@article { ISI:000257349100007, title = {Silicate nanoparticles by bioleaching of glass and modification of the glass surface}, journal = {Journal of Non-Crystalline Solids}, volume = {354}, number = {29}, year = {2008}, month = {JUL}, pages = {3433-3437}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

Bioleaching is examined as a low temperature (50 degrees C) soft chemical approach to nanosynthesis and surface processing. We demonstrate that fungus based bioleaching of borosilicate glass enables synthesis of nearly monodispersed ultrafine (similar to 5 +/- 0.5 nm) silicate nanoparticles. Using various techniques such as X-ray diffraction, X-ray photoelectron spectroscopy and FTIR we compare the constitution and composition of the nanoparticles with that of the parent glass, and establish the basic similarities between the two. The bioleaching process is shown to enhance the non-bridging oxygen component and correspondingly influence the Si-O-Si network. The root mean square roughness of glass surface is seen to increase from 1.27 nm for bare glass to 2.52 nm for 15 h fungal processed case, this increase being equivalent to that for glass annealed at 500 degrees C. (c) 2008 Elsevier B.V. All rights reserved.

}, keywords = {Bioglass, Biomaterials, borosilicates, narroparticles}, issn = {0022-3093}, doi = {10.1016/j.jnoncrysol.2008.03.025}, author = {Kulkarni, Sneha and Syed, Asad and Singh, Sanjay and Gaikwad, Anil and Patil, Kashinath and Vijayamohanan, K. and Ahmad, Absar and Ogale, Satishchandra} } @article { ISI:000270363600029, title = {Enhanced conversion efficiency in dye-sensitized solar cells based on hydrothermally synthesized TiO2-MWCNT nanocomposites}, journal = {ACS Applied Materials \& Interfaces}, volume = {1}, number = {9}, year = {2009}, month = {SEP}, pages = {2030-2035}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

A 50 \% enhancement in the conversion efficiency (4.9-7.37 \%) is realized in dye-sensitized solar cells Using hydrothermally synthesized TiO2-multiwalled carbon nanotube (MWCNT) nanocomposites as compared to hydrothermally synthesized TiO2 without MWCNT and Degussa P25. Several characterizations have been employed to reveal the nature of the modification imparted to the MWCNTs under hydrothermal processing conditions and the resulting TiO2-MWCNT conjugation through -COOH groups. Efficient charge transfer In the nanocomposite and efficient electron transport by MWCNT (significantly higher Incident-photon-to-current conversion efficiency) are suggested to be the possible reasons for the enhancement.

}, keywords = {Carbon nanotubes, charge transfer, Dye-sensitized solar cells, Hybrid composite, hydrothermal}, issn = {1944-8244}, doi = {10.1021/am900396m}, author = {Muduli, Subas and Lee, Wonjoo and Dhas, Vivek V. and Mujawar, Sarfraj and Dubey, Megha and Vijayamohanan, K. and Han, Sung-Hwan and Ogale, Satishchandra} } @article { ISI:000263397900005, title = {Manipulation of magnetic nanostructures through low temperature metal-oxygen chemistry: Co/CoO exchange biased nanodonuts and Co nanotips}, journal = {Solid State Communications}, volume = {149}, number = {7-8}, year = {2009}, month = {FEB}, pages = {277-280}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

Dense nanodonut and nanotip type morphologies are shown to self-evolve in Ultrathin cobalt films during growth under Vacuum, depending oil the level of oxygen incorporation and temperature. The nanodonut morphology forms at room temperature and the corresponding magnetic hysteresis shows exchange bias (similar to 35 Oe shift along the field axis), which is attributed to the presence of CoO and its exchange Coupling with cobalt. The morphology evolves into nanotip features with increase of growth temperature, with Concurrent elimination of the oxide component and exchange bias. (C) 2008 Elsevier Ltd. All rights reserved.

}, keywords = {Co/CoO, Magnetic film, self assembly, Vacuum evaporation}, issn = {0038-1098}, doi = {10.1016/j.ssc.2008.12.019}, author = {Phase, Deodatta and Choudhary, Ram Janay and Ganesan, V. and Reddy, V. Raghvendra and Gupta, Ajay and Selvi, N. and Kulkarni, Sneha and Ogale, Satishchandra} } @article { ISI:000264095500002, title = {Parametric dependence studies on cracking of clay}, journal = {Physica A-Statistical Mechanics and its Applications}, volume = {388}, number = {8}, year = {2009}, month = {APR}, pages = {1352-1358}, publisher = {ELSEVIER SCIENCE BV}, address = {PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS}, abstract = {

We have studied the shrinkage-crack patterns formed in the process of drying of clay/water slurries employing simple laboratory experiments. Both isotropic and directional drying was studied. The objective has been to examine the correlation between the solvent, materials parameters and the crack patterns. Attempt is made to fit the observations to specific models. The dynamics of the pattern formation process and the geometric properties of the crack patterns are found to be in conformity with the hydrodynamic model by Lee and Routh [W.P. Lee, A.F. Routh, Langmuir 20 (2004) 9887]. (C) 2008 Elsevier B.V. All rights reserved.

