@article { ISI:000227550500009, title = {Co-precipitation method for the preparation of nanocrystalline ferroelectric SrBi2Nb2O9 ceramics}, journal = {Journal of Electroceramics}, volume = {14}, number = {1}, year = {2005}, month = {JAN}, pages = {83-87}, publisher = {SPRINGER}, type = {Article}, address = {VAN GODEWIJCKSTRAAT 30, 3311 GZ DORDRECHT, NETHERLANDS}, abstract = {

A simple co-precipitation technique had been successfully applied for the preparation of pure ultrafine single phase SrBi2Nb2O9. Ammonium hydroxide and ammonium oxalate were used to precipitate Sr2+, Bi3+ and Nb5+ cations simultaneously. No pyrochlore phase was found while heating powder at 850 C and pure SrBi2Nb2O9 (SBN) phase was formed as revealed by the X-ray diffraction (XRD) studies. Particle size and morphology was studied by transmission electron microscopy (TEM). The room temperature dielectric constant at 1 kHz is 100. The ferroelectric hysteresis loop parameters of these samples were also studied.

}, keywords = {Ceramics, Chemical synthesis, electronic materials, ferroelectricity, Oxides}, issn = {1385-3449}, doi = {10.1007/s10832-005-6588-y}, author = {Gaikwad, S. P. and Dhage, S. R. and Potdar, H. S. and Samuel, V. and Ravi, V.} } @article { ISI:000227447800012, title = {Coprecipitation technique to prepare BaNb2O6}, journal = {Materials Science and Engineering B-Solid State Materials for Advanced Technology}, volume = {117}, number = {2}, year = {2005}, month = {MAR}, pages = {169-171}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

A mixture of ammonium oxalate and ammonium hydroxide was used to coprecipitate barium and niobium ions as barium oxalate and niobium hydroxide under basic conditions. This precursor on calcination at 750degreesC yielded BaNb2O6 ceramics. This is a much lower temperature as compared to that prepared by traditional solid-state method (1000degreesC), as reported for the formation of BaNb2O6. Transmission electron microscope (TEM) investigations revealed that the average particle size is 100 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 1100. The ferroelectric hysteresis loop parameters of these samples were also studied. (C) 2004 Elsevier B.V. All rights reserved.

}, keywords = {Ammonia, Ceramics, Electron microscopy, niobium oxide, Oxides}, issn = {0921-5107}, doi = {10.1016/j.mseb.2004.11.009}, author = {Natarajan, N and Samuel, V and Pasricha, R and Ravi, V} } @article { ISI:000230160700011, title = {Coprecipitation technique to prepare SrNb2O6}, journal = {Materials Characterization}, volume = {55}, number = {1}, year = {2005}, month = {JUL}, pages = {92-95}, publisher = {ELSEVIER SCIENCE INC}, type = {Article}, address = {360 PARK AVE SOUTH, NEW YORK, NY 10010-1710 USA}, abstract = {

A mixture of ammonium oxalate and ammonium hydroxide was used to co-precipitate strontium and niobium ions as strontium oxalate and niobium hydroxide under basic conditions. This precursor yielded SrNb2O6 ceramics on calcining at 650 degrees C. This is a much lower temperature compared to preparation of SrNb2O6 by the traditional solid state method (900 degrees C). Transmission electron microscopy (TEM) revealed that the average particle size is 100 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 550. The ferroelectric hysteresis loop parameters of these samples were also studied. (c) 2005 Elsevier Inc. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, ferroelectric, Oxides, X-ray methods}, issn = {1044-5803}, doi = {10.1016/j.matchar.2005.04.002}, author = {Ravi, V} } @article { ISI:000232864800029, title = {Low temperature synthesis of MgTa2O6 powders}, journal = {Materials Letters}, volume = {59}, number = {29-30}, year = {2005}, month = {DEC}, pages = {3926-3928}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A combination of digestion and further low temperature calcination to crystallize the product is employed to prepare MgTa2O6 (MT) ceramics. Freshly prepared niobium hydroxide gel is mixed with magnesium hydroxide thoroughly and allowed to react at 100 degrees C under refluxing and stirring conditions for 6-12 h. The X-ray amorphous product so formed is heated at 550 degrees C to form crystalline MgTa2O6. This is the lowest temperature so far reported for the formation of MgTa2O6. For comparison, MT powders were also prepared by the traditional solid state method. Transmission electron microscope (TEM) investigations revealed that the average particle size is 40 nm for the low temperature calcined powders. (C) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, magnesium tantalate, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.07.035}, author = {Navale, SC and Samuel, V and Ravi, V} } @article { ISI:000228797100048, title = {Preparation of ferroelectric BaNb2O6 the urea method}, journal = {Materials Letters}, volume = {59}, number = {14-15}, year = {2005}, month = {JUN}, pages = {1929-1931}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A precipitate was formed when an aqueous solution of BaCl2, NbF5 and urea in required ratio (the ratio of total metal cations to the urea is five) is heated on a water bath at 100 degrees C. This precipitate on decomposition at 600 degrees C yielded the nanocrystallites of BaNb2O6 (BN), as confirmed by X-ray diffraction study (XRD). This is a much lower temperature as compared to that prepared by traditional solid state method (1000 degrees C) as reported for the formation of BaNb2O6. Transmission electron microscope (TEM) investigations revealed that the average particle size is 85 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 900. The ferroelectric hysteresis loop parameters of these samples were also studied. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, electronic material, ferroelectricity, Oxides}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.02.028}, author = {Dhage, S. R. and Pasricha, R. and Ravi, V.} } @article { ISI:000228253200008, title = {Preparation of nanocrystalline ferroelectric BaNb(2)O6 by citrate gel method}, journal = {Bulletin of Materials Science}, volume = {28}, number = {2}, year = {2005}, month = {APR}, pages = {121-123}, publisher = {INDIAN ACADEMY SCIENCES}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A gel was formed when a aqueous solution of BaCl2, NbF5 and citric acid in stoichiometric ratio is heated on a water bath. This gel on decomposition at 600 degrees C yielded the nano crystallites of BaNb2O6, as confirmed by X-ray diffraction study (XRD). This is a much lower temperature as compared to that prepared by traditional solid state method (1000 degrees C) as reported for the formation of BaNb2O6. Transmission electron microscopic. (TEM) investigations revealed that the average particle size is 50 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 1000. The ferroelectric hysteresis loop parameters of these samples were also studied.

