@article { ISI:000229811300003, title = {Coprecipitation technique to prepare ZnM2O6 powders}, journal = {Bulletin of Materials Science}, volume = {28}, number = {3}, year = {2005}, month = {JUN}, pages = {205-207}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A simple coprecipitation technique was successfully applied for the preparation of pure ultrafine single phase, ZnNb2O6 (ZN). Ammonium hydroxide was used to precipitate Zn2+ and Nb5+ cations as hydroxides simultaneously. This precursor on heating at 750 degrees, produced ZN powders. For comparison, ZN powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM).

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02711248}, author = {Deshpande, V. V. and Patil, M. M. and Navale, S. C. and Ravi, V.} } @article { ISI:000232864800029, title = {Low temperature synthesis of MgTa2O6 powders}, journal = {Materials Letters}, volume = {59}, number = {29-30}, year = {2005}, month = {DEC}, pages = {3926-3928}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A combination of digestion and further low temperature calcination to crystallize the product is employed to prepare MgTa2O6 (MT) ceramics. Freshly prepared niobium hydroxide gel is mixed with magnesium hydroxide thoroughly and allowed to react at 100 degrees C under refluxing and stirring conditions for 6-12 h. The X-ray amorphous product so formed is heated at 550 degrees C to form crystalline MgTa2O6. This is the lowest temperature so far reported for the formation of MgTa2O6. For comparison, MT powders were also prepared by the traditional solid state method. Transmission electron microscope (TEM) investigations revealed that the average particle size is 40 nm for the low temperature calcined powders. (C) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, magnesium tantalate, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.07.035}, author = {Navale, SC and Samuel, V and Ravi, V} } @article { ISI:000230275100022, title = {Preparation of nanocrystalline LiNbO3 by citrate gel method}, journal = {Materials Letters}, volume = {59}, number = {19-20}, year = {2005}, month = {AUG}, pages = {2476-2478}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A gel was formed when an aqueous solution of Li(NO3) NbF5 and citric acid in stoichiometric ratio is heated in a water bath at 100 degrees C. This gel on decomposition at 700 degrees C produced the fine crystallites of ternary oxide, LiNbO3 (LN). The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology was studied by transmission electron spectroscopy (TEM). (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, electronic materials, lithium niobate, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.03.028}, author = {Navale, SC and Samuel, V and Ravi, V} } @article { ISI:000229379000010, title = {Preparation of nanocrystalline MgNb2O6 by citrate gel method}, journal = {Materials Letters}, volume = {59}, number = {17}, year = {2005}, month = {JUL}, pages = {2146-2148}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A gel was formed when a aqueous solution of Mg(NO3)(2), NbF5 and citric acid in stoichiometric ratio is heated on a water bath. This gel on decomposition at 700 degrees C produced the fine crystallites of ternary oxide, MgNb2O6 (MN). The formation of MN phase and lattice parameters were determined by the powder X-ray diffraction (XRD). Particle size and morphology was studied by transmission electron spectroscopy (TEM). (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Citrate gel, Electron microscopy, magnesium niobate, powders, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.02.050}, author = {Pasricha, R and Ravi, V} } @article { ISI:000231605600002, title = {Preparation of ultrafine LiTaO3 powders by citrate gel method}, journal = {Bulletin of Materials Science}, volume = {28}, number = {5}, year = {2005}, month = {AUG}, pages = {391-393}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

A gel was formed when a aqueous solution of Li(NO3), TaF5 and citric acid in stoichiometric ratio was heated in a water bath. This gel on decomposition at 700 degrees C produced fine crystallites of ternary oxide, LiTaO3 (LT). The phase contents and lattice parameters were studied by powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM).

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02711224}, author = {Navale, SC and Samuel, V and Ravi, V} } @article { ISI:000230275100032, title = {Synthesis of bismuth oxide nanoparticles at 100 degrees C}, journal = {Materials Letters}, volume = {59}, number = {19-20}, year = {2005}, month = {AUG}, pages = {2523-2525}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple gel to crystal conversion route has been followed for the preparation of ultrafine Bi2O3 particles at 80-100 degrees C under refluxing conditions. Freshly prepared bismuth hydroxide gel is allowed to crystallize under refluxing and stirring conditions for 6-12 h. Formation of nanocrystallites of Bi2O3 is confirmed by X-ray diffraction (XRD) study. The thermal decomposition of bismuth hydroxide yields Bi2O3 only at 400 degrees C. This shows the advantage of the present method. Transmission electron microscope (TEM) investigations revealed that the average particle size is 50 nm for these oven-dried powders. (c) 2005 Elsevier B.V All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.03.037}, author = {Patil, M. M. and Deshpande, V. V. and Dhage, S. R. and Ravi, V.} } @article { ISI:000225588700025, title = {Synthesis of bismuth titanate by the urea method}, journal = {Materials Letters}, volume = {59}, number = {4}, year = {2005}, month = {FEB}, pages = {514-516}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple urea precipitation route was adopted for the preparation of bismuth titanate (Bi4Ti3O12) powders. Stoichiometric quantities of BiCl3 and TiOCl2 were mixed with the required amount of urea (the ratio of total metal cations to urea is five), and the mixture was heated on a water bath. This leads to the formation of precipitate, which was decomposed at 973 K. The formation of bismuth titanate was observed on calcining powders at 973 K by X-ray diffraction studies. The average particle size is found to be 100 nm by microscopy. The room temperature dielectric constant is found to be 150 at 1 kHz. The hysteresis loop parameters were also obtained by home-built Sawer-Tower circuit. (C) 2004 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, dielectric properties, ferroelectricity, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2004.10.038}, author = {Anilkumar, Mettu and Dhage, S. R. and Ravi, V.} } @article { ISI:000226803200008, title = {Synthesis of fine particles of ZnO at 100 degrees C}, journal = {Materials Letters}, volume = {59}, number = {7}, year = {2005}, month = {MAR}, pages = {779-781}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple gel to crystal conversion route has been followed for the preparation of fine ZnO at 80-100 degreesC under refluxing conditions. Freshly prepared zinc hydroxide gel is allowed to crystallize under refluxing and stirring conditions for 4-6 It. Formation of fine crystallites of ZnO is confirmed by X-ray diffraction (XRD) study. Transmission electron microscope (TEM) investigations revealed that the average particle size is 100 nm for these powders. (C) 2004 Elsevier B.V All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2004.11.019}, author = {Dhage, S. R. and Pasricha, R. and Ravi, V.} } @article { ISI:000228510500005, title = {Synthesis of nanocrystalline Mn3O4 at 100 degrees C}, journal = {Materials Research Bulletin}, volume = {40}, number = {4}, year = {2005}, month = {APR}, pages = {605-609}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A simple gel to crystal conversion route has been followed for the preparation of nanocrystalline tetragonal Mn3O4 powders at 80-100 degrees C under refluxing conditions. Freshly prepared manganese hydroxide gel is allowed to crystallize under refluxing and stirring conditions for 4-6 h. Formation of nano crystallites of Mn3O4 is confirmed by X-ray diffraction (XRD) study. Transmission electron microscope (TEM) investigations revealed that the average particle size is 50 nm for these powders. (c) 2005 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2005.01.009}, author = {Anilkumar, Mettu and Ravi, V.} } @article { ISI:000232196200008, title = {TiO2 ceramic varistor modified with tantalum and barium}, journal = {Materials Science and Engineering B-Solid State Materials for Advanced Technology}, volume = {123}, number = {1}, year = {2005}, month = {NOV}, pages = {50-52}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

The non-linear current (I)-voltage (V) characteristics of titanium dioxide doped with small quantities of tantalum and barium (99.9 TiO2 + 0.1 Ta and 99.4 TiO2 + 0.1 Ta + 0.5 Ba, all are in at.\%) were investigated. These samples have the non-linear coefficient (alpha) values of (20-30) with high breakdown voltages (E-B similar to 400-700 V mm(-1)). The pentavalent tantalum acts as donor and increases the electronic conductivity. The higher electrical conductivity and decrease in the breakdown field strength with barium addition is attributed to higher density. The acceptor like surface states formed by barium ions segregate to grain boundaries due size misfit to thereby modifying the electrical barrier characteristics of grain boundaries. (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Oxides, TiO2, varistor, X-ray diffraction}, issn = {0921-5107}, doi = {10.1016/j.mseb.2005.06.015}, author = {Gaikwad, A. B. and Navale, SC and Ravi, V} } @article { ISI:000234951400014, title = {Coprecipitation technique to prepare LiTaO3 powders}, journal = {Materials Letters}, volume = {60}, number = {8}, year = {2006}, month = {APR}, pages = {1047-1048}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple coprecipitation technique had been successfully applied for the preparation of pure ultrafine single phase LiTaO3 (LT). An aqueous mixture of ammonium carbonate and ammonium hydroxide was used to precipitate Li+ and Ta5+ cations as carbonate and hydroxide respectively. This precursor oil heating at 750 degrees C produces LT powders. For comparison, LT powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). Particle size and morphology were studied by transmission electron spectroscopy (TEM). (c) 2005 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.10.074}, author = {Navale, SC and Gaikwad, A. B. and Ravi, V} } @article { ISI:000238866300004, title = {Coprecipitation technique to prepare Sr0.5Ba0.5Nb2O6}, journal = {Bulletin of Materials Science}, volume = {29}, number = {3}, year = {2006}, month = {JUN}, pages = {221-223}, publisher = {INDIAN ACADEMY SCIENCES}, type = {Article}, address = {C V RAMAN AVENUE, SADASHIVANAGAR, P B \#8005, BANGALORE 560 080, INDIA}, abstract = {

An aqueous mixture of ammonium oxalate and ammonium hydroxide was used to coprecipitate barium and strontium ions as oxalates and niobium ions as hydroxide under basic conditions. This precursor on calcining at 750 degrees C yielded Sr0.5Ba0.5Nb2O6 phase. This is a much lower temperature than that prepared by traditional solid state method (1000 degrees C) as reported for the formation of Sr0.5Ba0.5Nb2O6 (SBN). Transmission electron microscopic (TEM) investigations revealed that the average particle size was 80 nm for the calcined powders. The room temperature dielectric constant at I kHz was found to be 1100. The ferroelectric hysteresis loop parameters of these samples were also studied.

