assisted resin transfer molding10aX-ray micro computed tomography1 aVivek, Somasundaram1 aKanthavel, Karuppusamy1 aTorris, Arun1 aKavimani, Vijayananth uhttp://library.ncl.res.in/content/effect-bio-filler-hybrid-sisal-banana-kenaf-flax-based-epoxy-composites-statistical02018nas a2200241 4500008004100000022001400041245009000055210006900145260000800214300001400222490000700236520121900243653001601462653001801478653001501496653003701511653001801548653002601566100001901592700001701611700003101628856011701659 2020 eng d a0032-388800aEnhancing the mechanical properties of 3D printed polylactic acid using nanocellulose0 aEnhancing the mechanical properties of 3D printed polylactic aci cAUG a1842-18550 v603 a

We report here a systematic investigation of the mechanical properties of polylactic acid (PLA) processed by fused filament fabrication (FFF) 3D printing vs PLA processed by compression molding. Our results show that the tensile strength and modulus of FFF-PLA is 49% and 41% lower, respectively, than compression molded samples of PLA. We also demonstrate here an approach to augment the mechanical properties of 3D printed PLA using nanocellulose. Incorporation of a small quantity (1 wt%) of cellulose nanofibers (CNF) was found to enhance the tensile strength and modulus of 3D printed PLA by 84% and 63%, respectively. X-ray microtomography was used to probe the morphology of 3D printed PLA and PLA/CNF composites. 3D printed PLA/CNF composites had significantly lesser voids as compared to neat 3D printed PLA. Differential scanning calorimetry study revealed that CNF can accelerate the nucleation and crystallization of 3D printed PLA leading to enhanced crystallinity. The thermal stability of 3D printed PLA/CNF composites was not compromised by the addition of CNF. The enhanced mechanical properties of 3D printed PLA/CNF composites can be ascribed to higher crystallinity and lesser defects.

10a3D printing10aBiocomposites10acomposites10afused filament fabrication (FFF)10aNanocellulose10apolylactic acid (PLA)1 aAmbone, Tushar1 aTorris, Arun1 aShanmuganathan, Kadhiravan uhttp://library.ncl.res.in/content/enhancing-mechanical-properties-3d-printed-polylactic-acid-using-nanocellulose02151nas a2200253 4500008004100000022001400041245015200055210006900207260000800276300001400284490000700298520126500305653001201570653001601582653002701598653002201625653002101647100001501668700001801683700001701701700002701718700003101745856012101776 2021 eng d a0969-023900aElastic piezoelectric aerogels from isotropic and directionally ice-templated cellulose nanocrystals: comparison of structure and energy harvesting0 aElastic piezoelectric aerogels from isotropic and directionally  cJUL a6323-63370 v283 a

We report the preparation of highly compressible and elastic piezoelectric aerogels of carboxylated cellulose nanocrystals (CNCs). Aqueous CNC dispersions containing polyethyleneimine and crosslinker were frozen isotropically to yield isotropic aerogels, while oriented aerogels were prepared by directional freezing. These aerogels were highly flexible and porous (similar to 85% void fraction), exhibiting greater than 90% recovery at 50% compressive strain even after 100 compression-decompression cycles. Since such aerogels with low bulk modulus and high anisotropy would be an ideal platform for leveraging the piezoelectric properties of CNCs, we used them to prepare piezoelectric nanogenerator devices and determined their energy transduction behavior. Anisotropic aerogels led to an enhanced open-circuit voltage of 840 mV (at similar to 8 N applied force), which is over 2.6 times higher than isotropic aerogels (320 mV). The energy density of anisotropic aerogels was around 52 nW/cm(2), representing outstanding piezoelectric performance for cellulose-based aerogels. Such aerogels with high compressibility, elastic recovery and exceptional piezoelectric performance could have potential applications in sensors, wearable electronics, etc.

10aAerogel10aAnisotropic10aCellulose nanocrystals10aenergy harvesting10aPiezoelectricity1 aRam, Farsa1 aBiswas, Bipul1 aTorris, Arun1 aKumaraswamy, Guruswamy1 aShanmuganathan, Kadhiravan uhttp://library.ncl.res.in/content/elastic-piezoelectric-aerogels-isotropic-and-directionally-ice-templated-cellulose