}, keywords = {Ceramics, Chemical synthesis, electronic material, ferroelectricity, Oxides}, issn = {0250-4707}, doi = {10.1007/BF02704230}, author = {Gaikwad, S. P. and Samuel, V and Pasricha, R and Ravi, V} } @article { ISI:000230275100032, title = {Synthesis of bismuth oxide nanoparticles at 100 degrees C}, journal = {Materials Letters}, volume = {59}, number = {19-20}, year = {2005}, month = {AUG}, pages = {2523-2525}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple gel to crystal conversion route has been followed for the preparation of ultrafine Bi2O3 particles at 80-100 degrees C under refluxing conditions. Freshly prepared bismuth hydroxide gel is allowed to crystallize under refluxing and stirring conditions for 6-12 h. Formation of nanocrystallites of Bi2O3 is confirmed by X-ray diffraction (XRD) study. The thermal decomposition of bismuth hydroxide yields Bi2O3 only at 400 degrees C. This shows the advantage of the present method. Transmission electron microscope (TEM) investigations revealed that the average particle size is 50 nm for these oven-dried powders. (c) 2005 Elsevier B.V All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.03.037}, author = {Patil, M. M. and Deshpande, V. V. and Dhage, S. R. and Ravi, V.} } @article { ISI:000226803200008, title = {Synthesis of fine particles of ZnO at 100 degrees C}, journal = {Materials Letters}, volume = {59}, number = {7}, year = {2005}, month = {MAR}, pages = {779-781}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple gel to crystal conversion route has been followed for the preparation of fine ZnO at 80-100 degreesC under refluxing conditions. Freshly prepared zinc hydroxide gel is allowed to crystallize under refluxing and stirring conditions for 4-6 It. Formation of fine crystallites of ZnO is confirmed by X-ray diffraction (XRD) study. Transmission electron microscope (TEM) investigations revealed that the average particle size is 100 nm for these powders. (C) 2004 Elsevier B.V All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2004.11.019}, author = {Dhage, S. R. and Pasricha, R. and Ravi, V.} } @article { ISI:000228510500005, title = {Synthesis of nanocrystalline Mn3O4 at 100 degrees C}, journal = {Materials Research Bulletin}, volume = {40}, number = {4}, year = {2005}, month = {APR}, pages = {605-609}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A simple gel to crystal conversion route has been followed for the preparation of nanocrystalline tetragonal Mn3O4 powders at 80-100 degrees C under refluxing conditions. Freshly prepared manganese hydroxide gel is allowed to crystallize under refluxing and stirring conditions for 4-6 h. Formation of nano crystallites of Mn3O4 is confirmed by X-ray diffraction (XRD) study. Transmission electron microscope (TEM) investigations revealed that the average particle size is 50 nm for these powders. (c) 2005 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2005.01.009}, author = {Anilkumar, Mettu and Ravi, V.} } @article { ISI:000230338900015, title = {Synthesis of rutile from ATO and stearic acid}, journal = {Materials Letters}, volume = {59}, number = {21}, year = {2005}, month = {SEP}, pages = {2673-2675}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Nanocrystalline titanium dioxide in the rutile phase has been obtained from the solid state reaction between ammonium titanyl oxalate (ATO) and stearic acid at 400 degrees C in air. The fine powders of ATO and stearic acid are mixed well using acetone in an agate mortar and pestle for 2 h. This mixture (weight ratio of ATO to stearic acid \> 5) on heating at 400 degrees C produces rutile powders. For the ratios of ATO to stearic acid \< 5, a mixture of anatase and rutile phases is obtained. Pure ATO yields anatase phase on decomposition at 400 degrees C. These powders were characterized by X-ray diffraction (XRD), BET surface area measurements and transmission electron microscopy (TEM) studies. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray techniques}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.04.016}, author = {Patil, M. M. and Deshpande, V. V. and Deshpande, S. B. and Samuel, V. and Ravi, V.} } @article { ISI:000231592300006, title = {Synthesis of Sr0.5Ba0.5Nb2O6 by citrate gel method}, journal = {Materials Chemistry and Physics}, volume = {94}, number = {1}, year = {2005}, month = {NOV}, pages = {34-36}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

A gel was formed when an aqueous solution of BaCl2, SrCl2, NbF5 and citric acid in stoichiometric ratio is heated on a water bath. This gel on decomposition at 700 degrees C yielded the nanocrystallites of ternary oxide, Sr0.5Ba0.5Nb2O6 (SBN) as confirmed by X-ray diffraction study (XRD). Particle size and morphology was studied by transmission electron spectroscopy (TEM). The room temperature dielectric constant at I kHz is 1000. The ferroelectric hysteresis loop parameters of these samples were also studied by a home built Sawyer-Tower circuit. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, ferroelectricity, Oxides}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2005.04.003}, author = {Pasricha, R and Ravi, V} } @article { ISI:000227164000044, title = {Synthesis of Sr0.5Ba0.5Nb2O6 by urea method}, journal = {Materials Letters}, volume = {59}, number = {8-9}, year = {2005}, month = {APR}, pages = {1053-1055}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A precipitate was formed when an aqueous solution of SrCl2, BaCl2, NbF5 and urea in stoichiometric ratio (total metal cations to urea ratio is 5) is heated on a water bath.. This precipitate on decomposition at 750 degreesC yielded the nanocrystallites of ternary oxide, Sr0.5Ba0.5Nb2O6 (SBN) as confirmed by X-ray diffraction study (XRD). This is much lower temperature as compared to that prepared by traditional solid state method (1000 degreesC as reported for the formation of SBN ceramics. Transmission electron microscope (TEM) investigations revealed that the average particle size is 100 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 1050. The ferroelectric hysteresis loop parameters of these samples were also studied. (C) 2004 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, ferroelectricity, Oxides}, issn = {0167-577X}, doi = {10.1016/j.matlet.2004.12.003}, author = {Dhage, S. R. and Pasricha, R. and Ravi, V.} } @article { ISI:000232196200008, title = {TiO2 ceramic varistor modified with tantalum and barium}, journal = {Materials Science and Engineering B-Solid State Materials for Advanced Technology}, volume = {123}, number = {1}, year = {2005}, month = {NOV}, pages = {50-52}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