}, keywords = {Ceramics, Electron microscopy, ferroelectricity, Oxides, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/BF02706488}, author = {Murugan, A. Vadivel and Gaikwad, A. B. and Samuel, V. and Ravi, V.} } @article {Rai, title = {Liquid phase oxidation of alkanes using Cu/Co-perchlorophthalocyanine immobilized MCM-41 under mild reaction conditions}, journal = {Applied Catalysis A-General}, volume = {297}, number = {2}, year = {2006}, month = {JAN}, pages = {220-230}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

{Amino-functionalized MCM-41 (NH2-MCM-41) was used to immobilize CU/CO-Cl16PC complex, i.e. Cu/Co-AM(PS) for liquid phase oxidation of alkanes under mild reaction conditions. Higher rates of reaction and better catalytic activity values were obtained for Cu/Co-AM(PS) as compared to Cu/Co-Cl16PC grafted on (i) amino-functionalized SiO2 [

}, keywords = {Ceramics, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.apcata.2005.09.012}, author = {Karandikar, Prashant R. and Chandwadkar, Asha J. and Agashe, M. and Ramgir, N. S. and Sivasanker, S.} } @article { ISI:000235439900024, title = {Low temperature route to prepare LaMnO3}, journal = {Materials Letters}, volume = {60}, number = {9-10}, year = {2006}, month = {MAY}, pages = {1213-1214}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A combination of digestion and further low temperature calcination to crystallize the product is employed to prepare LaMnO3(LM) ceramics. Freshly co-precipitated lanthanum and manganese hydroxides gel is allowed to react at 100 degrees C under refluxing and stirring conditions for 6-12 h. The X-ray amorphous product so formed is heated at 300 degrees C to form crystalline LM powders. This is the lowest temperature so far reported for the formation of LaMnO3. Transmission electron microscope (TEM) investigations revealed that the average particle size is 50 nm for the calcined powders. (c) 2005 Elsevier B.V All rights reserved.

}, keywords = {Chemical synthesis, LaMnO3, Precipitation, transmission electron microscopy, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.11.002}, author = {Daundkar, A. and Kale, Sangeeta N. and Gokhale, Suresh P. and Ravi, V} } @article { ISI:000238624000023, title = {Negative thermal expansion in silicalite-1 and zirconium silicalite-1 having MFI structure}, journal = {Materials Research Bulletin}, volume = {41}, number = {7}, year = {2006}, month = {JUL}, pages = {1392-1402}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

In situ high temperature X-ray diffraction (HTXRD) studies on monoclinic silicalite-1 (S-1, silica polymorph of ZSM-5) and an orthorhombic metallosilicate molecular sieve, zirconium silicalite-1 (ZrS-1) with MFI structure (Si/Zr = 50) have been carried out using a laboratory X-ray diffractometer with an Anton Parr HTK 1600 attachment. While the structure of the S-I collapsed at 1123 K forming alpha-cristobalite. S-1 and ZrS-1 showed a complex thermal expansion behavior in the temperature range 298-1023 K, ZrS-1 was stable. Powder X-ray diffraction (PXRD) data taken in this region have shown strong negative lattice thermal expansion coefficient, alpha(v) = -6.75 x 10(-6) and - 17.92 x 10(-6) K-1 in the temperature range 298-1023 K-1 for S-1 and ZrS-1 samples, respectively. The thermal expansion behavior of S-1 and ZrS-1 is anisotropic, with the relative strength of contraction along a axis is more than that along b and c axes. Three different thermal expansion regions could be identified in the overall temperature range (298-1023 K) studied, corroborating with the three steps of weight loss in the TG curve of ZrS-1 sample. While the region between 298 and 423 K, displays positive thermal expansion coefficient with alpha(v) = 2.647 x 10(-6) and 4.24 x 10(-6) K-1, the second region between 423 and 873 K shows strong negative thermal expansion (NTE) coefficient alpha(v) = -7.602 x 10(-6) and - 15.04 x 10(-6) K-1, respectively, for S-1 and ZrS-1 samples. The region between 873 and 1023 K, shows a very strong NTE coefficient with alpha(v) = - 12.08 x 10(-6) and -45.622 x 10(-6) K-1 for S-1 and ZrS-1, respectively, which is the highest in the whole temperature range studied. NTE seen over a temperature range 298-1023 K could be associated with transverse vibrations of bridging oxygen atoms in the structure which results in an apparent shortening of the Si-O distances. (C) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {microporous materials, phase transitions, Thermal expansion, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2005.12.002}, author = {Bhange, Deu S. and Ramaswamy, V.} } @article { ISI:000237158200003, title = {Phase evolution of NiTiO3 prepared by coprecipitation method}, journal = {Materials Letters}, volume = {60}, number = {15}, year = {2006}, month = {JUL}, pages = {1791-1792}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple coprecipitation technique was used for the preparation of NiTiO3 powders. Ammonium carbonate solution was added to a solution mixture containing stoichiometric amounts of Ni(NO3)(2) and TiOCl2 to precipitate nickel as carbonate and titanium as hydroxide under basic conditions. The precipitate was calcined at different temperatures ranging from 100 to 800 degrees C and phase evolution of NiTiO3 was investigated by X-ray diffraction (XRD) studies. It is observed that nickel titanate was formed at 750 degrees C. For comparison, NiTiO3 was also prepared by standard ceramic process. Particle size and morphology was studied by transmission electron microscopy (TEM). (c) 2005 Elsevier B.V. All fights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, NiTiO3, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2005.12.023}, author = {Murugan, A. Vadivel and Samuel, V. and Navale, S. C. and Ravi, V.} } @article { ISI:000241849900014, title = {Photoelectrochemical properties of electrochemically deposited CdIn2S4 thin films}, journal = {Journal of Physics and Chemistry of Solids}, volume = {67}, number = {11}, year = {2006}, month = {NOV}, pages = {2331-2336}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Thin films of CdIn2S4 have been deposited on to stainless steel and fluorine-doped tin oxide (FTO)-coated glass substrates from aqueous acidic bath using an electrodeposition technique. Ethylene diamine tetra-acetic acid (EDTA) disodium salt is used as complexing agent to obtain good-quality deposits by controlling the rate of the reaction. The different preparative parameters like concentration of bath, deposition time, bath temperature, pH of the bath have been optimized by the photoelectrochemical (PEC) technique in order to get good-quality photosensitive material. Different techniques have been used to characterize CdIn2S4 thin films. Optical absorption shows the presence of direct transition with band gap energy 2.17 eV. The X-ray diffraction (XRD) analysis of the as-deposited and annealed films showed the presence of polycrystalline nature. Energy-dispersive analysis by X-ray (EDAX) study for the sample deposited at optimized preparative parameters shows that the In-to-Cd ratio is almost 2 and S-to-Cd ratio is almost 4. Scanning electron microscopy (SEM) for samples deposited at optimized preparative parameters reveals that spherical grains are uniformly distributed over the surface of the substrate indicates the well-defined growth of polycrystalline CdIn2S4 thin film. PEC characterization of the films is carried out by studying photoresponse, spectral response and photovoltaic output characteristics. The fill factor (ff) and power conversion efficiency (eta) of the cell are 69 and 2.94\%, respectively. (c) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {Thin films, X-ray diffraction}, issn = {0022-3697}, doi = {10.1016/j.jpcs.2006.05.022}, author = {Kokate, A. V. and Asabe, M. R. and Delekar, S. D. and Gavali, L. V. and Mulla, Imtiaz S. and Hankare, P. P. and Chougule, B. K.} } @article { ISI:000238624000017, title = {Synthesis of MgNb2O6 by coprecipitation}, journal = {Materials Research Bulletin}, volume = {41}, number = {7}, year = {2006}, month = {JUL}, pages = {1353-1356}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A simple coprecipitation technique was used successfully to synthesize fine powders of MgNb2O6 (MN) phase. An aqueous mixture of ammonium carbonate and ammonium hydroxide was used to precipitate Mg2+ and Nb5+ cations as carbonate and hydroxide respectively under basic conditions. This precipitate on heating at 750 degrees C produced MN powders. For comparison MN powders were prepared by the traditional solid state method. The phase content and the lattice parameters were studied by powder X-ray diffraction (XRD). Particle size and morphology of the particles were studied by scanning electron microscopy (SEM). (C) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2005.12.009}, author = {Navale, S. C. and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000244008300030, title = {Co-precipitation technique to prepare BaTa2O6}, journal = {Ceramics International}, volume = {33}, number = {2}, year = {2007}, month = {JAN}, pages = {297-299}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A mixture of ammonium oxalate and ammonium hydroxide was used to co-precipitate barium and tantalum ions as barium oxalate and tantalum hydroxide under basic conditions. On calcination at 750 degrees C, this precursor yielded BaTa2O6 (BT) ceramics. This is much lower temperature as compared to that prepared by traditional solid-state method (1000 degrees C) as reported for the formation of BaTa206. Transmission electron microscope (TEM) investigations revealed that the average particle size is 70 nm for the calcined powders. The room temperature dielectric constant at 1 kHz is found to be 100. (c) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {barium tantalate, Ceramics, Electron microscopy, Oxides, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2005.08.012}, author = {Navale, S. C. and Samuel, Violet and Gaikwad, A. B. and Ravi, V.} } @article { ISI:000245760900020, title = {Low temperature route to prepare LaFeO3 and LaCoO3}, journal = {Materials Letters}, volume = {61}, number = {10}, year = {2007}, month = {APR}, pages = {2030-2032}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A combination of digestion and further low temperature calcination to crystallize the product was employed to prepare LaFeO3 (LF) and LaCoO3 (LC) powders. Freshly co-precipitated lanthanum and ferric (or cobalt) hydroxide gels by sodium hydroxide were allowed to react at 100 degrees C under refluxing and stirring conditions for 4-6 h. These oven dried powders were heated at 450 degrees C to from crystalline LF (or LC) powders. The phase contents and lattice parameters were investigated by X-ray diffraction (XRD). Transmission electron microscope (TEM) investigations were carried out to examine the morphology and average particle size of these powders. (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, LaFeO3, Precipitation, transmission electron microscopy, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.08.009}, author = {Jadhav, A. D. and Gaikwad, A. B. and Samuel, V. and Ravi, V.} } @article { ISI:000252474200009, title = {Low voltage varistor ceramics based on SnO2}, journal = {Bulletin of Materials Science}, volume = {30}, number = {6}, year = {2007}, month = {DEC}, pages = {583-586}, publisher = {SPRINGER}, type = {Article}, address = {233 SPRING STREET, NEW YORK, NY 10013 USA}, abstract = {

The nonlinear current (I)-voltage (V) characteristics of tin dioxide doped with either Nb2O5 and CoO or Sb2O3 and CoO show promising values of nonlinear coefficient (alpha) values (similar to 11) with low breakdown voltages (E-B, similar to 40 V mm(-1)). The pentavalent antimony or niobium acts as donor and increases the electronic conductivity. The crucial parameter for obtaining low breakdown voltage is the grain size, which depends upon sintering duration and temperature of these oxide ceramics.