}, keywords = {clay, Cracks pattern, Hydrodynamic model}, issn = {0378-4371}, doi = {10.1016/j.physa.2008.12.039}, author = {Pasricha, Kanika and Wad, Uday and Pasricha, Renu and Ogale, Satishchandra} } @article { ISI:000275706100023, title = {Elucidation of the role of hexamine and other precursors in the formation of magnetite nanorods and their stoichiometry}, journal = {Physical Chemistry Chemical Physics}, volume = {12}, number = {13}, year = {2010}, month = {FEB}, pages = {3246-3253}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

Hexamine is known to assist anisotropic growth of metal oxides and the same is also found to be true for magnetite nanosynthesis. In this work we elucidate the role of hexamine and other precursors in the formation of magnetite nanorods by the hydrothermal route and their stoichiometry. Various others hydrolyzing agents such as sodium hydroxide (NaOH), sodium hydroxide + hexamine, ammonia (NH(3)), ammonia + formaldehyde are also studied. The synthesized nanoparticles are characterized with the help of various techniques such as X-ray diffraction (XRD), FT-IR spectroscopy, UV-VIS-NIR spectroscopy, transmission electron microscopy (TEM), Mossbauer spectroscopy and SQUID magnetization measurements. It is found that only when ferric chloride, ferrous ammonium sulfate (FAS) and hexamine are used, well defined nanorods are formed. When sodium hydroxide and hexamine are used as a hydrolyzing system nearly spherical nanoparticles with small size (similar to 13 nm) are formed, as compared to the case of sodium hydroxide alone which leads to bigger cube like nanoparticles. Interestingly the decomposition products of hexamine do not lead to nanorod formation. Thus, slow decomposition of hexamine at elevated temperature and the consequent slow rise in pH is the key to the anisotropic growth of the iron oxide system.

}, issn = {1463-9076}, doi = {10.1039/b917407a}, author = {Singh, Hema and Bhagwat, Shrikant and Jouen, Samuel and Lefez, Benoit and Athawale, Anjali A. and Hannoyer, Beatrice and Ogale, Satishchandra} } @article { ISI:000293518300007, title = {From graphite oxide to highly water dispersible functionalized graphene by single step plant extract-induced deoxygenation}, journal = {Green Chemistry}, volume = {13}, number = {8}, year = {2011}, month = {JUL}, pages = {1990-1996}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

We report a single step facile synthesis of highly water dispersible functionalized graphene nanosheets by plant extract-induced deoxygenation of graphite oxide (GO). The results of various characterizations reveal that the properties of such plant extract-converted graphene nanosheets (PCGN) are comparable to chemically converted graphene nanosheets (CCG). These results open a green route to the emerging graphene-based technologies.

}, issn = {1463-9262}, doi = {10.1039/c1gc15393e}, author = {Mhamane, Dattakumar and Ramadan, Wegdan and Fawzy, Manal and Rana, Abhimanyu and Dubey, Megha and Rode, Chandrashekhar and Lefez, Benoit and Hannoyer, Beatrice and Ogale, Satishchandra} } @article { ISI:000311056800010, title = {3D Hexaporous carbon assembled from single-layer graphene as high performance supercapacitor}, journal = {Chemsuschem}, volume = {5}, number = {11}, year = {2012}, month = {OCT}, pages = {2159-2164}, publisher = {WILEY-V C H VERLAG GMBH}, type = {Article}, address = {BOSCHSTRASSE 12, D-69469 WEINHEIM, GERMANY}, keywords = {Electrochemistry, Energy storage, graphene, porous materials, Supercapacitors}, issn = {1864-5631}, doi = {10.1002/cssc.201200421}, author = {Yadav, Prasad and Banerjee, Abhik and Unni, Sreekuttan and Jog, Jyoti Prakash and Kurungot, Sreekumar and Ogale, Satishchandra} } @article { ISI:000299292600009, title = {Enhanced piezoresponse of electrospun PVDF mats with a touch of nickel chloride hexahydrate salt}, journal = {Nanoscale}, volume = {4}, number = {3}, year = {2012}, month = {FEB}, pages = {752-756}, publisher = {ROYAL SOC CHEMISTRY}, type = {Article}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

PVDF nanofibers are prepared using electrospinning. The effect of addition of a hydrated salt, nickel chloride hexahydrate (NiCl2 center dot 6H(2)O), on the phase formation is examined. Addition of the hydrated salt (NC) is found to enhance the polar beta phase by about 30\%. The peak to peak piezo-voltage generated for PVDF NC is almost 0.762 V, a factor of 3 higher than that for PVDF. The fiber mats exhibit a significantly enhanced dynamic strain sensor response. The voltage generated per unit micro-strain developed during the free vibration test for PVDF was 0.119 mV whereas it was 0.548 mV for PVDF NC, exhibiting a non-linearly enhanced performance vis a vis the increase in the beta phase component.