The non-linear current (I)-voltage (V) characteristics of titanium dioxide doped with small quantities of tantalum and barium (99.9 TiO2 + 0.1 Ta and 99.4 TiO2 + 0.1 Ta + 0.5 Ba, all are in at.\%) were investigated. These samples have the non-linear coefficient (alpha) values of (20-30) with high breakdown voltages (E-B similar to 400-700 V mm(-1)). The pentavalent tantalum acts as donor and increases the electronic conductivity. The higher electrical conductivity and decrease in the breakdown field strength with barium addition is attributed to higher density. The acceptor like surface states formed by barium ions segregate to grain boundaries due size misfit to thereby modifying the electrical barrier characteristics of grain boundaries. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Oxides, TiO2, varistor, X-ray diffraction}, issn = {0921-5107}, doi = {10.1016/j.mseb.2005.06.015}, author = {Gaikwad, A. B. and Navale, SC and Ravi, V} } @article { ISI:000228510500016, title = {X-ray photoelectron spectroscopic investigations of Cu2O nanoparticles}, journal = {Materials Research Bulletin }, volume = {40}, number = {4}, year = {2005}, month = {APR}, pages = {694-700}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Cuprous oxide nanoparticles of five different sizes were obtained by electrochemical as well as chemical routes. Various capping agents were used to passivate the nanoparticles. X-ray diffraction studies show formation of single phased, cubic Cu2O nanoparticles. X-ray photoelectron spectroscopic studies indicate formation of CuO phase on the surface of Cu2O nanoparticles for uncapped as well as for those, capped by tetraoctylammonium bromide. On the other hand polyacrylamide and polyvinyl pyrrolidone capped samples did not show presence of CuO. X-ray photoelectron spectroscopy also indicates formation of a Cu2+ complex with the capping material on the surface of Cu2O nanoparticles. The results were discussed in terms of capability of passivation of various additives. (c) 2005 Elsevier Ltd. All rights reserved.

}, keywords = {Nanostructures, Oxides, photoelectron spectroscopy, Surfaces}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2004.12.008}, author = {Nikesh, V. V. and Mandale, A. B. and Patil, K. R. and Mahamuni, Shailaja} } @article { ISI:000241306000020, title = {Characterization of nanosized NiZn ferrite powders synthesized by an autocombustion method}, journal = {Materials Chemistry and Physics}, volume = {100}, number = {1}, year = {2006}, month = {NOV}, pages = {98-101}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Nanocrystalline Ni0.5Zn0.5Fe2O4 with average particle size of similar to 9 nm has been synthesized by an autocombustion method and characterized by powder XRD, TEM and room temperature magnetic measurements. High room temperature magnetization comparable to that of the bulk material is obtained for the nanosized powders annealed at 800 degrees C, with a maximum particle size of similar to 54 nm. The results show that optimum properties can be achieved for NiZn ferrite powders synthesized by the present autocombustion method and processed at relatively lower temperatures. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Magnetic materials, magnetic properties, Oxides}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2005.12.012}, author = {Deka, Sasanka and Joy, Pattayil Alias} } @article { ISI:000238298100027, title = {Co-precipitation technique for the preparation of ferroelectric BaBi2Ta2O9}, journal = {Materials Chemistry and Physics}, volume = {98}, number = {2-3}, year = {2006}, month = {AUG}, pages = {344-346}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

A simple co-precipitation technique had been successfully applied for the preparation of pure ultrafine single phase BaBi2Ta2O9 (BBT). Ammonium hydroxide and ammonium oxalate were used to precipitate Ba2+, Bi3+ and Ta5+ cations simultaneously. No pyrochlore phase was found while heating powder at 800 degrees C and pure BaBi2Ta2O9 phase was found to be formed by X-ray diffraction. Particle size and morphology was studied by transmission electron spectroscopy (TEM). The room temperature dielectric constant at 1 kHz is 350. The ferroelectric hysteresis loop parameters of these samples were also studied. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, electronic material, ferroelectricity, Oxides}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2005.09.036}, author = {Dhage, S. R. and Pasricha, R. and Murugan, A. Vadivel and Ravi, V.} } @article { ISI:000237439300005, title = {Coprecipitation technique to prepare NaNbO3 and NaTaO3}, journal = {Bulletin of Materials Science}, volume = {29}, number = {2}, year = {2006}, month = {APR}, pages = {123-125}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A simple coprecipitation technique has been used successfully for the preparation of pure, ultrafine, single phases of NaNbO3 (NN) and NaTaO3 (NT). An alcoholic solution of ammonium carbonate and ammonium hydroxide was used to precipitate Na+ and Nb5+ (or Ta5+) cations under basic conditions as carbonate and hydroxide, respectively. On heating at 700 degrees C, these precursors produce respective products. For comparison, both NN and NT powders were also prepared by the traditional solid state method. The phase purity and lattice parameters were studied by powder X-ray diffraction (XRD). The particle size and morphology were studied by scanning electron microscopy (SEM).

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, electronic materials, Oxides, X-ray methods}, issn = {0250-4707}, doi = {10.1007/BF02704604}, author = {Samuel, V and Gaikwad, A. B. and Ravi, V} } @article { ISI:000238866300004, title = {Coprecipitation technique to prepare Sr0.5Ba0.5Nb2O6}, journal = {Bulletin of Materials Science}, volume = {29}, number = {3}, year = {2006}, month = {JUN}, pages = {221-223}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

An aqueous mixture of ammonium oxalate and ammonium hydroxide was used to coprecipitate barium and strontium ions as oxalates and niobium ions as hydroxide under basic conditions. This precursor on calcining at 750 degrees C yielded Sr0.5Ba0.5Nb2O6 phase. This is a much lower temperature than that prepared by traditional solid state method (1000 degrees C) as reported for the formation of Sr0.5Ba0.5Nb2O6 (SBN). Transmission electron microscopic (TEM) investigations revealed that the average particle size was 80 nm for the calcined powders. The room temperature dielectric constant at I kHz was found to be 1100. The ferroelectric hysteresis loop parameters of these samples were also studied.

}, keywords = {Ceramics, Electron microscopy, ferroelectricity, Oxides, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02706488}, author = {Murugan, A. Vadivel and Gaikwad, A. B. and Samuel, V. and Ravi, V.} } @article { ISI:000237158200003, title = {Phase evolution of NiTiO3 prepared by coprecipitation method}, journal = {Materials Letters}, volume = {60}, number = {15}, year = {2006}, month = {JUL}, pages = {1791-1792}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple coprecipitation technique was used for the preparation of NiTiO3 powders. Ammonium carbonate solution was added to a solution mixture containing stoichiometric amounts of Ni(NO3)(2) and TiOCl2 to precipitate nickel as carbonate and titanium as hydroxide under basic conditions. The precipitate was calcined at different temperatures ranging from 100 to 800 degrees C and phase evolution of NiTiO3 was investigated by X-ray diffraction (XRD) studies. It is observed that nickel titanate was formed at 750 degrees C. For comparison, NiTiO3 was also prepared by standard ceramic process. Particle size and morphology was studied by transmission electron microscopy (TEM). (c) 2005 Elsevier B.V. All fights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, NiTiO3, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.12.023}, author = {Murugan, A. Vadivel and Samuel, V. and Navale, S. C. and Ravi, V.} } @article { ISI:000244008300030, title = {Co-precipitation technique to prepare BaTa2O6}, journal = {Ceramics International}, volume = {33}, number = {2}, year = {2007}, month = {JAN}, pages = {297-299}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A mixture of ammonium oxalate and ammonium hydroxide was used to co-precipitate barium and tantalum ions as barium oxalate and tantalum hydroxide under basic conditions. On calcination at 750 degrees C, this precursor yielded BaTa2O6 (BT) ceramics. This is much lower temperature as compared to that prepared by traditional solid-state method (1000 degrees C) as reported for the formation of BaTa206. Transmission electron microscope (TEM) investigations revealed that the average particle size is 70 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 100. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {barium tantalate, Ceramics, Electron microscopy, Oxides, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.08.012}, author = {Navale, S. C. and Samuel, Violet and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000246158300001, title = {Coprecipitation technique to prepare CoTa2O6 and CoNb2O6}, journal = {Materials Letter}, volume = {61}, number = {11-12}, year = {2007}, month = {MAY}, pages = {2127-2129}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