}, keywords = {Chemical synthesis, electronic materials, Microstructure, tin oxide, X-ray diffraction}, issn = {0250-4707}, doi = {10.1007/s12034-007-0092-8}, author = {Dhage, S. R. and Ravi, V. and Yang, O. B.} } @article { ISI:000243164000035, title = {Novel technique to prepare LiNbO3 at low temperature}, journal = {Materials Letter}, volume = {61}, number = {3}, year = {2007}, month = {FEB}, pages = {765-766}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Fresh niobium hydroxide was first precipitated from NbF5 solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 degrees C) produced pure ultrafine single phase LiNbO3 (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM). (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, LiNbO3, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2006.05.056}, author = {Samuel, V. and Gaikwad, A. B. and Jadhav, A. D. and Mirji, S. A. and Ravi, V.} } @article {34}, title = {Stabilization of gamma-sterilized biomedical polyolefins by synergistic mixtures of oligomeric stabilizers. part II. polypropylene matrix}, journal = {Polymer Degradation and Stability}, volume = {92}, number = {2}, year = {2007}, month = {FEB}, pages = {299-309}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, author = {Alariqi, Sameh A. S. and Kumar, A. Pratheep and Rao, B. S. M. and Singh, R. P.} } @article { ISI:000243821700012, title = {Structural evolutions of hydrothermally prepared mesostructured MCM-48 silica using differently manufactured amorphous silica powders}, journal = {Journal of Non-Crystalline Solids}, volume = {353}, number = {2}, year = {2007}, month = {FEB}, pages = {194-199}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

The hydrothermal synthesis of Si-MCM-48 mesoporous molecular sieves was carried out using a ternary SiO2:CTAOH:H2O System wherein differently manufactured amorphous silica powders such as fumed silica (FMDS), spray dried precipitated silica (SDPS) and flash dried precipitated silica (FDPS) were used as silica source materials. The changes in structural/textural properties were evaluated using powder XRD, N-2 adsorption-desorption and scanning electron microscopy techniques. Studies on the progressive development of MCM-48 mesophases revealed that, the reactivity of the silica source follow the trend: FMDS \> SDPS \> FDPS. MCM-48 synthesized using low cost FDPS has exhibited thicker pore walls but poorer orderness, while MCM-48 prepared from relatively expensive FMDS has thinner pore walls and more ordered structure. Moreover, the extent of contraction caused by calcinations, agglomerate size and structural stability were found to depend on the reactivity of the silica source used. (c) 2006 Elsevier B.V. All rights reserved.

}, keywords = {long-range order, micelles, scanning electron microscopy, silica, silicates, sol-gels (xerogels), X-ray diffraction}, issn = {0022-3093}, doi = {10.1016/j.jnoncrysol.2006.10.005}, author = {Taralkar, U. S. and Jha, Ratnesh Kumar and Joshi, P. N.} } @article { ISI:000245842600009, title = {Thermal stability of the Mobil Five type metallosilicate molecular sieves - an in situ high, temperature X-ray diffraction study}, journal = {Materials Research Bulletin}, volume = {42}, number = {5}, year = {2007}, month = {MAY}, pages = {851-860}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

We have carried out in situ high temperature X-ray diffraction (HTXRD) studies of silicalite-1 (S-1) and metallosilicate molecular sieves containing iron, titanium and zirconium having Mobil Five (MFI) structure (iron silicalite-1 (FeS-1), titanium silicalite-1 (TS-1) and zirconium silicalite-1 (ZrS-1), respectively) in order to study the thermal stability of these materials. Isomorphous substitution of Si4+ by metal atoms is confirmed by the expansion of unit cell volume by X-ray diffraction (XRD) and the presence of Si-O-M stretching band at similar to 960 cm(-1) by Fourier transform infrared (FTIR) spectroscopy. Appearance of cristobalite phase is seen at 1023 and 1173 K in S-1 and FeS-1 samples. While the samples S-1 and FeS-1 decompose completely to cristobalite at 1173 and 1323 K, respectively, the other two samples are thermally stable upto 1623 K. This transformation is irreversible. Although all materials show a negative lattice thermal expansion, their lattice thermal expansion coefficients vary. The thermal expansion behavior in all samples is anisotropic with relative strength of contraction along {\textquoteleft}a{\textquoteright} axes is more than along {\textquoteleft}b{\textquoteright} and V axes in S- 1, TS-1, ZrS-1 and vice versa in FeS-1. Lattice thermal expansion coefficients (alpha(v)) in the temperature range 298-1023 K were -6.75 x 10(-6) K-1 for S-1, -12.91 x 10(-6) K-1 for FeS-1, -16.02 x 10(-6) K-1 for TS-1 and -17.92 x 10(-6) K-1 for ZrS-1. The highest lattice thermal expansion coefficients (alpha(v)) obtained were -11.53 x 10(-6) K-1 for FeS-1 in temperature range 298-1173 K, -20.86 x 10(-6) K-1 for TS-1 and -25.54 x 10(-6) K-1 for ZrS-1, respectively, in the temperature range 298-1623 K. Tetravalent cation substitution for Si4+ in the lattice leads to a high thermal stability as compared to substitution by trivalent cations. (c) 2006 Elsevier Ltd. All rights reserved.

}, keywords = {microporous materials, Thermal expansion, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2006.08.024}, author = {Bhange, Deu S. and Ramaswamy, Veda} } @article { ISI:000262796500004, title = {Characterization of MoSe2 thin film deposited at room temperature from solution phase}, journal = {Journal of Crystal Growth}, volume = {311}, number = {1}, year = {2008}, month = {DEC}, pages = {15-19}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple, low-temperature method has been developed to synthesis molybdenum diselenide semiconductor thin films, based on the chemical reaction of conlplexed ammonium molybdate, hydrazine hydrate and sodium Selenosulphate in aqueous alkaline medium. The deposition parameter of the MoSe2 thin film is interpreted in the present investigation. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption and electrical measurements. The deposited film was found to be polycrystalline in hexagonal form. The direct band gap {\textquoteleft}E-g{\textquoteright} for the film was found to be 1.43eV and electrical conductivity in the order of 10(-2)(Omega cm)(-1) with n-type conduction mechanism. (C) 2008 Elsevier B.V. All rights reserved.

}, keywords = {Crystal morphology, Growth from solution, Inorganic compound, Polycrystalline deposition, Semiconducting materials, X-ray diffraction}, issn = {0022-0248}, doi = {10.1016/j.jcrysgro.2008.09.188}, author = {Hankare, P. P. and Patil, A. A. and Chate, P. A. and Garadkar, K. M. and Sathe, D. J. and Manikshete, A. H. and Mulla, Imtiaz S.} } @article { ISI:000257538200034, title = {Co-precipitation technique to prepare BiNbO4 powders}, journal = {Ceramics International}, volume = {34}, number = {6}, year = {2008}, month = {AUG}, pages = {1565-1567}, publisher = {ELSEVIER SCI LTD}, type = {Article}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, OXON, ENGLAND}, abstract = {

A simple co-precipitation technique was successfully used for the preparation of pure ultrafine single phase BiNbO4. A standard ammonium hydroxide solution was used to precipitate Bi3+ and Ta5+ cations as hydroxides simultaneously under basic conditions. For comparison, BN powders were also prepared by the traditional solid-state method. It is observed that the co-precipitation technique produces BiNbO4 on heating at 600 degrees C, whereas complete phase formation occurs only at 800 degrees C in the solid-state method. The phase contents and lattice parameters were Studied by powder X-ray diffraction (XRD). (C) 2007 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

}, keywords = {BiNbO4, Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0272-8842}, doi = {10.1016/j.ceramint.2007.03.022}, author = {Radha, R. and Gupta, U. N. and Samuel, V. and Muthurajan, H. and Kumar, H. H. and Ravi, V.} } @article { ISI:000252408000041, title = {Co-precipitation technique to prepare BiTaO4 powders}, journal = {Materials Letters}, volume = {62}, number = {3}, year = {2008}, month = {FEB}, pages = {501-503}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A simple co-precipitation technique has been successfully used for the preparation of pure ultrafine single phase BiTaO4. A standard ammonium hydroxide solution was used to precipitate Bi3+ and Ta5+ cations as hydroxides simultaneously under basic conditions. This precursor, on heating at 600 degrees C, produced product phase. This is the lowest temperature for the formation of BiTaO4 phase so far reported in the literature. For comparison BiTaO4 powders were also prepared by the traditional solid state method. The phase contents and lattice parameters were studied by the powder X-ray diffraction (XRD). (c) 2007 Elsevier B.V. All rights reserved.

}, keywords = {BiTaO4, Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.05.074}, author = {Muthurajan, H. and Gupta, U. N. and Rituraj, B. and Rao, N. Koteswara and Pradhan, Sivaram and Radha, R. and Ravi, V.} } @article { ISI:000257367100016, title = {Low temperature synthesis and characterization of BiNbO4 powders}, journal = {Materials Characterization}, volume = {59}, number = {8}, year = {2008}, month = {AUG}, pages = {1083-1087}, publisher = {ELSEVIER SCIENCE INC}, address = {360 PARK AVE SOUTH, NEW YORK, NY 10010-1710 USA}, abstract = {

BiNbO4 powders, a potential microwave dielectric ceramic were prepared by both coprecipitation and solid state techniques. In the former method, an aqueous ammonium hydroxide was used to precipitate Bi3+ and Ta5+ cations as hydroxides simultaneously under basic conditions. It is observed that the co-precipitation produces BiNbO4 phase on heating at 600 degrees C, whereas complete phase formation occurs only at 800 degrees C in the case of solid state method. The phase contents and lattice parameters were studied by powder X-ray diffraction. The sequence of the reaction and phase evolution of BiNbO4 were also studied by the X-ray diffraction. The samples were characterized by the differential-thermal/thermo-gravimetric analyses and scanning electron microscopy techniques. (C) 2007 Elsevier Inc. All rights reserved.