}, issn = {2040-3364}, doi = {10.1039/c2nr11841f}, author = {Dhakras, Dipti and Borkar, Vivek and Ogale, Satishchandra and Jog, Jyoti Prakash} } @article { ISI:000302639600011, title = {Quantum dot bio-conjugate: as a western blot probe for highly sensitive detection of cellular proteins}, journal = {Journal of Nanoparticle Research}, volume = {14}, number = {3}, year = {2012}, month = {MAR}, pages = {732}, publisher = {SPRINGER}, address = {VAN GODEWIJCKSTRAAT 30, 3311 GZ DORDRECHT, NETHERLANDS}, abstract = {

In the present study, we report a quantum dot (QD)-tailored western blot analysis for a sensitive, rapid and flexible detection of the nuclear and cytoplasmic proteins. Highly luminescent CdTe and (CdTe) ZnS QDs are synthesized by aqueous method. High resolution transmission electron microscopy, Raman spectroscopy, fourier transform infrared spectroscopy, fluorescence spectroscopy and X-ray diffraction are used to characterize the properties of the quantum dots. The QDs are functionalized with antibodies of prostate apoptosis response-4 (Par-4), poly(ADP-ribose) polymerases and beta actin to specifically bind with the proteins localized in the nucleus and cytoplasm of the cells, respectively. The QD-conjugated antibodies are used to overcome the limitations of conventional western blot technique. The sensitivity and rapidity of protein detection in QD-based approach is very high, with detection limits up to 10 pg of protein. In addition, these labels provide the capability of enhanced identification and localization of marker proteins in intact cells by confocal laser scanning microscopy.

}, keywords = {Detection, Imaging, nanomedicine, quantum dot, Rapid, sensors, Western blot}, issn = {1388-0764}, doi = {10.1007/s11051-012-0732-9}, author = {Kale, Sonia and Kale, Anup and Gholap, Haribhau and Rana, Abhimanyu and Desai, Rama and Banpurkar, Arun G. and Ogale, Satishchandra and Shastry, Padma} } @article { ISI:000316691100012, title = {Fluorescent sophorolipid molecular assembly and its magnetic nanoparticle loading: a pulsed laser process}, journal = {Green Chemistry}, volume = {15}, number = {4}, year = {2013}, month = {JAN}, pages = {943-953}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

We report realization of strong green fluorescence in a fully biocompatible highly spherical mesoscale molecular assembly of sophorolipid created by pulsed UV laser processing of a water-based dispersion of sophorolipid. Remarkably, the said fluorescence is totally absent in the original molecule of sophorolipid and is thus the property of the pulsed laser induced modifications in the molecule and the assembly. We have separately examined the consequences of laser irradiation for glucose and oleic acid components which form the sophorolipid. This fluorescence character appears to be driven by the oleic acid component while the assembly process is assisted by the glucose component. Importantly the laser synthesized mesostructures can be easily redispersed in an aqueous medium after being dried and can also be loaded with magnetic nanoparticles (magnetite) for inducing the hyperthermia effect.

}, issn = {1463-9262}, doi = {10.1039/c3gc40108a}, author = {Singh, Pradeep Kumar and Mukherji, Ruchira and Joshi-Navare, Kasturi and Banerjee, Abhik and Gokhale, Rohan and Nagane, Satyawan and Prabhune, Asmita and Ogale, Satishchandra} } @article { ISI:000331413700027, title = {3D micro-porous conducting carbon beehive by single step polymer carbonization for high performance supercapacitors: the magic of in situ porogen formation}, journal = {Energy \& Environmental Science}, volume = {7}, number = {2}, year = {2014}, month = {FEB}, pages = {728-735}, publisher = {ROYAL SOC CHEMISTRY}, type = {Article}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

We report non-templated synthesis of interconnected microporous carbon (IMPC) sheets having beehive morphology by direct pyrolysis of poly(acrylamide-co-acrylic acid) potassium salt in inert atmosphere without any activation. The presence of the alkali metal in the selected polymer precursor results in a high specific surface area of 1327 m(2) g(-1). Importantly, 80\% of the pore volume is contributed by micropores with pore size ranging from 1-2 nm which is ideal for use as an electrode for supercapacitors. Whereas the rest of the surface area was contributed by a small fraction of mesopores and macropores due to the interconnected structure. The presence of three different types of pores make the material ideal for supercapacitor electrodes. IMPC was tested as an electrode in both aqueous and non-aqueous supercapacitors. All the aqueous measurements were done in 1 M H2SO4 solution with a potential window 1 V. A specific capacitance of 258 F g(-1) was realized at a constant charge-discharge current of 0.5 A g(-1) and it maintained at a value of 150 F g(-1) at 30 A g(-1). A long cycle stability of 90\% capacitance retention was observed after 5000 charge-discharge cycles at a current density of 2 A g(-1). At the highest power density 13 600 W kg(-1) the energy density was found to be 3.1 W h kg(-1). Non aqueous performance was tested in the presence of 1 M LiPF6 in ethylene carbonate-di-methyl carbonate with 5 mg active material loading. A specific capacitance of 138 F g(-1) was obtained at a current density of 0.25 A g(-1) and it retained at a value of 100 F g-1 at 10 A g(-1). The material can deliver an energy density of 31 W h kg(-1) at its highest power density of 11 000 W kg(-1) in a two electrode system based on active material loading.