An aqueous solution of sodium hydroxide was used to coprecipitate cobalt and tantalum (or niobium) ions from their precursors as hydroxides under basic conditions. This precipitate yielded CoTa2O6 (CT) or CoNb2O6 (CN) ceramics on calcining at 700 degrees C, i.e. at a temperature much lower than 900 degrees C, reported for the formation of these powders prepared by the traditional solid state method. The X-ray diffraction (XRD) studies were employed to investigate phase contents and lattice parameters. The morphology of the synthesized powders was investigated by transmission electron microscopy (TEM). (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, electronic materials, Oxides, X-ray methods}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.08.024}, author = {Mulla, Imtiaz S. and Natarajan, N. and Gaikwad, A. B. and Samuel, V. and Guptha, U. N. and Ravi, V.} } @article { ISI:000246158300058, title = {Coprecipitation technique to prepare NiNb2O6}, journal = {Materials Letter}, volume = {61}, number = {11-12}, year = {2007}, month = {MAY}, pages = {2354-2355}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A mixture of ammonium carbonate and ammonium hydroxide was used to coprecipitate nickel and niobium ions as nickel carbonate and niobium hydroxide under basic conditions. This precursor yielded NiNb2O6 (NN) ceramics on calcining at 700 degrees C (at a temperature lower than 800 degrees C which is necessary for the formation of NiNb2O6 when prepared by the traditional solid state method). The average particle size and morphology of these powders were investigated by transmission electron microscope (TEM). (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, Oxides, X-ray methods}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.09.010}, author = {Samuel, V. and Gaikwad, A. B. and Jadhav, A. D. and Natarajan, N. and Ravi, V.} } @article { ISI:000246260000011, title = {Preparation of nanocrystalline ferroelectric CaBi4Ti4O15 by citrate gel method}, journal = {Ceramics International}, volume = {33}, number = {4}, year = {2007}, month = {JAN}, pages = {569-571}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A gel was formed when an aqueous solution of CaCl2, BiNO3, TiOCl2 and citric acid in stoichiometric ratio is heated on a water bath. This gel on decomposition at 700 degrees C produced nano crystallites of the ternary oxide, CaBi4Ti4O15 (CBT). The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology was studied by transmission electron spectroscopy (TEM). The room temperature dielectric constant at 1 kHz is 390. The ferroelectric hysteresis loop parameters of these samples were also studied by a home-built Sawyer-tower circuit. (c) 2006 Elsevier Ltd and Techna Group S.H. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray methods}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.11.006}, author = {Murugan, A. Vadivel and Gaikwad, A. B. and Samuel, V. and Ravi, V.} } @article {34}, title = {Stabilization of gamma-sterilized biomedical polyolefins by synergistic mixtures of oligomeric stabilizers. part II. polypropylene matrix}, journal = {Polymer Degradation and Stability}, volume = {92}, number = {2}, year = {2007}, month = {FEB}, pages = {299-309}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, author = {Alariqi, Sameh A. S. and Kumar, A. Pratheep and Rao, B. S. M. and Singh, R. P.} } @article { ISI:000248175000038, title = {Synthesis of La0.7Sr0.3MnO3 at 800 degrees C using citrate gel method}, journal = {Ceramics International}, volume = {33}, number = {6}, year = {2007}, month = {AUG}, pages = {1129-1132}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

Manganite systems have been of considerable interest in the recent past due to their potential to operate in wide property range and also to serve as effective magnetic sensing and storing devices when synthesized using stringent conditions. We report a novel citrate gel method, in which La0.7Sr0.3MnO3 system has been synthesized at temperature 800 degrees C (LSMO800) with the synthesis duration is 6 h. The results have been compared with the sample synthesized at 1050 degrees C (LSMO1050). The synthesized bulk polycrystalline sample shows single-phase nature with the increase in particle size from similar to 50 nm to 300 nm with the increase in the sintering temperature. The magnetization data for LSMO800 shows well-defined hysteresis with saturation magnetization at around 1800 Oe and Curie temperature at 360 K, which is slightly lower than that of LSMO1050, which is 375 K. The results can be well attributed to the grain boundary effects. (C) 2006 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {Ceramics, Citrate gel method, CMR, Oxides}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2006.02.008}, author = {Ravi, V. and Kulkarni, S. D. and Samuel, V. and Kale, Sangeeta N. and Mona, J. and Rajgopal, R. and Daundkar, A. and Lahoti, P. S. and Joshi, Rakesh S.} } @article { ISI:000244008300031, title = {Varistors based on Ta-doped TiO2}, journal = {Ceramics International}, volume = {33}, number = {2}, year = {2007}, month = {MAR}, pages = {301-303}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