}, keywords = {BiNbO4, Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {1044-5803}, doi = {10.1016/j.matchar.2007.08.026}, author = {Radha, R. and Muthurajan, H. and Rao, N. Koteswara and Pradhan, Sivaram and Gupta, U. N. and Jha, Ratnesh Kumar and Mirji, S. A. and Ravi, V.} } @article { ISI:000253106100026, title = {Low temperature synthesis of SrNb2O6 and SrTa2O6 using hydroxide precursor}, journal = {Materials Letters}, volume = {62}, number = {6-7}, year = {2008}, month = {MAR}, pages = {892-894}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

SrNb2O6 (SN) or SrTA(2)O(6) (ST) compounds were prepared at low temperatures for the first time from hydroxide precursors. A simple procedure of mixing commercially purchased strontium hydroxide and niobium (or tantalum) hydroxide thoroughly together and heating at a low temperature (\<400 degrees C) produced SrNb2O6 (SN) or SrTa2O6 (ST) powders. This is the lowest temperature so far reported for the formation of these phases. These materials are potential candidates for ferroelectric and electro-optic applications. The reaction sequence and evolution of the phase formation were investigated by X-ray diffraction (XRD) studies. The average particle size and morphology of these powders were studied by scanning electron microscopy (SEM). (C) 2007 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Electron microscopy, electronic materials, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.07.006}, author = {Muthurajan, H. and Kumar, H. H. and Koteswara Rao, N. and Pradhan, Sivaram and Jha, Ratnesh Kumar and Ravi, V.} } @article { ISI:000257365900027, title = {Novel hydroxide precursors for low temperature synthesis of selected ternary oxides}, journal = {Materials Research Bulletin}, volume = {43}, number = {7}, year = {2008}, month = {JUL}, pages = {1842-1849}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A novel method of using hydroxide precursors to reduce the synthesis temperature for few selected ternary oxides has been presented here. This technique is very useful and advantageous when the ternary oxides contain an alkaline earth element. The selected compositions for this method are BaCeO3 (BC), BaBiO3 (BB), La0.7Sr0.3CoO3 (LSCO) and BaBi2Nb2O9 (BBN). Commercially purchased strontium (or barium) hydroxide and freshly prepared lanthanum, cobalt, bismuth and niobium hydroxides were mixed thoroughly in stoichiometric ratio and heated at different temperatures ranging from 100 to 700 degrees C for 10 h for corresponding compositions. The sequence of the reaction and evolution of the product phase were studied by the X-ray diffraction (XRD) studies. The phase purity and lattice parameters were also determined by XRD investigations. All the product phases in each case were formed at relatively low temperature than when they were prepared by co-precipitation or solid state method. The morphology and average particle size of these powders were investigated by scanning electron microscopy (SEM). (C) 2007 Elsevier Ltd. All rights reserved.

}, keywords = {Ceramics, Chemical synthesis, Electron microscopy, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2007.07.006}, author = {Muthurajan, H. and Rao, N. Koteswara and Gupta, U. N. and Pradhan, Sivaram and Jha, Ratnesh Kumar and Kumar, H. H. and Mirji, S. A. and Ravi, V.} } @article { ISI:000257815100074, title = {Preparation and electrochemical characterization of lithium cobalt oxide nanoparticles by modified sol-gel method}, journal = {Materials Research Bulletin}, volume = {43}, number = {8-9}, year = {2008}, month = {AUG}, pages = {2497-2503}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Uniformly distributed nanoparticles of LiCoO2 have been synthesized through the simple sol-gel method in presence of neutral surfactant (Tween-80). The powders were characterized by X-ray diffractometry, transmission electron microscopy and electrochemical method including charge-discharge cycling performance. The powder calcined at a temperature of 900 degrees C for 5 h shows pure phase layered LiCoO2. The results show that the particle size is reduced in presence of surfactant as compared to normal sol-gel method. Also, the sample prepared in presence of surfactant and calcined at 900 degrees C for 5 h shows the highest initial discharge capacity (106 mAh g(-1)) with good cycling stability as compared to the sample prepared without surfactant which shows the specific discharge capacity of 50 mAh g(-1). (C) 2007 Elsevier Ltd. All rights reserved.

}, keywords = {Electrochemical properties, intercalation reactions, Layered compounds, Sol-gel chemistry, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2007.08.033}, author = {Khomane, Ramdas B. and Agrawal, Amit C. and Kulkarni, B. D. and Gopukumar, S. and Sivashanmugam, A.} } @article { ISI:000252408000048, title = {Synthesis of LSMO at low temperature by novel hydroxide precursor technique}, journal = {Materials Letters}, volume = {62}, number = {3}, year = {2008}, month = {FEB}, pages = {527-529}, publisher = {ELSEVIER SCIENCE BV}, type = {Article}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

A novel technique of mixing individual hydroxide is employed to prepare La0.65Sr0.35MnO3 (LSMO) at low temperature. Freshly prepared lanthanum and manganese hydroxides are mixed thoroughly with strontium hydroxide in stoichiometric ratio and heated at different temperatures ranging from 100 to 500 degrees C for 6 h. At 500 degrees C, formation of La0.65Sr0.35MnO3 was confirmed by the X-ray diffraction studies (XRD). This is the lowest temperature so far reported in the literature. The particle size and morphology were investigated by scanning electron microscopy (SEM). (c) 2007 Elsevier B.V. All rights reserved.

}, keywords = {Ceramics, Electron microscopy, La0.65Sr0.35MnO3, Oxides, Precipitation, X-ray diffraction}, issn = {0167-577X}, doi = {10.1016/j.matlet.2007.05.077}, author = {Gupta, U. N. and Muthurajan, H. and Kumar, H. H. and Rao, N. Koteswara and Gokhale, Suresh P. and Ravi, V.} } @article { ISI:000262886200019, title = {Epitaxially grown zinc-blende structured Mn doped ZnO nanoshell on ZnS nanoparticles}, journal = {Materials Research Bulletin}, volume = {44}, number = {2}, year = {2009}, month = {FEB}, pages = {339-344}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Zinc oxide in the bulk as well as in the nanocrystalline form is thermodynamically stable in the wurtzite structure. However, zinc oxide in the zinc-blende structure is more useful than that in the wurtzite structure due to its superior electronic properties as well as possibility of efficient doping. Therefore, zinc oxide shell is grown epitaxially on zinc sulphide core nanoparticles having zinc-blende structure. It is shown that doping of manganese could be achieved in zinc oxide nanoshell with zinc-blende structure. (C) 2008 Elsevier Ltd. All rights reserved.

}, keywords = {Chemical synthesis, Luminescence, Nanostructures, Semiconductors, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2008.05.015}, author = {Limaye, Mukta V. and Singh, Shashi B. and Date, Sadgopal K. and Gholap, Ramkrishna S. and Kulkarni, Sulabha K.} } @article { ISI:000268022700058, title = {Magnetic and dielectric properties of nanophase manganese-substituted lithium ferrite}, journal = {Journal of Magnetism and Magnetic Materials}, volume = {321}, number = {19}, year = {2009}, month = {OCT}, pages = {3270-3273}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Nanocrystalline manganese-substituted lithium ferrites viz. Li0.5Fe2.5-xMnxO4 (2.5 \<= x \>= 0) were prepared by sol-gel autocombustion method. X-ray diffraction analysis confirmed that as the concentration of manganese increases the cubic phase changes to the tetragonal phase. The variation of saturation magnetization was studied as a function of manganese content. All the compositions indicate that they are ferrimagnetic in nature. The dielectric constant, dielectric loss tangent and ac conductivity of all samples were measured at room temperature as a function of frequency. These parameters decrease with increase in frequency for all of the samples. The substitution of manganese plays an important role in changing the structural and magnetic properties of these ferrites. The compositional variation of dielectric constant and d.c. resistivity shows an inverse trend of variation with each other. (C) 2009 Elsevier B.V. All rights reserved.

}, keywords = {dielectric constant, Ferrite, Magnetization, X-ray diffraction}, issn = {0304-8853}, doi = {10.1016/j.jmmm.2009.05.074}, author = {Hankare, P. P. and Patil, R. P. and Sankpal, U. B. and Jadhav, S. D. and Mulla, Imtiaz S. and Jadhav, K. M. and Chougule, B. K.} } @article { ISI:000264969200041, title = {Microwave-assisted synthesis and humidity sensing of nanostructured alpha-Fe2O3}, journal = {Materials Research Bulletin}, volume = {44}, number = {5}, year = {2009}, month = {MAY}, pages = {1179-1182}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Nanocrystalline alpha-Fe2O3 has been prepared on a large-scale by a facile microwave-assisted hydrothermal route from a solution of Fe(NO3)(3)center dot 9H(2)O and pentaerythritol. A systematic study of the morphology, crystallinity and oxidation state of Fe using different characterization techniques. Such as transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy was performed It reveals. that nanostructured alpha-Fe2O3 comprises bundles of nanorods with a rhombohedral crystalline Structure. The individual nanorod has 8-10 nm diameter and similar to 50 nm length. The as-prepared nanostructured alpha-Fe2O3 (sensor) gives selective response towards humidity. The sensor shows high sensitivity, fast linear response to change in the humidity with almost 100\% reproducibility. The sensor works at room temperature and rejuvenates without heat treatment. The as-prepared nanostructured alpha-Fe2O3 appears to be a promising humidity sensing material with the potential for commercialization. (C) 2008 Elsevier Ltd. All rights reserved.

}, keywords = {Chemical synthesis, Electrical properties, Nanostructures, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2008.09.044}, author = {Deshmukh, Rupali G. and Badadhe, Satish S. and Mulla, Imtiaz S.} } @article { ISI:000265933700042, title = {Origin of high room temperature ferromagnetic moment of nanocrystalline multiferroic BiFeO3}, journal = {Applied Physics Letters}, volume = {94}, number = {18}, year = {2009}, month = {MAY}, pages = {182507}, publisher = {AMER INST PHYSICS}, address = {CIRCULATION \& FULFILLMENT DIV, 2 HUNTINGTON QUADRANGLE, STE 1 N O 1, MELVILLE, NY 11747-4501 USA}, abstract = {

Single phase nanocrystalline BiFeO3 of average crystallite size similar to 25 nm with very high magnetization at room temperature is synthesized by an autocombustion method. Magnetic measurements above room temperature show deviation between field cooled and zero field cooled magnetization below 645 K, the Neel temperature (T-N) of the bulk material, indicating intrinsic nature of ferromagnetism. However, observation of a broad magnetic transition above T-N of BiFeO3 and extended up to 800 K suggests the presence of Fe3O4 as a possible magnetic impurity phase. Evidence for the presence of Fe3O4 is obtained from detailed analysis of the powder x-ray diffraction pattern.

}, keywords = {bismuth compounds, Combustion synthesis, crystallites, ferromagnetic materials, high-temperature effects, magnetic impurities, Magnetic moments, Magnetisation, Multiferroics, Nanostructured materials, Neel temperature, X-ray diffraction}, issn = {0003-6951}, doi = {10.1063/1.3132586}, author = {Vijayanand, S. and Potdar, H. S. and Joy, Pattayil Alias} } @article { ISI:000267546200006, title = {Structural characterization of azoic dye hosted layered double hydroxides}, journal = {Zeitschrift fur Kristallographie}, volume = {224}, number = {5-6}, year = {2009}, month = {JAN}, pages = {282-286}, publisher = {OLDENBOURG VERLAG}, address = {LEKTORAT MINT, POSTFACH 80 13 60, D-81613 MUNICH, GERMANY}, abstract = {

The removal of methyl orange (MO) from an aqueous solution was performed using layered double hydroxides (LDHs) in a move to develop cleaning processes of effluents contaminated with dye molecules. The intercalation of the guest anionic MO species into host M(II)/Al(III) LDHs differing by the nature of the divalent cations (M(II) = Mg, Ni or Zn) was achieved by anionic exchange of the initially NO(3)(-) present in the interlayer space and led to MO/LDH intercalation compounds. The exchange process was followed by XRD and UV-visible absorption spectroscopy at different stages. Almost all MO in solution is uptaken by the Mg-containing LDH in the concentration range corresponding to its anionic exchange capacity (AEC). A lower exchange is reached with the Ni- and Zn-containing LDHs, for which the diffusion of MO is limited due to a larger crystallite size. MO-Zn/Al LDH intercalation compounds exhibit the highest crystallinity and display a remarkable stacking of the layers at maximal MO exchange. This behaviour can be assigned to the higher intrinsic charge density of the host layers in agreement with its lower M(II)/Al(III) molar ratio (Zn(II)/Al(III) approximate to 1.5 whereas Mg(II)/Al(III) and Ni(II)/Al(III) = 2). The maximum amount of MO retained by the different LDHs is higher for Mg-containing LDH, than for Ni- and Zn-containing LDH, reaching respectively 1.15, 0.84 and 0.77 g/g.