}, issn = {1754-5692}, doi = {10.1039/c3ee42551g}, author = {Puthusseri, Dhanya and Aravindan, Vanchiappan and Madhavi, Srinivasan and Ogale, Satishchandra} } @article { ISI:000340703000039, title = {CH3NH3PbI(3-x)(BF4)(x): molecular ion substituted hybrid perovskite}, journal = {Chemical Communications}, volume = {50}, number = {68}, year = {2014}, month = {SEP}, pages = {9741-9744}, publisher = {ROYAL SOC CHEMISTRY}, type = {Article}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

A molecular ion (BF4-) substituted hybrid perovskite CH3NH3PbI(3-x)(BF4)(x) is synthesized. The substituted perovskite shows significant enhancement in electrical conductivity at low frequencies and improved photoresponse under AM1.5 illumination as compared to the perovskite (CH3NH3PbI3).

}, issn = {1359-7345}, doi = {10.1039/C4CC04537H}, author = {Nagane, Satyawan and Bansode, Umesh P. and Game, Onkar S. and Chhatre, Shraddha and Ogale, Satishchandra} } @article { ISI:000334898800032, title = {Electronically and catalytically functional carbon cloth as a permeable and flexible counter electrode for dye sensitized solar cell}, journal = {Electrochimica Acta}, volume = {123}, year = {2014}, month = {MAR}, pages = {248-253}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

In this work we demonstrate that a conducting carbon cloth obtained by one-step pyrolysis of easily available cellulose fabric competes favorably with the commonly employed expensive platinum/FTO system as a counter electrode for dye sensitized solar cell (DSSC). In view of the low carbonization temperature (1000 degrees C) which forbids full graphitization, the nature of carbon in this case is represented by topologically randomly assembled nanoscale graphene units (turbostratic carbon). This morphology has high density of edge states and oxygen containing surface groups rendering multitude of catalytic sites for the reduction of I-3(-). Moreover the cloth is permeable to the dye and/or liquid electrolyte and its absorption properties also help retain the electrolyte. A fairly high efficiency of 5.8\% is achieved using such cloth as a counter electrode as against 7\% with the conventional Pt/FTO system. Moreover, the permeable property of the cloth eliminates a complete step of drilling hard TCO substrates for final dispensing of electrolyte into the device and the sealing process is also facile. In fact even the dye can be dispensed through the cloth. Finally, the flexibility of the carbon cloth can adapt easily to flexible/wearable DSSC designs. (C) 2014 Elsevier Ltd. All rights reserved.

}, keywords = {conducting carbon cloth, counter electrode, DSSC, without drilling}, issn = {0013-4686}, doi = {10.1016/j.electacta.2013.12.175}, author = {Tathavadekar, Mukta and Biswal, Mandakini and Agarkar, Shruti A. and Giribabu, Lingamallu and Ogale, Satishchandra} } @article { ISI:000337783800074, title = {Enhanced capacitance retention in a supercapacitor made of carbon from sugarcane bagasse by hydrothermal pretreatment}, journal = {Energy \& Fuels}, volume = {28}, number = {6}, year = {2014}, month = {JUN}, pages = {4233-4240}, publisher = {AMER CHEMICAL SOC}, type = {Article}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

A unique morphology-controlling protocol involving hydrothermal preprocessing before pyrolysis is presented to convert cellulosic waste in the form of sugarcane bagasse into three-dimensional (3D) interconnected, conducting, and high surface area carbon nanochannels. The large buffer spaces in such a porous carbon sample yield impressive electrochemical capacitance (C-sp) of 280 F/g at a current density of 1 A/g (and 275 F/g at 5 mV/s), with 72\% retention even at a very high current density of 20 A/g. In contrast, the non-hydrothermally treated sample exhibits a C-sp value of 180 F/g at 1 A/g and only 52\% retention at 20 A/g. The much better performance of the hydrothermally preprocessed bagasse-derived carbon (BHAC) can be ascribed to the solvent retention inside the buffer spaces created, negating the diffusional limitations of pore inaccessibility at higher scan rates. The BHAC has a high surface area of 1260 m(2)/g with a fairly good (11 wt \%) concentration of oxygen functionality. The material renders a good energy density of Wh/kg at a power density of 3.5 kW/kg and shows good cyclability of 90\% after 1000 charge/discharge cycles.