The nonlinear current (I)-voltage (V) characteristics of titanium dioxide are examined when doped with small quantities (0.05-0.5 at.\%) of tantalum pentaoxide. For optimum compositions, the nonlinear coefficients are found to be in the range of 25-30 and the breakdown field strength (EB) is similar to 4000 V/cm. The obtained alpha- and E-B-values are higher than the previously reported values for TiO2 ceramics. The acceptor like surface states at the grain boundary adsorb oxygen during sintering and cooling, leading to formation of grain boundary barrier. The grain boundary barrier height (OB) is calculated using Schottky equation. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {Ceramics, Oxides, Schottky barrier, TiO2, varistor}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.07.026}, author = {Navale, S. C. and Murugan, A. Vadivel and Ravi, V.} } @article { ISI:000254698300035, title = {Co-precipitation method for preparation of Bi3TiNbO9 powders}, journal = {Ceramics International}, volume = {34}, number = {3}, year = {2008}, month = {APR}, pages = {675-677}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A simple co-precipitation technique has been successfully used for the preparation of pure, ultrafine, single phase Bi3TiNbO9 (BTN). An aqueous ammonium hydroxide solution was used to simultaneously precipitate Bi3+, Ti4+ and Nb5+, cations as hydroxides under basic conditions (pH similar to 9). No pyrochlore phase was found while heating powder at 500 degrees C and pure BTN phase was found to be formed by X-ray diffraction (XRD). For comparison, BTN samples were also synthesized by the traditional solid state method. The sequence of phase formation in both cases were investigated by XRD studies. (c) 2007 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, electronic material, Oxides, XRD}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2007.02.002}, author = {Gupta, U. N. and Samuel, V. and Muthurajan, H. and Kumar, H. H. and Patil, S. D. and Ravi, V.} } @article { ISI:000257538200034, title = {Co-precipitation technique to prepare BiNbO4 powders}, journal = {Ceramics International}, volume = {34}, number = {6}, year = {2008}, month = {AUG}, pages = {1565-1567}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A simple co-precipitation technique was successfully used for the preparation of pure ultrafine single phase BiNbO4. A standard ammonium hydroxide solution was used to precipitate Bi3+ and Ta5+ cations as hydroxides simultaneously under basic conditions. For comparison, BN powders were also prepared by the traditional solid-state method. It is observed that the co-precipitation technique produces BiNbO4 on heating at 600 degrees C, whereas complete phase formation occurs only at 800 degrees C in the solid-state method. The phase contents and lattice parameters were Studied by powder X-ray diffraction (XRD). (C) 2007 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {BiNbO4, Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2007.03.022}, author = {Radha, R. and Gupta, U. N. and Samuel, V. and Muthurajan, H. and Kumar, H. H. and Ravi, V.} } @article { ISI:000252408000041, title = {Co-precipitation technique to prepare BiTaO4 powders}, journal = {Materials Letters}, volume = {62}, number = {3}, year = {2008}, month = {FEB}, pages = {501-503}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple co-precipitation technique has been successfully used for the preparation of pure ultrafine single phase BiTaO4. A standard ammonium hydroxide solution was used to precipitate Bi3+ and Ta5+ cations as hydroxides simultaneously under basic conditions. This precursor, on heating at 600 degrees C, produced product phase. This is the lowest temperature for the formation of BiTaO4 phase so far reported in the literature. For comparison BiTaO4 powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). (c) 2007 Elsevier B.V. All rights reserved.

}, keywords = {BiTaO4, Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.05.074}, author = {Muthurajan, H. and Gupta, U. N. and Rituraj, B. and Rao, N. Koteswara and Pradhan, Sivaram and Radha, R. and Ravi, V.} } @article { ISI:000259420300006, title = {Facile synthesis and gas sensing properties of nanotriangular tin oxide}, journal = {Materials Letters}, volume = {62}, number = {28}, year = {2008}, month = {NOV}, pages = {4328-4331}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

In the present study we report a simple and convenient chemical route using pentaerythritol as a structure-directing agent for the synthesis of crystalline nanotriangular SnO2. We propose the scheme for the formation of nanotriangular structures wherein the preliminary spherical nanocrystallites are formed due to the low surface energy associated with them. These spherical nanocrystallites grow into the various linear intermediate shapes like Y, bi and tripods, which finally lead to the triangles, pyramids and bipyramids. Such variation in the structure occurs due to the structure directing pentaerythritol. These polycrystalline SnO2 nanomaterials with structural peculiarities were tested for the gas sensing characteristics. Their response towards ethanol vapor, H-2 and LPG were investigated. It was found to exhibit high response towards ethanol vapors at the operating temperature of 250 degrees C. (C) 2008 Elsevier B.V. All rights reserved.

}, keywords = {Nanomaterials, Oxides, Semiconductors, sensors}, issn = {0167-577X}, doi = {10.1016/j.matlet.2008.07.021}, author = {Deshmukh, Rupali G. and Badadhe, Satish S. and Vaishampayan, Mukta V. and Mulla, Imtiaz S.} } @article { ISI:000254820000016, title = {La0.67Ce0.03Sr0.3MnO3-coupled microwave assisted ultra-fast synthesis of nanocrystalline cobalt oxide and Bismuth oxide}, journal = {Materials Letters}, volume = {62}, number = {10-11}, year = {2008}, month = {APR}, pages = {1511-1513}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Bismuth hydroxide and Cobalt hydroxide gels were freshly prepared by adding aqueous sodium hydroxide to their corresponding nitrates under basic conditions. Then they were oven dried at 373 K and found to be amorphous in X-ray diffraction (XRD) study. They crystallized into their respective oxides by microwave irradiation (2.45 GHz) in merely 2 min using La0.67Ce0.03Sr0.3MnO3 (LCSMO) as couplant in a microwave domestic oven (similar to 100 W). This is the lowest temperature treatment and synthesis time so far reported in the literature for the formation of these systems. Formation of nanocrystallites of Bi2O3 (10 nm) and Co3O4 (15 nm) has been confirmed by XRD. Normally these hydroxides produce oxides only on heating at temperature \>673 K or digesting them at 373 K for 4 - 6 hours as reported by us earlier. Microwave assisted heating proves to be a novel technology whose applications can be carefully harnessed due to its unique effects compared to the conventional heating, such as rapid volumetric heating, shortened reaction time and energy saving. (C) 2007 Elsevier B.V. All rights reserved.

}, keywords = {Citrate gel method, Manganites, Microwave, Oxides}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.09.013}, author = {Rajagopal, Rajashree and Mona, J. and Joshi, Rakesh S. and Kale, Sangeeta N. and Pradhan, Sivararn and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000257367100016, title = {Low temperature synthesis and characterization of BiNbO4 powders}, journal = {Materials Characterization}, volume = {59}, number = {8}, year = {2008}, month = {AUG}, pages = {1083-1087}, publisher = {ELSEVIER SCIENCE INC}, address = {360 PARK AVE SOUTH, NEW YORK, NY 10010-1710 USA}, abstract = {

BiNbO4 powders, a potential microwave dielectric ceramic were prepared by both coprecipitation and solid state techniques. In the former method, an aqueous ammonium hydroxide was used to precipitate Bi3+ and Ta5+ cations as hydroxides simultaneously under basic conditions. It is observed that the co-precipitation produces BiNbO4 phase on heating at 600 degrees C, whereas complete phase formation occurs only at 800 degrees C in the case of solid state method. The phase contents and lattice parameters were studied by powder X-ray diffraction. The sequence of the reaction and phase evolution of BiNbO4 were also studied by the X-ray diffraction. The samples were characterized by the differential-thermal/thermo-gravimetric analyses and scanning electron microscopy techniques. (C) 2007 Elsevier Inc. All rights reserved.

