@article {46740, title = {Effect of bio-filler on hybrid sisal-banana-kenaf-flax based epoxy composites: a statistical correlation on flexural strength}, journal = {Journal of Bionic Engineering}, volume = {17}, year = {2020}, month = {NOV}, pages = {1263-1271}, type = {Article}, abstract = {

This work deals with the investigation of the synergistic effect of bagasse ash with sisal-banana-kenaf-flax fibers reinforced epoxy composite for their flexural behavior. The composites with three combinations of hybrid fibers viz. sisal/kenaf (HSK), banana/kenaf (HBK), and banana/flax (HBF) with bagasse ash (BGA) as filler material are fabricated using vacuum bag assisted resin transfer molding. Experiments were conducted based on L27 orthogonal array to understand the influence of control factor viz. fiber volume, alkali concentration \& BGA over output response.X-ray micro computed tomography analysis was conducted over the developed sample to infer the uniform dispersion of fiber and filler material. The experimental results reveal that the addition of fiber up to 30 vol\% depicts better strength and further addition results in a negative impact. Increasing in order of BGA decreases the flexural strength of the developed composites.

}, keywords = {bagasse ash, flexural strength, natural fiber, vacuum bag assisted resin transfer molding, X-ray micro computed tomography}, issn = {1672-6529}, doi = {10.1007/s42235-020-0083-7, Early Access Date = AUG 2020}, author = {Vivek, Somasundaram and Kanthavel, Karuppusamy and Torris, Arun and Kavimani, Vijayananth} } @article {46836, title = {Enhancing the mechanical properties of 3D printed polylactic acid using nanocellulose}, journal = {Polymer Engineering and Science}, volume = {60}, year = {2020}, month = {AUG}, pages = {1842-1855}, type = {Article}, abstract = {

We report here a systematic investigation of the mechanical properties of polylactic acid (PLA) processed by fused filament fabrication (FFF) 3D printing vs PLA processed by compression molding. Our results show that the tensile strength and modulus of FFF-PLA is 49\% and 41\% lower, respectively, than compression molded samples of PLA. We also demonstrate here an approach to augment the mechanical properties of 3D printed PLA using nanocellulose. Incorporation of a small quantity (1 wt\%) of cellulose nanofibers (CNF) was found to enhance the tensile strength and modulus of 3D printed PLA by 84\% and 63\%, respectively. X-ray microtomography was used to probe the morphology of 3D printed PLA and PLA/CNF composites. 3D printed PLA/CNF composites had significantly lesser voids as compared to neat 3D printed PLA. Differential scanning calorimetry study revealed that CNF can accelerate the nucleation and crystallization of 3D printed PLA leading to enhanced crystallinity. The thermal stability of 3D printed PLA/CNF composites was not compromised by the addition of CNF. The enhanced mechanical properties of 3D printed PLA/CNF composites can be ascribed to higher crystallinity and lesser defects.

}, keywords = {3D printing, Biocomposites, composites, fused filament fabrication (FFF), Nanocellulose, polylactic acid (PLA)}, issn = {0032-3888}, doi = {10.1002/pen.25421, Early Access Date = JUN 2020}, author = {Ambone, Tushar and Torris, Arun and Shanmuganathan, Kadhiravan} } @article {47357, title = {Elastic piezoelectric aerogels from isotropic and directionally ice-templated cellulose nanocrystals: comparison of structure and energy harvesting}, journal = {Cellulose}, volume = {28}, year = {2021}, month = {JUL}, pages = {6323-6337}, type = {Article}, abstract = {

We report the preparation of highly compressible and elastic piezoelectric aerogels of carboxylated cellulose nanocrystals (CNCs). Aqueous CNC dispersions containing polyethyleneimine and crosslinker were frozen isotropically to yield isotropic aerogels, while oriented aerogels were prepared by directional freezing. These aerogels were highly flexible and porous (similar to 85\% void fraction), exhibiting greater than 90\% recovery at 50\% compressive strain even after 100 compression-decompression cycles. Since such aerogels with low bulk modulus and high anisotropy would be an ideal platform for leveraging the piezoelectric properties of CNCs, we used them to prepare piezoelectric nanogenerator devices and determined their energy transduction behavior. Anisotropic aerogels led to an enhanced open-circuit voltage of 840 mV (at similar to 8 N applied force), which is over 2.6 times higher than isotropic aerogels (320 mV). The energy density of anisotropic aerogels was around 52 nW/cm(2), representing outstanding piezoelectric performance for cellulose-based aerogels. Such aerogels with high compressibility, elastic recovery and exceptional piezoelectric performance could have potential applications in sensors, wearable electronics, etc.

}, keywords = {Aerogel, Anisotropic, Cellulose nanocrystals, energy harvesting, Piezoelectricity}, issn = {0969-0239}, doi = {10.1007/s10570-021-03896-6, Early Access Date = MAY 2021}, author = {Ram, Farsa and Biswas, Bipul and Torris, Arun and Kumaraswamy, Guruswamy and Shanmuganathan, Kadhiravan} }