}, issn = {0887-0624}, doi = {10.1021/ef500342d}, author = {Wahid, Malik and Puthusseri, Dhanya and Phase, Deodatta and Ogale, Satishchandra} } @article { ISI:000327771500117, title = {Evaluation of n-type ternary metal oxide NiMn2O4 nanomaterial for humidity sensing}, journal = {Sensors and Actuators B-Chemical}, volume = {191}, year = {2014}, month = {FEB}, pages = {837-843}, publisher = {ELSEVIER SCIENCE SA}, type = {Article}, address = {PO BOX 564, 1001 LAUSANNE, SWITZERLAND}, abstract = {

Synthesis of mono-dispersed oleic acid (OA) capped NiMn2O4 (NMO) nanoparticles and their use for humidity sensing is reported. Oleic acid capped NMO (NMO-cOA) nanoparticles are synthesized from nickel oleate and manganese oleate complex. NiMn2O4 is obtained by removing oleic acid capping at 500 degrees C in air. X-ray diffraction analysis shows formation of pure NiMn2O4 phase which is also confirmed by HRTEM-SAED analysis. The TEM analysis also shows that the nanoparticles are nearly mono-dispersed. Doctor bladed films of NMO nanoparticles are seen to exhibit excellent humidity sensing property. The resistivity is seen to change by two orders with humidity change from 11\% RH to 92\% RH with fairly good linearity over the entire range. The response and recovery times are also fast. (C) 2013 Elsevier B.V. All rights reserved.

}, keywords = {Humidity, Impedance, Nanoparticles, NiMn2O4, Oleic acid, Sensor}, issn = {0925-4005}, doi = {10.1016/j.snb.2013.10.071}, author = {Gawli, Yogesh and Badadhe, Satish S. and Basu, Aniruddha and Guin, Debanjan and Shelke, Manjusha V. and Ogale, Satishchandra} } @article { ISI:000345654000087, title = {From micron to nano-curcumin by sophorolipid co-processing: highly enhanced bioavailability, fluorescence, and anti-cancer efficacy}, journal = {RSC Advances}, volume = {4}, number = {104}, year = {2014}, month = {NOV}, pages = {60334-60341}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

Co-sonication of curcumin and acidic sophorolipid in aqueous solution is shown to lead to a dramatic enhancement of curcumin bioavailability through size reduction and encapsulation. The interaction between the two is studied and discussed based on optical absorption, photoluminescence, dynamic light scattering (DLS), zeta potential, FE-SEM, TEM, Infrared spectroscopy and X-ray diffraction measurements. The cytotoxicity effects of curcumin on breast cancer cell lines, MCF-7 and MDA-MB-231, are shown to be significantly enhanced by the formation of its complex with sophorolipid. The relative cytotoxicity of curcumin with its SL(A) complex is more due to the presence of the glucose moiety. The results further suggest that sophorolipid based formulations, which solubilize and nano-encapsulate curcumin after lipid digestion, show great potential for curcumin cell entry.

}, issn = {2046-2069}, doi = {10.1039/c4ra07300b}, author = {Singh, Pradeep Kumar and Wani, Kirtee and Kaul-Ghanekar, Ruchika and Prabhune, Asmita and Ogale, Satishchandra} } @article {46360, title = {From waste paper basket to solid state and Li-HEC ultracapacitor electrodes: a value added journey for shredded office paper}, journal = {Small}, volume = {10}, year = {2014}, month = {NOV}, pages = {4395-4402}, type = {Article}, abstract = {

Hydrothermal processing followed by controlled pyrolysis of used white office paper (a globally collectable shredded paper waste) are performed to obtain high surface area carbon with hierarchical pore size distribution. The BET specific surface area of such carbon is 2341 m 2 g(-1). The interconnected macroporous structure along with the concurrent presence of mesopores and micropores makes the material ideal for ultracapacitor application. Such waste paper derived carbon (WPC) shows remarkable performance in all solid-state supercapacitor fabricated with ionic liquid-polymer gel electrolyte. At room temperature, the material exhibits a power density of 19 000 W kg(-1) with an energy capability of 31 Wh kg(-1). The Li-ion electrochemical capacitor constructed using WPC as cathode also shows an excellent energy storage capacity of 61 Wh kg(-1)

}, issn = {1613-6810}, doi = {10.1002/smll.201401041}, author = {Puthusseri, Dhanya and Aravindan, Vanchiappan and Anothumakkool, Bihag and Kurungot, Sreekumar and Madhavi, Srinivasan and Ogale, Satishchandra} } @article { ISI:000345734800010, title = {Functionally engineered egg albumen gel for quasi-solid dye sensitized solar cells}, journal = {ACS Sustainable Chemistry \& Engineering}, volume = {2}, number = {12}, year = {2014}, month = {DEC}, pages = {2707-2714}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

In this report, we demonstrated an interesting application of a bioderived material for the dye sensitized solar cells (DSSCs). Egg white, the clear liquid in a hen{\textquoteright}s egg, which possesses a remarkable gelling/cross-linking ability, was applied in the form of a gel electrolyte in a DSSC architecture to enhance its durability. A hybrid gel composed of poly(acrylic acid), polyaniline and egg albumen was synthesized, and the cell efficiency, stability and durability of the corresponding DSSC device were studied in detail. The dye sensitized solar cell with the egg albumen based electrolyte demonstrated a conversion energy efficiency of 4.6\%. Further, a chemically modified egg albumen with ethylenediaminetetraacetic dianhydride showed improved cross-linking, microstructural and conductivity properties of the gel, and yielded a remarkable 5.75\% conversion efficiency. Electrochemical impedance spectroscopy data showed favorable characteristics for charge transport through the modified gel and supported the efficiency observations very well.