}, keywords = {BiNbO4, Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {1044-5803}, doi = {10.1016/j.matchar.2007.08.026}, author = {Radha, R. and Muthurajan, H. and Rao, N. Koteswara and Pradhan, Sivaram and Gupta, U. N. and Jha, Ratnesh Kumar and Mirji, S. A. and Ravi, V.} } @article { ISI:000261361900032, title = {Low temperature synthesis of nanocrystalline lithium ferrite by a modified citrate gel precursor method}, journal = {Materials Research Bulletin}, volume = {43}, number = {12}, year = {2008}, month = {DEC}, pages = {3447-3456}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Single phase nanocrystalline lithium ferrite is synthesized by a modified citrate gel precursor technique. Ferrite nanoparticles of average size of 8 nm, obtained after calcination of the citrate gel Made by the usual method at 450 degrees C, show superparamagnetic behavior. However, small amounts of alpha-Fe(2)O(3) is formed as an impurity phase clue to the initial formation of some gamma-Fe(2)O(3) phase. Oil the other hand, when the pH of the mixed Solution is increased to 7 after the addition of ammonia Solution, a lower calcination temperature of 200 degrees C is sufficient for the formation of single phase lithium ferrite nanoparticles of size 30 nm. No impurity phases are detected when the nanocrystalline powders arc calcined at higher temperatures. The magnetic properties of the ferrite nanoparticles of different sizes obtained by calcining the powders at different temperatures are studied. (C) 2008 Elsevier Ltd. All rights reserved.

}, keywords = {Chemical synthesis, Magnetic materials, magnetic properties, Nanostructures, Oxides}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2008.01.023}, author = {Verma, Seema and Joy, Pattayil Alias} } @article { ISI:000251870400005, title = {Microwave assisted low temperature rapid synthesis of manganite system using La0.67Ce0.03Sr0.3MnO3 mini-cavity furnace}, journal = {Materials Letters}, volume = {62}, number = {2}, year = {2008}, month = {JAN}, pages = {191-193}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Amorphous La0.7Sr0.3MnO3 (LSMO) and La0.7Ca0.3MnO3 (LCMO) precursor powders synthesized by the citrate gel method at 673 K, have been found to crystallize by microwave irradiation in just 60 s using La0.67Ce0.03Sr0.3MnO3 (Ce-LSMO) as couplant. This is the lowest temperature treatment and synthesis time so far reported in literature for the fort-nation of manganite systems. Using ceramic route, the same amorphous samples crystallize on heat treatment only at temperatures greater than 1000 K. The microwave heating through this method is novel and has tremendous potential for accelerating the evolution of the product phase in very shorter durations, with just low temperature processing of the precursors, which cannot be realized in normal process. (c) 2007 Elsevier B.V. All rights reserved.

}, keywords = {Citrate gel method, LSMO, Manganites, Microwave, Oxides}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.05.002}, author = {Kale, Sangeeta N. and Rajagopal, Rajashree and Mona, J. and Londhe, D. P. and Joshi, Rakesh S. and Jagadale, Tushar C. and Satyanarayana, C. and Ravi, V.} } @article { ISI:000257365900027, title = {Novel hydroxide precursors for low temperature synthesis of selected ternary oxides}, journal = {Materials Research Bulletin}, volume = {43}, number = {7}, year = {2008}, month = {JUL}, pages = {1842-1849}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A novel method of using hydroxide precursors to reduce the synthesis temperature for few selected ternary oxides has been presented here. This technique is very useful and advantageous when the ternary oxides contain an alkaline earth element. The selected compositions for this method are BaCeO3 (BC), BaBiO3 (BB), La0.7Sr0.3CoO3 (LSCO) and BaBi2Nb2O9 (BBN). Commercially purchased strontium (or barium) hydroxide and freshly prepared lanthanum, cobalt, bismuth and niobium hydroxides were mixed thoroughly in stoichiometric ratio and heated at different temperatures ranging from 100 to 700 degrees C for 10 h for corresponding compositions. The sequence of the reaction and evolution of the product phase were studied by the X-ray diffraction (XRD) studies. The phase purity and lattice parameters were also determined by XRD investigations. All the product phases in each case were formed at relatively low temperature than when they were prepared by co-precipitation or solid state method. The morphology and average particle size of these powders were investigated by scanning electron microscopy (SEM). (C) 2007 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2007.07.006}, author = {Muthurajan, H. and Rao, N. Koteswara and Gupta, U. N. and Pradhan, Sivaram and Jha, Ratnesh Kumar and Kumar, H. H. and Mirji, S. A. and Ravi, V.} } @article { ISI:000255612400002, title = {Preparation of ferroelectric CaBi(4)Ti(4)O(15) powders from novel hydroxide precursors}, journal = {Materials Letters}, volume = {62}, number = {12-13}, year = {2008}, month = {APR}, pages = {1751-1753}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Ferroelectric CaBi(4)Ti(4)O(15) (CBT) powders were prepared for the first time from their respective hydroxides. Commercially purchased Ca(OH)(2) is mixed thoroughly with freshly prepared Bi(OH)(3) and Ti(OH)(4) in stoichiometrie ratio and heated at different temperatures ranging from 100 to 600 degrees C. The CBT phase found to be formed at 500 degrees C by the X-ray diffraction studies. This is the lowest temperature so far reported in the literature for the formation of CBT phase. The advantage of this method is that it also avoids the formation of calcium carbonate phase during synthesis. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD) method. The average particle size and morphology were studied by scanning electron microscopy (SEM) technique. (c) 2007 Elsevier B.V All rights reserved.