}, keywords = {Anionic exchange, Depollution, layered double hydroxides, Methyl orange, X-ray diffraction}, issn = {0044-2968}, doi = {10.1524/zkri.2009.1150}, author = {Mandal, Sujata and Lerner, Dan A. and Marcotte, Nathalie and Tichit, Didier} } @article { ISI:000271542900148, title = {On the structural, magnetic and electrical properties of sol-gel derived nanosized cobalt ferrite}, journal = {Journal of Alloys and Compounds}, volume = {485}, number = {1-2}, year = {2009}, month = {OCT}, pages = {711-717}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Nanoparticles of cobalt ferrite were synthesized by sol gel method. These particles were structurally characterized by using X-Ray Diffraction and Transmission Electron Microscopy, High Resolution Transmission Electron Microscopy, Energy Dispersive Spectrum and Inductively Coupled Plasma Analysis and the results confirmed the formation of spherically shaped nanoparticles of cobalt ferrite having a size lying in the range of 13-14 nm. The as prepared sample was sintered at 800 degrees C and the structural, magnetic and dielectric properties were measured. The dielectric properties were studied and analyzed as a function of temperature and frequency. The ac and dc conductivity studies were carried out to delve into the conduction mechanism. The existing models based on quantum mechanical tunneling were effectively employed to explain the frequency dependent conductivity. (C) 2009 Elsevier B.V. All rights reserved.

}, keywords = {Electronic Transport, Magnetic measurements, Magnetically ordered materials, Nanostructures, Scanning and transmission electron microscopy, Sol-gel synthesis, X-ray diffraction}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2009.06.033}, author = {Gopalan, E. Veena and Joy, Pattayil Alias and Al-Omari, I. A. and Kumar, D. Sakthi and Yoshida, Yasuhiko and Anantharaman, Maliemadom R.} } @article { ISI:000271542900165, title = {Synthesis and characterization of CoCrxFe2-xO4 nanoparticles}, journal = {Journal of Alloys and Compounds}, volume = {485}, number = {1-2}, year = {2009}, month = {OCT}, pages = {798-801}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Spinel-phase nanocrystalline CoCrxFe2-xO4 powders (0.0 \<= x \<= 2.0) were synthesized by citrate-gel precursor method. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). transmission electron microscopy (TEM) and infra-red spectroscopy (FT-IR). The XRD and selected-area electron diffraction (SAED) patterns indicated that the synthesized nanoparticles have single-phase spinet structure without the presence of any other impurities. The changes in electrical and magnetic properties of different stiochiometric compositions have also been investigated. It is seen that with increase in chromium contents, the measured magnetic hysteresis loops become narrow with decreasing trend in saturation magnetization. Electrical resistivity indicated that all the compounds are semiconducting nature. (C) 2009 Elsevier B.V. All rights reserved.

}, keywords = {Magnetic measurements, Sintering, transmission electron microscopy, X-ray diffraction}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2009.06.087}, author = {Hankare, P. P. and Sankpal, U. B. and Patil, R. P. and Mulla, Imtiaz S. and Lokhande, P. D. and Gajbhiye, N. S.} } @article { ISI:000265911700183, title = {Synthesis, characterization and effect of sintering temperature on magnetic properties of MgNi ferrite prepared by co-precipitation method}, journal = {Journal of Alloys and Compounds}, volume = {475}, number = {1-2}, year = {2009}, month = {MAY}, pages = {926-929}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Mixed MgNi ferrites with composition Mg(0.5)Ni(0.5)Fe(2)O(4) where the mole fraction for Ni (x = 0, 0.25, 0.75, 0.5 and 1) were prepared by following co-precipitation method at temperature 110 degrees C and maintaining a pH of solution equal to 9.5 enable to achieve large particle surface area. The resultant materials obtained in powder form were sintered at different temperatures. Thermogravimetry (TGA), X-ray diffraction (XRD) and scanning electron microscopy, technique were applied to obtain structural parameters. The XRD patterns reveal the presence of(311) peak as the most intense one. The intensity of XRD peak increases with increase in sintering temperature. The saturation magnetization values showed increasing trend with increase in sintering temperature from 2.37 to 29.76 emu/g. These results along with the analysis of SEM micrographs are interpreted in terms of increase in particle grain size with increase in sintering temperature. (C) 2008 Elsevier B.V. All rights reserved.

}, keywords = {Chemical synthesis, Ferrites, FT-IR, scanning electron microscopy, X-ray diffraction}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2008.08.082}, author = {Hankare, P. P. and Jadhav, S. D. and Sankpal, U. B. and Chavan, Santosh S. and Waghmare, K. J. and Chougule, B. K.} } @article { ISI:000278305600001, title = {Magnetic, dielectric and complex impedance spectroscopic studies of nanocrystalline Cr substituted Li-ferrite}, journal = {Journal of Magnetism and Magnetic Materials}, volume = {322}, number = {18}, year = {2010}, month = {SEP}, pages = {2629-2633}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Nanocrystalline Li0.5Fe2.5-xCrxO4 (2.5 \<= x \>= 0) ferrites were prepared by a sol-gel autocombustion route. X-ray diffraction was employed to confirm the cubic spinel phase formation of the ferrites. The lattice parameter decreases with increase in Cr content. The saturation magnetization, coercivity and remanance were studied as a function of Cr content. The dielectric constant and dielectric loss were measured as a function of frequency in the frequency range 20 Hz-1 MHz. Frequency dependence of dielectric constant shows dielectric dispersion due to the Maxwell-Wagner type of interfacial polarization. In order to understand the conduction mechanism, complex impedance measurements were carried out. The substitution of chromium plays an important role in changing the dielectric and magnetic properties of lithium ferrites. (C) 2010 Published by Elsevier B.V.

}, keywords = {Complex impedance, dielectric response, Ferrites, Magnetic hysteresis, Sol-gel synthesis, X-ray diffraction}, issn = {0304-8853}, doi = {10.1016/j.jmmm.2010.03.005}, author = {Hankare, P. P. and Patil, R. P. and Sankpal, U. B. and Garadkar, K. M. and Sasikala, R. and Tripathi, A. K. and Mulla, Imtiaz S.} } @article { ISI:000288092200005, title = {Preparation and characterization of bioceramic nanocomposites based on hydroxyapatite (HA) and carboxymethyl cellulose (CMC)}, journal = {Macromolecular Research}, volume = {18}, number = {12}, year = {2010}, month = {DEC}, pages = {1160-1167}, publisher = {SPRINGER}, address = {233 SPRING ST, NEW YORK, NY 10013 USA}, abstract = {

We report the synthesis of biomimetic nanocomposites based on carboxymethyl cellulose (CMC) and hydroxyapatite (HA) nanoparticles via a co-precipitation method. Physico-chemical characterization was performed before and after calcination by Fourier transform infrared (FTIR) spectroscopy, solid state (31)P nuclear magnetic resonance (NMR) spectroscopy, and thermogravimetric analysis (TGA). The formation of nanocomposites was observed by wide angle X-ray diffraction (WAXD), scanning electron microscopy (SEM) with energy dispersive X-ray analysis (EDX), and transmission electron microscopy (TEM). The spectral and crystallographic data indicated the formation of hydroxyapatite in the presence of CMC. They were observed as aggregates of HA nanoparticles and CMC, whose sizes were approximately similar to 260 +/- 40 nm. The crystallite size of the hydroxyapatite particles decreased (with 2 wt\% 18 +/- 3 nm) with increasing CMC content. The morphological aspects of the calcined samples revealed the sintering ability of HA nanoparticles. Nanocomposites of hydroxyapatite nanoparticles that mimic the process of nucleation and growth in nature can be prepared using biomacromolecules such as CMC.

}, keywords = {biopolymer, cellulose, hydroxyapatite, Nanoparticles, Particle size, X-ray diffraction}, issn = {1598-5032}, doi = {10.1007/s13233-010-1208-3}, author = {Kumar, Annamalai Pratheep and Mohaideen, Kamal Khaja and Alariqi, Sameh A. S. and Singh, Raj Pal} } @article { ISI:000279139400020, title = {Preparation and characterization of CuInSe2 thin films by chemical bath deposition technique}, journal = {Journal of Alloys and Compounds}, volume = {500}, number = {1}, year = {2010}, month = {JUN}, pages = {78-81}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Copper indium diselenide (CIS) thin films have been deposited using a precursor solution containing copper sulphate, indium trichoride, hydrazine hydrate and sodium selenosulphate in an aqueous alkaline medium at room temperature. The as grown brown colored films were found to be well adherent to glass substrates. The films were characterized by X-ray diffraction, scanning electron microscopy, atomic absorption spectroscopy, optical absorption, electrical resistivity, and thermo electric measurement techniques. The analysis of optical absorption data shows band-gap energy (E-g) to be 1.1 eV. The electrical resistivity of the thin film was found to be of the order of 10(2) (Omega cm). Thermoelectric power measurement shows n-type conduction. (C) 2010 Published by Elsevier B.V.

}, keywords = {CuInSe2, Optical properties, Thin films, X-ray diffraction}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2010.03.215}, author = {Hankare, P. P. and Rathod, K. C. and Chate, P. A. and Jadhav, A. V. and Mulla, Imtiaz S.} } @article { ISI:000281347500022, title = {Surface texture and specific adsorption sites of sol-gel synthesized anatase TiO2 nanoparticles}, journal = {Materials Research Bulletin}, volume = {45}, number = {10}, year = {2010}, month = {OCT}, pages = {1470-1475}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

The surface properties of sot-gel synthesized anatase titania (TiO2) nanoparticles are probed by sorptiometry, infrared absorption spectroscopy, UV-vis diffuse reflectance spectroscopy and high resolution transmission electron microscopy. The results reveal strong correlations of the surface area, porosity, pyridine adsorption capacity and strength, and catalytic methylbutynol decomposition activity. (C) 2010 Elsevier Ltd. All rights reserved.