}, keywords = {dye sensitized solar cells, Egg albumen, gel electrolyte}, issn = {2168-0485}, doi = {10.1021/sc5004488}, author = {Kelkar, Sarika A. and Pandey, Komal and Agarkar, Shruti A. and Saikhedkar, Nidhi and Tathavadekar, Mukta and Agrawal, Ishita and Gundloori, Rathna V. N. and Ogale, Satishchandra} } @article { ISI:000342766500050, title = {High performance all-organic flexural piezo-FET and nanogenerator via nanoscale soft-interface strain modulation}, journal = {Physical Chemistry Chemical Physics}, volume = {16}, number = {41}, year = {2014}, month = {SEP}, pages = {22874-22881}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

Flexural strain fields are encountered in a wide variety of situations and invite novel device designs for their effective use in sensing, actuating, as well as energy harvesting (nanogenerator) applications. In this work we demonstrate an interesting all-organic device design comprising an electrospun P(VDF-TrFE) fiber-mat built directly on a conducting PANI film, which is also grown on a flexible PET substrate, for flexural piezo-FET and nanogenerator applications. Orders of magnitude stronger modulation of electrical transport in PANI film is realized in this device as compared to the case of a similar device but with a uniform spin-coated P(VDF-TrFE) film. We find that in the flexural mode of operation, the interaction between the laterally modulated nanoscale strain field distributions created by the fibers and the applied coherent strain field strongly influences the carrier transport in PANI. The transport modulation is suggested to occur due to strain-induced conformational changes in P(VDF-TrFE) leading to changes in carrier localization-delocalization. We further show that the fiber-mat based device system also works as an efficient nanogenerator capable of delivering power for low power applications.

}, issn = {1463-9076}, doi = {10.1039/c4cp02155j}, author = {Dhakras, Dipti and Gawli, Yogesh and Chhatre, Shraddha and Wadgaonkar, Prakash and Ogale, Satishchandra} } @article { ISI:000344978200061, title = {Hollow Co0.85Se nanowire array on carbon fiber paper for high rate pseudocapacitor}, journal = {ACS Applied Materials \& Interfaces}, volume = {6}, number = {21}, year = {2014}, month = {NOV}, pages = {18844-18852}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

A supercapacitor electrode is fabricated with Co0.85Se hollow nanowires (HNW) array, which is synthesized by wet chemical hydrothermal selenization of initially grown cobalt hydroxyl carbonate nanowires on conductive CFP. The dense self-organized morphology of Co0.85Se HNWs is revealed by scanning/transmission electron microscopy. The as-synthesized Co0.85Se HNWs possess high pseudocapacitive property with high capacitance retention and high durability. The areal capacitance value is seen to vary from 929.5 to 600 mF cm(-2) (60\% retention) as the current density is increased from 1 to 15 mA cm(-2), an increase of a factor of 15. Based on mass loading, this corresponds to a very high gravimetric capacitance of 674 (for 2 mA cm(-2) or 1.48 Ag-1) and 444 Fg(1-) (for 15 mA cm(-2) or 11 A g(-1)) in a full-cell configuration with the Co0.85Se HNWs as cathode and activated carbon as anode (asymmetric configuration) promising results are obtained.

}, keywords = {asymmetric supercapacitor, carbon fiber paper, cobalt selenide, hydrothermal, pseudocapacitor, selenization}, issn = {1944-8244}, doi = {10.1021/am504333z}, author = {Banerjee, Abhik and Bhatnagar, Sumit and Upadhyay, Kush Kumar and Yadav, Prasad and Ogale, Satishchandra} } @article {46362, title = {Improving the energy density of Li-ion capacitors using polymer-derived porous carbons as cathode}, journal = {Electrochimica Acta}, volume = {130}, year = {2014}, month = {JUN }, pages = {766-770}, type = {Article}, abstract = {

High energy density Li-ion hybrid electrochemical capacitors (Li-HEC) are fabricated with 3 D architectured high surface area porous carbon (HSPC) derived from the poly(acrylamide-co-acrylic acid) potassium salt in a single step without any activating agent. The obtained HSPC exhibits high specific surface area of 1490 m(2) g(-1) and characterized with several analytical techniques. Li-HEC is fabricated with insertion type Li4Ti5O12 anode by adjusting the mass balance based on the single electrode performance with Li. The Li-HEC delivered the maximum energy density of similar to 55 Wh kg(-1), which is much higher than commercially available activated carbon (similar to 36 Wh kg(-1)). Further HSPC based Li-HEC delivered excellent cycleability and rendered similar to 87\% of initial value after 2000 cycles. (C) 2014 Elsevier Ltd. All rights reserved.