}, keywords = {CaBi(4)Ti(4)O(15), Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray methods}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.09.080}, author = {Deshmukh, Rupali G. and Vaishampayan, Mukta V. and Darshane, Sonali L. and Mulla, Imtiaz S. and Gaikwad, A. B. and Rao, N. Kotaserwara and Ravi, V.} } @article { ISI:000252408000048, title = {Synthesis of LSMO at low temperature by novel hydroxide precursor technique}, journal = {Materials Letters}, volume = {62}, number = {3}, year = {2008}, month = {FEB}, pages = {527-529}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A novel technique of mixing individual hydroxide is employed to prepare La0.65Sr0.35MnO3 (LSMO) at low temperature. Freshly prepared lanthanum and manganese hydroxides are mixed thoroughly with strontium hydroxide in stoichiometric ratio and heated at different temperatures ranging from 100 to 500 degrees C for 6 h. At 500 degrees C, formation of La0.65Sr0.35MnO3 was confirmed by the X-ray diffraction studies (XRD). This is the lowest temperature so far reported in the literature. The particle size and morphology were investigated by scanning electron microscopy (SEM). (c) 2007 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, La0.65Sr0.35MnO3, Oxides, Precipitation, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.05.077}, author = {Gupta, U. N. and Muthurajan, H. and Kumar, H. H. and Rao, N. Koteswara and Gokhale, Suresh P. and Ravi, V.} } @article { ISI:000263353200007, title = {Microwave dielectric and attenuation properties of Ni0.7-xCoxZn0.3Fe2O4 thick films}, journal = {Microelectronics International}, volume = {26}, number = {1}, year = {2009}, month = {JAN}, pages = {43-46}, publisher = {EMERALD GROUP PUBLISHING LIMITED}, address = {HOWARD HOUSE, WAGON LANE, BINGLEY BD16 1WA, W YORKSHIRE, ENGLAND}, abstract = {

Purpose - The aim of this paper is to investigate permittivity of nano structured Ni0.7-xCoxZn0.3Fe2O4 thick films at microwave frequencies. Design/methodology/approach - Nanosized Ni0.7-xCoxZn0.3Fe2O4 ferrites with x = 0, 0.04, 0.08 and 0.12 were prepared by sucrose precursor technique using the constituent metal nitrates. Thick films of the ferrites were fabricated on alumina substrates by screen-printing technique. Microwave dielectric constant (epsilon{\textquoteright}) and the loss factor (epsilon {\textquoteleft}{\textquoteright}) for the thick films were measured by VSWR slotted section method in the 8-18 GHz range of frequencies. Microwave attenuation properties were studied using a waveguide reflectometer set up. Findings - Both the epsilon{\textquoteright} and epsilon {\textquoteleft}{\textquoteright} were found to vary with frequency and composition x It is observed that, value of epsilon{\textquoteright} increases with increase in x, due to the increase in bulk density and reduction in porosity of the material, that resulted due to the substitution of cobalt in Ni-Zn ferrite. The microwave transmission loss offered by the thick films was found to increase with the increase in cobalt concentration x Within the band width of 4 GHz (from 12-16 GHz), all the films except that with x = 0.04 offered the reflection loss of less than 3 dB. Originality/value - The dielectric constant of Ni0.7-xCoxZn0.3Fe2O4 thick films have been reported for the first time. These thick films provide scope for cost effective planar ferrite devices.

}, keywords = {Microwaves, Oxides, Thick-film circuits}, issn = {1356-5362}, doi = {10.1108/13565360910923160}, author = {Rendale, M. K. and Kulkarni, S. D. and Puri, Vijaya} } @article { ISI:000264969200041, title = {Microwave-assisted synthesis and humidity sensing of nanostructured alpha-Fe2O3}, journal = {Materials Research Bulletin}, volume = {44}, number = {5}, year = {2009}, month = {MAY}, pages = {1179-1182}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Nanocrystalline alpha-Fe2O3 has been prepared on a large-scale by a facile microwave-assisted hydrothermal route from a solution of Fe(NO3)(3)center dot 9H(2)O and pentaerythritol. A systematic study of the morphology, crystallinity and oxidation state of Fe using different characterization techniques. Such as transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy was performed It reveals. that nanostructured alpha-Fe2O3 comprises bundles of nanorods with a rhombohedral crystalline Structure. The individual nanorod has 8-10 nm diameter and similar to 50 nm length. The as-prepared nanostructured alpha-Fe2O3 (sensor) gives selective response towards humidity. The sensor shows high sensitivity, fast linear response to change in the humidity with almost 100\% reproducibility. The sensor works at room temperature and rejuvenates without heat treatment. The as-prepared nanostructured alpha-Fe2O3 appears to be a promising humidity sensing material with the potential for commercialization. (C) 2008 Elsevier Ltd. All rights reserved.

}, keywords = {Chemical synthesis, Electrical properties, Nanostructures, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2008.09.044}, author = {Deshmukh, Rupali G. and Badadhe, Satish S. and Mulla, Imtiaz S.} } @article { ISI:000281175500059, title = {Simple chemical co-precipitation/calcination route for the synthesis of simulated synroc-B and synroc-C powders}, journal = {Materials Chemistry and Physics}, volume = {123}, number = {2-3}, year = {2010}, month = {OCT}, pages = {695-699}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

A simple chemical co-precipitation/calcination route was developed for the synthesis of simulated synroc-B and synroc-C powders using mostly nitrate salts as starting chemicals and 20\% ammonia solution as precipitant. In this route, a mixed solution containing Al-nitrate, Ca-nitrate, Ba-nitrate, zirconyl nitrate and titanyl nitrate in the molar proportion required for synroc-B is added to dilute ammonia solution to precipitate these cations in the form of their hydroxides at room temperature by maintaining pH approximate to 10.5 during precipitation. Formation of a major fluorite phase with minor amounts of anatase, rutile and hollandite phases is observed in the powder obtained after calcination in air at 750 degrees C. Multiphase crystalline synroc-B matrix containing hollandite, perovskite, zirconolite, and rutile phases is obtained after sintering the heat treated powder in the form of pellets at 1230 degrees C for 4h in air. Similarly, pure synroc-C phases with 14 and 20\% simulated waste loadings were synthesized following the same synthesis protocol. These pre-treated powders with a high surface area of similar to 25 m(2) g(-1) gave sintered ceramics having density of similar to 90\% for 14 and 20\% waste loadings. (C) 2010 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Oxides, Sintering}, issn = {0254-0584}, doi = {10.1016/j.matchemphys.2010.05.039}, author = {Potdar, H. S. and Vijayanand, S. and Mohaideen, Kamal Khaja and Patil, K. R. and Joy, Pattayil Alias and Madhavan, R. Raja and Kutty, K. V. G. and Ambashta, Ritu D. and Wattal, P. K.} } @article { ISI:000281347500022, title = {Surface texture and specific adsorption sites of sol-gel synthesized anatase TiO2 nanoparticles}, journal = {Materials Research Bulletin}, volume = {45}, number = {10}, year = {2010}, month = {OCT}, pages = {1470-1475}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

The surface properties of sot-gel synthesized anatase titania (TiO2) nanoparticles are probed by sorptiometry, infrared absorption spectroscopy, UV-vis diffuse reflectance spectroscopy and high resolution transmission electron microscopy. The results reveal strong correlations of the surface area, porosity, pyridine adsorption capacity and strength, and catalytic methylbutynol decomposition activity. (C) 2010 Elsevier Ltd. All rights reserved.