}, keywords = {Catalytic properties, Nanostructures, Oxides, Sol-gel chemistry, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2010.06.026}, author = {Zaki, Mohamed I. and Mekhemer, Gamal A. H. and Fouad, Nasr E. and Jagadale, Tushar C. and Ogale, Satishchandra B.} } @article { ISI:000278744500055, title = {Synthesis and characterization of nanocrystalline zinc substituted nickel ferrites}, journal = {Journal of Alloys and Compounds}, volume = {496}, number = {1-2}, year = {2010}, month = {APR}, pages = {256-260}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Nanocrystalline zinc substituted nickel ferrites, Ni(1-x)Zn(x)Fe(2)O(4) (0.0 \<= x \<= 1.0) have been prepared by citrate gel auto-combustion method. The effect of zinc ion content on structural, electrical transport and magnetic properties has been studied. The X-ray diffraction (XRD) pattern revealed that, all the compositions possess single-phase spinel structure. The nano-sized grain structure formation was confirmed by transmission electron microscopy (TEM). The dc electrical resistivity shows the samples are semiconducting in nature. The magnetic measurements showed that the composition Ni(0.6)Zn(0.4)Fe(2)O(4) has maximum saturation magnetization (M(s)) while high coersivity (Hc) for ZnFe(2)O(4). Thermoelectric power measurement study showed that the compounds, with x \<= 0.4 are p-type and for x \> 0.4 behaves n-type conduction mechanism. (C) 2010 Published by Elsevier B.V.

}, keywords = {Electron microscopy, Magnetic, Sintering, X-ray diffraction}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2010.01.009}, author = {Hankare, P. P. and Sankpal, U. B. and Patil, R. P. and Mulla, Imtiaz S. and Sasikala, R. and Tripathi, A. K. and Garadkar, K. M.} } @article { ISI:000274839100053, title = {Synthesis and characterization of nickel selenide thin films deposited by chemical method}, journal = {Journal of Alloys and Compounds}, volume = {490}, number = {1-2}, year = {2010}, month = {FEB}, pages = {228-231}, publisher = {ELSEVIER SCIENCE SA}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Nickel selenide thin films have been deposited using chemical bath method on non-conducting glass substrates in a tartarate bath containing nickel sulphate octahydrate, hydrazine hydrate, sodium seleno-sulphate in an aqueous alkaline medium. The grown films were uniform, well adherent and black in color. The films were characterized using X-ray diffraction, scanning electron microscopy, optical absorption and electrical measurements. The nickel selenide thin film revealed polycrystalline nature with hexagonal system. The direct optical band gap of the film was found to be 1.61 eV. Electrical resistivity of film was observed in the order of 10(3) (Omega cm) with p-type conduction mechanism. (C) 2009 Elsevier B.V. All rights reserved.

}, keywords = {Crystal growth, Semiconductors, Thin films, X-ray diffraction}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2009.09.132}, author = {Hankare, P. P. and Jadhav, B. V. and Garadkar, K. M. and Chate, P. A. and Mulla, Imtiaz S. and Delekar, S. D.} } @article { ISI:000289763700002, title = {Novel solar light driven photocatalyst, zinc indium vanadate for photodegradation of aqueous phenol}, journal = {Materials Research Bulletin}, volume = {46}, number = {5}, year = {2011}, month = {MAY}, pages = {635-638}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

In the present investigation, we have demonstrated the synthesis of novel photocatalyst, zinc indium vanadate (ZIV) by solid solid state route using respective oxides of zinc, indium and vanadium. This novel photocatalyst was characterized using XRD, FESEM, UV-DRS and FTIR in order to investigate its structural, morphological and optical properties. XRD clearly shows the formation of phase pure ZIV of triclinic crystal structure with good crystallinity. FESEM micrographs showed the clustered morphology having particle size between 0.5 and 1 mu m. Since, optical study showed the band gap around 2.8 eV, i.e. in visible region, we have performed the photocatalytic activity of phenol degradation under visible light irradiation. The photodecomposition of phenol by ZIV is studied for the first time and an excellent photocatalytic activity was obtained using this novel photocatalyst. Considering the band gap of zinc indium vanadate in visible region, it will also be the potential candidate for water splitting. (C) 2011 Elsevier Ltd. All rights reserved.

}, keywords = {Catalytic properties, Chemical synthesis, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2011.02.005}, author = {Mahapure, Sonali A. and Rane, Vilas H. and Ambekar, Jalindar D. and Nikam, Latesh K. and Marimuthu, R. and Kulkarni, Milind V. and Kale, Bharat B.} } @article { ISI:000298731200036, title = {Fluorinated metal-organic frameworks: advantageous for higher H-2 and CO2 adsorption or not?}, journal = {Chemistry-A European Journal}, volume = {18}, number = {2}, year = {2012}, month = {JAN}, pages = {688-694}, publisher = {WILEY-V C H VERLAG GMBH}, address = {BOSCHSTRASSE 12, D-69469 WEINHEIM, GERMANY}, abstract = {

The synthesis, structure, and gas adsorption properties of three new metalorganic frameworks (MOFs) designed from isonicotinic acid (INA) and its fluorinated analogue 3-fluoroisonicotinic acid (FINA) along with CoII as the metal center have been reported. Co-INA-1 ([Co3(INA)4(O)(C2H5OH)3][NO3].C2H5OH.3?H2O; INA=isonicotinic acid) and Co-INA-2 ([Co(INA)2].DMF) are structural isomers as are Co-FINA-1 ([Co3(FINA)4(O)(C2H5OH)2].H2O; FINA=3-fluoroisonicotinic acid) and Co-FINA-2 ([Co(FINA)2].H2O), but the most important thing to note here is that Co-INA-1 and Co-FINA-1 are isostructural as are Co-INA-2 and Co-FINA-2. The effect of partial introduction of fluorine atoms into the framework on the gas uptake properties of MOFs having similar structures has been analyzed experimentally and computationally in isostructural MOFs.

}, keywords = {cobalt, fluorine, Hydrogen storage, metal-organic frameworks, microporous materials, X-ray diffraction}, issn = {0947-6539}, doi = {10.1002/chem.201102295}, author = {Pachfule, Pradip and Chen, Yifei and Jiang, Jianwen and Banerjee, Rahul} } @article { ISI:000312004800088, title = {Bulk and surface structure characterization of nanoscopic silver doped lanthanum chromites}, journal = {Applied Surface Science}, volume = {264}, year = {2013}, month = {JAN}, pages = {574-580}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Crystalline state of lanthanum chromites with silver as a dopant has been studied by X-ray diffraction and transmission electron microscopy reveals microscopic properties of grain boundaries. X-ray photoelectron spectroscopy has been used to analyze surface states with atomic ratio of La, Cr, O and Ag as a dopant. LaCrO3 shows mixed valence states of chromium while the silver doped samples exhibit differences in chromium concentration with the oxidation of Cr3+ to Cr6+ in presence of chromium nitrate as a precursor salt. Trivalent stable state of chromium is observed for samples synthesized by chromic acetate as a precursor salt. (C) 2012 Elsevier B.V. All rights reserved.

}, keywords = {Energy dispersive analysis of X-rays, Microwave combustion synthesis, Perovskite nanostructures, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy}, issn = {0169-4332}, doi = {10.1016/j.apsusc.2012.10.067}, author = {Desai, P. A. and Joshi, P. N. and Patil, K. R. and Athawale, Anjali A.} } @article { ISI:000319417100005, title = {Design, synthesis, structural characterization by IR, 1H, 13C, 15N, 2D-NMR, X-ray diffraction and evaluation of a new class of phenylaminoacetic acid benzylidene hydrazines as pfENR inhibitors}, journal = {Chemical Biology \& Drug Design}, volume = {81}, number = {6}, year = {2013}, month = {JUN}, pages = {715-729}, publisher = {WILEY-BLACKWELL}, address = {111 RIVER ST, HOBOKEN 07030-5774, NJ USA}, abstract = {

Recent studies have revealed that plasmodial enoyl-ACP reductase (pfENR, FabI), one of the crucial enzymes in the plasmodial type II fatty acid synthesis II (FAS II) pathway, is a promising target for liver stage malaria infections. Hence, pfENR inhibitors have the potential to be used as causal malarial prophylactic agents. In this study, we report the design, synthesis, structural characterization and evaluation of a new class of pfENR inhibitors. The search for inhibitors began with a virtual screen of the iResearch database by molecular docking. Hits obtained from the virtual screen were ranked according to their Glide score. One hit was selected as a lead and modified to improve its binding to pfENR; from this, a series of phenylamino acetic acid benzylidene hydrazides were designed and synthesized. These molecules were thoroughly characterized by IR, 1H, 13C, 15N, 2D-NMR (COSY, NOESY, 1H-13C, 1H-15N HSQC and HMBC), and X-ray diffraction. NMR studies revealed the existence of conformational/configurational isomers around the amide and imine functionalities. The major species in DMSO solution is the E, E form, which is in dynamic equilibrium with the Z, E isomer. In the solid state, the molecule has a completely extended conformation and forms helical structures that are stabilized by strong hydrogen bond interactions, forming a helical structure stabilized by N-H...O interactions, a feature unique to this class of compounds. Furthermore, detailed investigation of the NMR spectra indicated the presence of a minor impurity in most compounds. The structure of this impurity was deduced as an imidazoline-4-one derivative based on 1H-13C and 1H-15H HMBC spectra and was confirmed from the NOESY spectra. The molecules were screened for in vitro activity against recombinant pfENR enzyme by a spectrophotometric assay. Four molecules, viz. 17, 7, 10, and 12 were found to be active at 7, 8, 10, and 12m concentration, respectively, showing promising pfENR inhibitory potential. A classification model was derived based on a binary QSAR approach termed recursive partitioning (RP) to highlight structural characteristics that could be tuned to improve activity.

}, keywords = {ADMET, docking, enoyl-ACP reductase, FabI, hydrogen bonding, NMR, phenylaminoacetic acid benzylidene hydrazine, Plasmodium falciparum, Plasmodium falciparum enoyl-ACP reductase, QSAR, recursive partitioning, X-ray diffraction}, issn = {1747-0277}, doi = {10.1111/cbdd.12118}, author = {Samal, Ramanuj P. and Khedkar, Vijay M. and Pissurlenkar, Raghuvir R. S. and Bwalya, Angela Gono and Tasdemir, Deniz and Joshi, Ramesh A. and Rajamohanan, P. R. and Puranik, Vedavati G. and Coutinho, Evans C.} } @article { ISI:000324077700076, title = {Fungus mediated synthesis of biomedically important cerium oxide nanoparticles}, journal = {Materials Research Bulletin}, volume = {48}, number = {10}, year = {2013}, month = {OCT}, pages = {4134-4138}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Nanomaterials can be synthesized by chemical, physical and the more recently discovered biological routes. The biological routes are advantageous over the chemical and physical ones as unlike these, the biological synthesis protocols occur at ambient conditions, are cheap, non-toxic and eco-friendly. Although purely biological and bioinspired methods for the synthesis of nanomaterials are environmentally benign and energy conserving processes, their true potential has not been explored yet and attempts are being made to extend the formation of technologically important nanoparticles using microorganisms like fungi. Though there have been reports on the biosynthesis of oxide nanoparticles by our group in the past, no attempts have been made to employ fungi for the synthesis of nanoparticles of rare earth metals or lanthanides. Here we report for the first time, the bin-inspired synthesis of biomedically important cerium oxide (CeO2) nanoparticles using the thermophilic fungus Humicola sp. The fungus Humicola sp. when exposed to aqueous solutions of oxide precursor cerium (III) nitrate hexahydrate (CeN3O9 center dot 6H(2)O) results in the extracellular formation of CeO2 nanoparticles containing Ce (III) and Ce (IV) mixed oxidation states, confirmed by X-ray Photoemission Spectroscopy (XPS). The formed nanoparticles are naturally capped by proteins secreted by the fungus and thus do not agglomerate, are highly stable, water dispersible and are highly fluorescent as well. The biosynthesized nanoparticles were characterized by UV-vis spectroscopy, Photoluminescence spectroscopy (PL), Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD) and X-ray Photoemission Spectroscopy (XPS). (c) 2013 Elsevier Ltd. All rights reserved.