}, keywords = {energy density, Li-ion hybrid electrochemical capacitors, non-aqueous, porous carbon}, issn = {0013-4686}, doi = {10.1016/j.electacta.2014.03.079}, author = {Puthusseri, Dhanya and Aravindan, Vanchiappan and Madhavi, Srinivasan and Ogale, Satishchandra} } @article { ISI:000345226100028, title = {Indanthrone derived disordered graphitic carbon as promising insertion anode for sodium ion battery with long cycle life}, journal = {Electrochimica Acta}, volume = {146}, year = {2014}, month = {NOV}, pages = {218-223}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

We report facile, one step synthesis of disordered graphitic carbon by high temperature (1000 degrees C) pyrolysis of indanthrone dye (ID). The pyrolysed carbon is disordered in nature and the same is clearly evidenced by various analytical techniques like X-ray diffraction, Raman spectroscopy and high resolution transmission electron microscopy. Na-insertion properties of such indanthrone dye derived disordered graphitic carbon (IDDGC) is evaluated in half-cell assembly (Na/IDDGC). The test cell delivered a reversible capacity of similar to 160 mAh g(-1) at current density of 25 mAg 1. In addition, excellent cycling profiles are noted for such IDDGC, which retains 67\% of initial reversible capacity after 500 cycles. The present study clearly highlights the importance of disorder in the graphitic carbon for efficient Na-ion storage. (C) 2014 Elsevier Ltd. All rights reserved.

}, keywords = {anode, disordered carbon, indanthrone, Na-ion battery}, issn = {0013-4686}, doi = {10.1016/j.electacta.2014.09.052}, author = {Suryawanshi, Anil and Mhamane, Dattakumar and Nagane, Satyawan and Patil, Shankar and Aravindan, Vanchiappan and Ogale, Satishchandra and Srinivasan, Madhavi} } @article {46404, title = {Large scale synthesis of graphene quantum dots (GQDs) from waste biomass and their use as an efficient and selective photoluminescence on-off-on probe for Ag+ ions}, journal = {Nanoscale}, volume = {6}, year = {2014}, month = {MAR}, pages = {11664-11670}, type = {Article}, abstract = {

Graphene quantum dots (GQDs) are synthesized from bio-waste and are further modified to produce amine-terminated GQDs (Am-GQDs) which have higher dispersibility and photoluminescence intensity than those of GQDs. A strong fluorescence quenching of Am-GQDs (switch-off) is observed for a number of metal ions, but only for the Ag+ ions is the original fluorescence regenerated (switch-on) upon addition of L-cysteine.

}, issn = {2040-3364}, doi = {10.1039/c4nr02494j}, author = {Suryawanshi, Anil and Biswal, Mandakini and Mhamane, Dattakumar and Gokhale, Rohan and Patil, Shankar and Guin, Debanjan and Ogale, Satishchandra} } @article {46402, title = {Low temperature grown CuBi2O4 with flower morphology and its composite with CuO nanosheets for photoelectrochemical water splitting}, journal = {Journal of Materials Chemistry A}, volume = {2}, year = {2014}, month = {MAR}, pages = {3661-3668}, type = {Article}, abstract = {

In this work we highlight a peculiar synthesis protocol for the p-type ternary metal oxide system of copper bismuth oxide (CuBi2O4), which yields a highly crystalline spherulitic morphology at a low temperature of 78 degrees C. We associate this growth with the hydrogen bonding effects imparted by the ethanol-water co-solvent system used for the synthesis. We present a detailed growth mechanism by evaluating different synthesis conditions systematically. Furthermore we show that upon the use of the non-stoichiometric (excess copper) precursor mixture under the same experimental conditions the growth of spherulitic CuBi2O4 changes the size and type of the spherulites. Interestingly, careful optimization of the nonstoichiometric synthesis presents a complete impediment to the spherulitic growth and produces a composite of nanorods of CuBi2O4 and nanosheets of CuO. This anisotropic nanocomposite shows an order of magnitude higher surface area as compared to spherulitic CuBi2O4. Since both CuBi2O4 and CuO are visible light absorbing p-type semiconductors, when the synthesized nanocomposite materials are examined as photoelectrochemical (PEC) photocathodes for water splitting, they show a remarkable dependence on the morphology and phase constitution. Almost 13-fold stronger PEC response is observed as the morphology changes from spherulites to nanorods.