}, keywords = {Catalytic properties, Nanostructures, Oxides, Sol-gel chemistry, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2010.06.026}, author = {Zaki, Mohamed I. and Mekhemer, Gamal A. H. and Fouad, Nasr E. and Jagadale, Tushar C. and Ogale, Satishchandra B.} } @article { ISI:000289763700002, title = {Novel solar light driven photocatalyst, zinc indium vanadate for photodegradation of aqueous phenol}, journal = {Materials Research Bulletin}, volume = {46}, number = {5}, year = {2011}, month = {MAY}, pages = {635-638}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

In the present investigation, we have demonstrated the synthesis of novel photocatalyst, zinc indium vanadate (ZIV) by solid solid state route using respective oxides of zinc, indium and vanadium. This novel photocatalyst was characterized using XRD, FESEM, UV-DRS and FTIR in order to investigate its structural, morphological and optical properties. XRD clearly shows the formation of phase pure ZIV of triclinic crystal structure with good crystallinity. FESEM micrographs showed the clustered morphology having particle size between 0.5 and 1 mu m. Since, optical study showed the band gap around 2.8 eV, i.e. in visible region, we have performed the photocatalytic activity of phenol degradation under visible light irradiation. The photodecomposition of phenol by ZIV is studied for the first time and an excellent photocatalytic activity was obtained using this novel photocatalyst. Considering the band gap of zinc indium vanadate in visible region, it will also be the potential candidate for water splitting. (C) 2011 Elsevier Ltd. All rights reserved.

}, keywords = {Catalytic properties, Chemical synthesis, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2011.02.005}, author = {Mahapure, Sonali A. and Rane, Vilas H. and Ambekar, Jalindar D. and Nikam, Latesh K. and Marimuthu, R. and Kulkarni, Milind V. and Kale, Bharat B.} } @article { ISI:000305112000030, title = {Novel microwave assisted sol-gel synthesis (MW-SGS) and electrochromic performance of petal like h-WO3 thin films}, journal = {Materials Research Bulletin}, volume = {47}, number = {7}, year = {2012}, month = {JUL}, pages = {1787-1793}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Use of domestic microwave oven is first time employed for chemical deposition of nanocrystalline hexagonal WO3 (h-WO3) thin films. Low cost precursors like sodium tungstate, hydrochloric acid, oxalic acid and potassium sulfate signifies cost effectiveness of this thin film fabrication route. Scanning electron microscopy images reveal formation of petal like nanodisks. A number of analytical techniques were used to characterize the WO3 petal like nanodisks, including X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX). X-ray photoelectron spectroscopy, FT-IR spectroscopy, Raman scattering spectroscopy, UV-visible spectrophotometry and cyclic voltammetry (CV). The X-ray photoelectron spectroscopic studies revealed 2.89 O/W atomic ratio. The electrical transport studies on WO3 thin films show semiconducting behavior with n-type semiconductivity. The value of determined coloration efficiency is 57.90 cm(2)/C. The mechanism of Li+ intercalation and deinercalation in h-WO3 matrix is proposed for enhanced electrochromism. (C) 2012 Elsevier Ltd. All rights reserved.

}, keywords = {Chemical synthesis, Electrochemical properties, Oxides, photoelectron spectroscopy}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2012.03.025}, author = {Kharade, Rohini R. and Patil, K. R. and Patil, P. S. and Bhosale, Popatrao N.} } @article { ISI:000324077700076, title = {Fungus mediated synthesis of biomedically important cerium oxide nanoparticles}, journal = {Materials Research Bulletin}, volume = {48}, number = {10}, year = {2013}, month = {OCT}, pages = {4134-4138}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Nanomaterials can be synthesized by chemical, physical and the more recently discovered biological routes. The biological routes are advantageous over the chemical and physical ones as unlike these, the biological synthesis protocols occur at ambient conditions, are cheap, non-toxic and eco-friendly. Although purely biological and bioinspired methods for the synthesis of nanomaterials are environmentally benign and energy conserving processes, their true potential has not been explored yet and attempts are being made to extend the formation of technologically important nanoparticles using microorganisms like fungi. Though there have been reports on the biosynthesis of oxide nanoparticles by our group in the past, no attempts have been made to employ fungi for the synthesis of nanoparticles of rare earth metals or lanthanides. Here we report for the first time, the bin-inspired synthesis of biomedically important cerium oxide (CeO2) nanoparticles using the thermophilic fungus Humicola sp. The fungus Humicola sp. when exposed to aqueous solutions of oxide precursor cerium (III) nitrate hexahydrate (CeN3O9 center dot 6H(2)O) results in the extracellular formation of CeO2 nanoparticles containing Ce (III) and Ce (IV) mixed oxidation states, confirmed by X-ray Photoemission Spectroscopy (XPS). The formed nanoparticles are naturally capped by proteins secreted by the fungus and thus do not agglomerate, are highly stable, water dispersible and are highly fluorescent as well. The biosynthesized nanoparticles were characterized by UV-vis spectroscopy, Photoluminescence spectroscopy (PL), Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD) and X-ray Photoemission Spectroscopy (XPS). (c) 2013 Elsevier Ltd. All rights reserved.

}, keywords = {Electron microscopy, Nanostuctures, Optical properties, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2013.06.038}, author = {Khan, Shadab Ali and Ahmad, Absar} } @article { ISI:000338605600002, title = {Influence of starting precursors and synthesis methods on the physiochemical properties of zirconia}, journal = {Materials Research Bulletin}, volume = {55}, year = {2014}, month = {JUL}, pages = {8-12}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Under identical and judiciously pre-optimized synthesis conditions, the influence of different combinations of zirconium sources and/or post treatment conditions on structural properties, thermal stability, phase composition and morphology of zirconia has been investigated. High surface area tetragonal zirconia could be synthesized in a cost-effective manner from 1 M solution of zirconium oxynitrate at pH 11 using aqueous ammonia solution as a precipitant when calcined at 400 degrees C for 3 h. Irrespective of the preparation method, pH and starting precursor, zirconia samples prepared without digestion contained dominant monoclinic phase with some traces of tetragonal phase when calcined at 700 degrees C. Even though there is linear decrease in surface area with increase in the crystallite size for each sample as a function of calcination temperature, no co-relation between the surface area and crystallite size could be achieved. SEM images show agglomerated and irregular shape particles between 10 to 20 mu m. (C) 2014 Elsevier Ltd. All rights reserved.

}, keywords = {Oxides, Sol-gel chemistry, Thermogravimetric analysis (TGA)}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2014.03.010}, author = {Gaydhankar, T. R. and Jha, Ratnesh Kumar and Nikalje, M. D. and Waghmare, K. J.} }