}, keywords = {Electron microscopy, Nanostuctures, Optical properties, Oxides, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2013.06.038}, author = {Khan, Shadab Ali and Ahmad, Absar} } @article { ISI:000324316300042, title = {Identification of molecular crystals capable of undergoing an acyl-transfer reaction based on intermolecular interactions in the crystal lattice}, journal = {Chemistry-A European Journal}, volume = {19}, number = {38}, year = {2013}, month = {SEP}, pages = {12867-12874}, publisher = {WILEY-V C H VERLAG GMBH}, address = {BOSCHSTRASSE 12, D-69469 WEINHEIM, GERMANY}, abstract = {

Investigation of the intermolecular acyl-transfer reactivity in molecular crystals of myo-inositol orthoester derivatives and its correlation with crystal structures enabled us to identify the essential parameters to support efficient acyl-transfer reactions in crystals: 1)the favorable geometry of the nucleophile (OH) and the electrophile (CO) and 2)the molecular assembly, reinforced by CH interactions, which supports a domino-type reaction in crystals. These parameters were used to identify another reactive crystal through a data-mining study of the Cambridge Structural Database. A 2:1 co-crystal of 2,3-naphthalene diol and its di-p-methylbenzoate was selected as a potentially reactive crystal and its reactivity was tested by heating the co-crystals in the presence of solid sodium carbonate. A facile intermolecular p-toluoyl group transfer was observed as predicted. The successful identification of reactive crystals opens up a new method for the detection of molecular crystals capable of exhibiting acyl-transfer reactivity.

}, keywords = {Acylation, domino reactions, intermolecular interactions, solid-state reactions, X-ray diffraction}, issn = {0947-6539}, doi = {10.1002/chem.201301058}, author = {Tamboli, Majid I. and Krishnaswamy, Shobhana and Gonnade, Rajesh G. and Shashidhar, Mysore S.} } @article { ISI:000377826000008, title = {Biogenic green synthesis of monodispersed gum kondagogu (Cochlospermum gossypium) iron nanocomposite material and its application in germination and growth of mung bean (Vigna radiata) as a plant model}, journal = {IET Nanobiotechnology}, volume = {10}, number = {3}, year = {2016}, month = {JUN}, pages = {141-146}, publisher = {INST ENGINEERING TECHNOLOGY-IET}, address = {MICHAEL FARADAY HOUSE SIX HILLS WAY STEVENAGE, HERTFORD SG1 2AY, ENGLAND}, abstract = {

An eco-friendly green and one-pot synthesis of highly monodispersed iron (Fe) nanoparticles (NPs) by using a natural biopolymer, gum kondagogu (GK) as reducing and capping agent is proposed. The NPs synthesised were characterised by ultra-violet-visible spectroscopy, transmission electron microscopy, scanning electron microscopy and X-ray diffraction. As the concentration of gum and time increases, the intensity of NPs formation increased. The NPs were highly monodispersed with uniform circular shapes of 2-6 nm in size. The formed NPs were crystalline in nature which was confirmed by diffraction analysis. The conversion ratio of Fe ionic form to NPs was 21\% which was quantified by inductively coupled plasma mass spectroscopy (ICP-MS). Fe is essential for plant growth and development. A study was conducted to examine the effect of these NPs on the growth of mung bean (Vigna radiata). The radical length and biomass was increased in seeds exposed to Fe NPs than the ions. The uptake of Fe NPs by the sprouts was also quantified by ICP-MS, in which Fe was more in mung bean seeds exposed to NPs. The -amylase activity was increased in the seeds exposed to NPs. The observed increase in the biomass by Fe NPs and seed germination may facilitate its application in the agriculture as an important cost-effective method for plant growth.

}, keywords = {alpha-amylase activity, Biogenic green synthesis, biological techniques, Biomass, Cochlospermum gossypium, diffraction analysis, enzymes, Fe, gum concentration, high-monodispersed iron nanoparticles, inductively coupled plasma mass spectroscopy, ionic-to-nanoparticle iron conversion ratio, iron, monodispersed gum kondagogu, monodispersed gum kondagogu iron nanocomposite material, mung bean germination, mung bean growth, Nanobiotechnology, Nanocomposites, nanoparticle formation, Nanoparticles, natural biopolymer, plant growth, plant model, scanning electron microscopy, size 2 nm to 6 nm, transmission electron microscopy, ultraviolet spectra, ultraviolet-visible spectroscopy, Vigna radiata, visible spectra, X-ray diffraction}, issn = {1751-8741}, doi = {10.1049/iet-nbt.2015.0112}, author = {Raju, Dugyala and Mehta, Urmil J. and Beedu, Sashidhar Rao} } @article { ISI:000374195700036, title = {Photocatalytic degradation of methylene blue on Sn-doped titania nanoparticles synthesized by solution combustion route}, journal = {Materials Research Bulletin}, volume = {76}, year = {2016}, month = {APR}, pages = {264-272}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Series of tin-doped titania nanoparticles with varying tin content in the range 0-20 mol\% have been prepared by solution combustion synthesis route using urea as a fuel. The structure, surface morphology and optical activity of Sn-doped TiO2 nanoparticles were investigated by various analytical techniques such as powder XRD, SEM, TEM, UV-vis and N-2 adsorption study. The crystalline structures of the various phases were studied by rietveld refinement of the XRD data. The photocatalytic performance of Sn-doped titania nanoparticles were tested for degradation of MB under UV and visible light irradiation. The results reveal that the photocatalytic activity increases with increase in tin content which may be due to decrease in crystallite size with increase in surface area. The doping of Sn into TiO2 lattice hinders the recombination of electrons and holes thus enhance the quantum efficiency of photocatalytic reaction. (C) 2015 Elsevier Ltd. All rights reserved.

}, keywords = {Catalytic properties, composites, Nanostructures, X-ray diffraction}, issn = {0025-5408}, doi = {10.1016/j.materresbull.2015.12.041}, author = {Bhange, P. D. and Awate, S. V. and Gholap, Ramkrishna S. and Gokavi, G. S. and Bhange, Deu S.} } @article { ISI:000370900600019, title = {Photoluminescent tetrahedral d(10)-metal Schiff base complexes exhibiting highly ordered mesomorphism}, journal = {Polyhedron}, volume = {105}, year = {2016}, month = {FEB}, pages = {150-158}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

A series of four-coordinate d(10)-metal complexes of the type [ML2] {M = Zn, Cd, Hg; L = 4-nitro-2-((octadecylimino)methyl)phenol}, incorporating a new N-alkylated bidentate [N,O]-donor salicylaldimine Schiff base ligand, has been synthesized and characterized by elemental analyses, FT-IR, UV-Vis, H-1 NMR and FAB-mass spectroscopies. The ligand is non-mesomorphic and devoid of any photoluminescence. The zinc(II) and cadmium(II) complexes displayed highly ordered mesophases reminiscent of soft crystals. The phases have been characterized by polarizing optical microscopy (POM), differential scanning calorimetry (DSC) and powder X-ray diffraction (PXRD) studies. The complex of mercury(II) decomposed prior to melting. An orthogonal symmetry with a {\textquoteleft}herringbone{\textquoteright} array for the zinc complex and a primitive triclinic symmetry (p(1)) for the cadmium complex, respectively, has been proposed. The complexes exhibited fluorescence at room temperature, both in the solution and in the solid state, with emission maxima in the blue region. Density functional theory (DFT) calculations carried out using the GAUSSIAN 09 program at the B3LYP level revealed a distorted tetrahedral geometry around the metal center in all the complexes. Natural bond orbital (NBO) analysis suggested appreciable charge transfer from the ligand to the metal center in the complexes. (C) 2015 Elsevier Ltd. All rights reserved.

}, keywords = {Density functional theory, Luminescence, Mesophase, Schiff base, X-ray diffraction}, issn = {0277-5387}, doi = {10.1016/j.poly.2015.11.053}, author = {Chakraborty, Sutapa and Purkayastha, Debraj Dhar and Das, Gobinda and Bhattacharjee, Chira R. and Mondal, Paritosh and Prasad, S. Krishna and Rao, D. S. Shankar} } @article {45713, title = {Engineering molecular topology: A pseudopeptidic macrocyclic figure-eight motif}, journal = {European Journal of Organic Chemistry}, year = {2017}, month = {FEB }, pages = {1120-1124}, type = {Article}, abstract = {

We herein present a rational-design strategy for the synthesis of molecules with figure-eight topology. The design concept is based on the incorporation of turn units in the back-bone of the macrocycle. The molecular structures and the folding are studied by X-ray crystallography and NMR, FT-IR, and CD spectroscopy.

}, keywords = {Macrocycles, noncovalent interactions, Pi interactions, topology, X-ray diffraction}, issn = {1434-193X}, doi = {10.1002/ejoc.201601365}, author = {Sharma, Sakshi and Thorat, Shridhar H. and Gonnade, Rajesh G. and Jasinski, Jerry P. and Butcher, Ray and Haridas, V.} } @article {44008, title = {Syntheses and single crystal X-ray diffraction studies of hydroxynicotinic acid based complexes involving supramolecular interactions}, journal = {Polyhedron}, volume = {133}, year = {2017}, month = {SEP}, pages = {222-230}, type = {Journal Article}, abstract = {Aqua-bridged coordination polymers of Cu(II) and Cd(II) and a mononuclear complex of Cu(II) were solvothermally synthesized with hydroxy-decorated ligands such as 2-hydroxynicotinic acid (2-OHNAH) and 6-hydroxynicotinic acid (6-OHNAH) in aqueous-nonaqueous mixed media. All these complexes were characterized by elemental analyses (C, H, N), FT-IR, thermogravimetric analysis (TGA), powder XRD and single crystal X-ray crystallography. They are formulated as [Cu(2-OHNA)2] 1, [Cu(6-OHNA)2(μ-H2O)2]n 2 and [Cd(6-OHNA)2(μ-H2O)2]n 3. Complex 1 is mononuclear 0D square planar complex which extends its dimensionality by weak supramolecular interactions such as π{\textendash}π stacking interactions and intermolecular hydrogen bonding. Complexes 2 and 3 are polymeric aqua-bridged 1D infinite chain of Cu(II) and Cd(II), respectively. The central metal ions in these two complexes are in octahedral coordination environment. These two complexes are also assembled by π{\textendash}π stacking interactions, inter- and intramolecular hydrogen bonding interactions. }, keywords = {2-Hydroxynicotinic Acid, 6-Hydroxynicotinic Acid, Coordination polymer, Polymeric Aqua-Bridged, X-ray diffraction}, doi = { 10.1016/j.poly.2017.05.041}, author = {Singh, S.K.}, editor = {Srivastava, K.} } @article {43792, title = {Synthesis, characterization and electrochemical investigations of mixed-ligand copper(II)-organic supramolecular frameworks}, journal = {Journal of Molecular Structure}, volume = {1147}, year = {2017}, month = {NOV}, pages = {549-557}, type = {Article}, abstract = {

Two mixed-ligand copper(II)-organic coordination compounds with 5,5{\textquoteright}-dimethyl-2,2{\textquoteright}-bipyridine (5,5{\textquoteright}-Me(2)bpy) as a primary ligand while aliphatic malonate (Hmal) and aromatic 2-hydroxynicotinate (2-OHNA) as secondary ligands, were synthesized. These complexes are formulated as: [Cu(Hmal)(5,5{\textquoteright}-Me(2)bPY)(H2O)](ClO4) 1 and [Cu-2(2-OHNA)(2)(5,5{\textquoteright}-Me(2)bpy)(2)(NO3)KNO3) 2. These two complexes were structurally characterized by single crystal X-ray diffraction analysis. Characterization was further supported by powder X-ray diffraction analysis, elemental analyses, FT-IR, FAB-MASS and TGA, DSC studies. Cyclic voltammetric and UV-visible spectral studies of these two complexes have also been done. The electrochemical studies of complex 1 in DMSO and DMF have shown that this complex undergoes quasi reversible diffusion-controlled one-electron transfer reaction without any chemical complication while complex 2 in DMSO undergoes quasi-reversible diffusion-controlled one electron transfer reaction, following EC mechanism. The electrochemical behaviour of complex 2 in DMF is complicated probably due to presence of more than one species in solution phase. (C) 2017 Elsevier B.V. All rights reserved.

}, keywords = {2 {\textquoteright}-bipyridine, 3, 5, 5 {\textquoteright}-dimethyl-2, 5-Tricarboxylic acid, Benzene-1, classification, Co-ordination-Compounds, Crystal-structures, cyclic voltammetry, magnetic properties, metal organic framework, Mixed-ligand complex, pi-pi stacking interaction, Polymers, Secondery Building Unit, Structural data, Supramolecular framework, Ternare Komplexe, X-ray diffraction}, issn = {0022-2860}, doi = {10.1016/j.molstruc.2017.06.128}, author = {Singh, Sandeep K. and Srivastava, Ashish Kumar and Srivastava, Krishna and Banerjee, Rahul and Prasad, Jagdish} } @article {47319, title = {Boron nitride and oxide supported on dendritic fibrous nanosilica for catalytic oxidative dehydrogenation of propane}, journal = {ACS Sustainable Chemistry \& Engineering}, volume = {8}, year = {2020}, month = {NOV }, pages = {16124-16135}, type = {Article}, abstract = {

In this work, we were able to significantly increase the activity of boron nitride (BN) catalysts used for the oxidative dehydrogenation (ODH) of propane by designing and synthesizing BN supported on dendritic fibrous nanosilica (DFNS). DFNS/BN showed a markedly increased catalytic efficiency, accompanied by exceptional stability and selectivity. Textural characterization, together with solid-state nuclear magnetic resonance (NMR) and X-ray photoelectron spectroscopic analyses, indicates the presence of a combination of unique fibrous morphology of DFNS and various boron sites connected to silica to be the reason for this increase in the catalytic performance. Notably, DFNS/B2O3 also showed catalytic activity, although with more moderate selectivity compared to that of DFNS/BN. Solid-state NMR spectra indicate that the higher selectivity of DFNS/BN might stem from a larger amount of hydrogen-bonded hydroxyl groups attached to B atoms. This study indicates that both boron nitride and oxide are active catalysts and by using high surface area support (DFNS), conversion from propane to propene as well as productivity of olefins was significantly increased.

}, keywords = {Electron microscopy, heterogeneous catalysis, Nanostructures, NMR spectroscopy, propane dehydrogenation, X-ray diffraction, X-ray photoelectron spectroscopy}, issn = {2168-0485}, doi = {10.1021/acssuschemeng.0c04148}, author = {Belgamwar, Rajesh and Rankin, Andrew G. M. and Maity, Ayan and Mishra, Amit Kumar and Gomez, Jennifer S. and Trebosc, Julien and Vinod, Chathakudath P. and Lafon, Olivier and Polshettiwar, Vivek} } @article {47631, title = {Construction of two-component chemically reactive supramolecular assemblies-acyl migration reactions in cocrystals of napthalene-2,3-diol and its diesters}, journal = {ChemPlusChem}, volume = {86}, year = {2021}, month = {AUG}, pages = {1128-1134}, type = {Article}, abstract = {Reactions in solids are of contemporary interest due to applications in pharmaceutical industries to environmental sustainability. Although several reactive crystals that support chemical reactions have been identified and characterized, the same cannot be said about reactive cocrystals. Earlier we correlated the facile acyl group transfer reactions in crystals with supramolecular parameters obtained from the crystal structures. The structure-reactivity correlation revealed the requirement of proper juxtaposition of electrophile (C=O) and the nucleophile (OH) with distance (similar to 3.2 angstrom) and angle (similar to 90 degrees) along the chain structure. The current article describes the preparation of cocrystals that are capable of supporting intermolecular acyl group transfer reactions in a group of structurally similar molecules. The cocrystals of naphthalene 2,3-diol and its corresponding diesters showed a facile solid state acyl transfer reaction, which has been well correlated with their crystal structures.}, keywords = {Acylation, domino reactions, intermolecular interactions, reaction in cocrystal, solid-state reactions, X-ray diffraction}, issn = {2192-6506}, doi = {10.1002/cplu.202100139}, author = {Bahadur, Vir and Gonnade, Rajesh G. and Tamboli, I. Majid and Krishnaswamy, Shobhana and Shashidhar, Mysore S.} } @article {48395, title = {Green synthesis-mediated iron oxide nanoparticles using sphagneticola trilobata (L.) for antibacterial and anticancer assessment}, journal = {Pharmacognosy Magazine}, volume = {18}, year = {2022}, month = {OCT-DEC}, pages = {953-961}, type = {Article}, abstract = {

Background: Green chemistry is widely accepted phenomenon to synthesize iron oxide nanoparticles (Fe-NPs) used in several biomedical and technological applications. Metal oxide nanoparticles are useful in biomedical, clearing environmental pollutants, enzyme immobilization, etc., Objectives: The synthesis of Fe-NPs using Sphagneticola trilobata leaf extract using ferric chloride solution and its biological assessment. Materials and Methods: The present study involved the synthesis of Fe-NPs using S. trilobata leaf extract using ferric chloride solution by the co-precipitation method. The synthesized nanoparticles were characterized for Fourier-transform infrared spectroscopy, scanning electron microscopy, powder X-ray diffraction spectroscopy, particle size analysis, and magnetization studies. The nanoparticles were biologically evaluated for microbiological, antioxidant, and in vitro cytotoxicity activity. Results: Magnetic nanoparticles were appeared in dark brown color. The change in color might result due to the presence of polyphenols in S. trilobata leaf extract. The characterization studies confirmed morphology, shape, and size of the nanoparticles. The mean diameter of Fe-NPs and S. trilobata-Fe-NPs was found to be 42.2 +/- 2.6 and 62.54 +/- 2.01 nm, respectively. Magnetization studies of nanoparticles revealed ferromagnetic behavior with the saturation magnetization at 57 emugm(-1). S. trilobata-Fe-NPs showed significant antibacterial action against Staphylococcus aureus and Bacillus subtilis by the well-diffusion method. Antioxidant activity of S. trilobata-Fe-NPs exhibited 65.78\% inhibition in comparison with ascorbic acid. The cytotoxicity assay of S. trilobata-Fe-NPs on HCT-15 colon adenocarcinoma cells showed significant anticancer activity (56.44\%) cytotoxic inhibition. Conclusion: Green synthesis-mediated S. trilobata-Fe-NPs appeared to produce significant antimicrobial and anticancer potential.

}, keywords = {Elemental analysis, field emission scanning electron microscopy, green synthesis, iron oxide nanoparticles, Sphagneticola trilobata, X-ray diffraction}, issn = {0973-1296}, doi = {10.4103/pm.pm_356_21}, author = {Dhavale, Rakesh Pandit and Patil, Swapnil Sanjay and Jadhav, Sagar Ujwal and Dhavale, Rushikesh Pandit and Agawane, Sachin Bharat} } @article {48738, title = {Six-membered NHC stabilized monomeric zinc complexes}, journal = {European Journal of Inorganic Chemistry}, volume = {26}, year = {2023}, month = {JUL}, pages = {e202300167}, type = {Article}, abstract = {

This paper describes the rare use of a 6-membered saturated N-heterocyclic carbene (NHC) known as 1,3-di(2,6-diisopropylphenyl) tetrahydropyrimidine-2-ylidene (abbreviated as 6-SI-Dipp) as a ligand in zinc chemistry. We report on the investigation of the reactions between 6-SI-Dipp and ZnX2, which resulted in a range of new monomeric 6-SIDipp center dot ZnX2 complexes (X=Et (1), Cl (2), Br (3), and I (4)). We also prepared a new NHC zinc complex where the two substituents of the zinc atom are different, 6-SIDipp center dot Zn(Et)Br (7) through the reaction of the proligand [6-SIDippH]Br with ZnEt2. We have observed that the reactions of complex 1 with sulfur and HBpin led to the removal of the ZnEt2 moiety, resulting in the formation of a C=S double bond and a B H activation product, respectively. Lastly, the reaction of 1 with five-membered NHCs led to the exchange of carbene and the formation of either 5-IDipp center dot ZnEt2 (8) or 5-SIDipp center dot ZnEt2 (9).

}, keywords = {Lewis adduct, NHC, X-ray diffraction, zinc}, issn = {1434-1948}, doi = {10.1002/ejic.202300167}, author = {Gour, Kritika and Kundu, Gargi and Dash, Soumya Ranjan and Vanka, Kumar and Tothadi, Srinu and Sen, Sakya S.} }