}, issn = {2050-7488}, doi = {10.1039/c3ta14906d}, author = {Patil, Rupali and Kelkar, Sarika and Naphadeab, Rounak and Ogale, Satishchandra} } @article { ISI:000333567300064, title = {MOF-derived crumpled-sheet-assembled perforated carbon cuboids as highly effective cathode active materials for ultra-high energy density Li-ion hybrid electrochemical capacitors (Li-HECs)}, journal = {Nanoscale}, volume = {6}, number = {8}, year = {2014}, month = {FEB}, pages = {4387-4394}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

Lithium ion hybrid capacitors (Li-HECs) have attracted significant attention for use in next generation advanced energy storage technologies to satisfy the demand of both high power density as well as energy density. Herein we demonstrate the use of very high surface area 3D carbon cuboids synthesized from a metal-organic framework (MOF) as a cathode material with Li4Ti5O12 as the anode for high performance Li-HECs. The energy density of the cell is similar to 65 W h kg(-1) which is significantly higher than that achievable with commercially available activated carbon (similar to 36 W h kg(-1)) and a symmetric supercapacitor based on the same MOF-derived carbon (MOF-DC similar to 20 W h kg(-1)). The MOF-DC/Li4Ti5O12 Li-HEC assembly also shows good cyclic performance with similar to 82\% of the initial value (similar to 25 W h kg(-1)) retained after 10 000 galvanostatic cycles under high rate cyclic conditions. This result clearly indicates that MOF-DC is a very promising candidate for future P-HEVs in a Li-HEC configuration.

}, issn = {2040-3364}, doi = {10.1039/c4nr00025k}, author = {Banerjee, Abhik and Upadhyay, Kush Kumar and Puthusseri, Dhanya and Aravindan, Vanchiappan and Madhavi, Srinivasan and Ogale, Satishchandra} } @article { ISI:000337123100037, title = {Nanophase CulnS(2) nanosheets/CuS composite grown by the SILAR method leads to high performance as a counter electrode in dye sensitized solar cells}, journal = {RSC Advances}, volume = {4}, number = {42}, year = {2014}, month = {MAY}, pages = {21989-21996}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

Single phase CulnS(2) (CIS) nanosheets are synthesized on TiO2 coated FTO by the simple technique of Successive Ionic Layer Adsorption Reaction (SILAR) followed by annealing at 500 degrees C. Annealing at a lower temperature of 250 degrees C is found to yield CuS nanoparticles in addition to the CIS phase. Both single phase CIS and the CuS/CIS nanocomposite were examined as counter electrodes for a dye-sensitized solar cell (DSSC). The CIS-CuS composite is found to have a synergistic effect on the catalytic performance toward the reduction of tri-iodide, yielding a power conversion efficiency of 6.3\% as compared to pristine CIS (5\%) or CuS (3.5\%). The possible reasons behind the high performance of the composite are elucidated using cyclic voltammetry (CV) measurements and electrochemical impedance spectroscopy (EIS).

}, issn = {2046-2069}, doi = {10.1039/c4ra01740d}, author = {Bhosale, Reshma K. and Agarkar, Shruti A. and Agrawal, Ishita and Naphade, Rounak A. and Ogale, Satishchandra} } @article { ISI:000344132400051, title = {Oligomer-salt derived 3D, heavily nitrogen doped, porous carbon for Li-ion hybrid electrochemical capacitors application}, journal = {Carbon}, volume = {80}, year = {2014}, month = {DEC}, pages = {462-471}, publisher = {PERGAMON-ELSEVIER SCIENCE LTD}, address = {THE BOULEVARD, LANGFORD LANE, KIDLINGTON, OXFORD OX5 1GB, ENGLAND}, abstract = {

3D high surface area porous carbon is seen to form via self assembly of porous graphene sheets by direct pyrolysis of an oligomer salt tailored for the realization of molecular level activation. The oligomer salt was derived from 4-amino benzoic acid as the monomer by a facile free radical polymerization process. Incorporation of the functional groups (-COONa) eliminate the need for any external activating agents (KOH, ZnCl2, etc.) and also render high degree of sub-nanoscale homogeneity. This oligomer derived carbon (ODC) exhibits efficient performance in non-aqueous charge storage application namely Li-ion hybrid electrochemical capacitor (Li-HEC) owing to its high surface area, 3D interconnectivity and an appropriate pore size distribution. The Li-HEC fabricated with ODC based electrodes delivered a maximum energy density of similar to 63 Wh kg(-1) with spinel L4Ti5O12 as the anode. (C) 2014 Elsevier Ltd. All rights reserved.

}, issn = {0008-6223}, doi = {10.1016/j.carbon.2014.08.086}, author = {Gokhale, Rohan and Aravindan, Vanchiappan and Yadav, Prasad and Jain, Srashti and Phase, Deodatta and Madhavi, Srinivasan and Ogale, Satishchandra} } @article { ISI:000327845900029, title = {Orthorhombic/cubic Cd2SnO4 nanojunctions: enhancing solar water splitting efficiency by the suppression of charge recombination}, journal = {Journal of Materials Chemistry A}, volume = {2}, number = {2}, year = {2014}, month = {NOV}, pages = {492-499}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

The low practical efficiency of binary metal oxide semiconductor-based photo-electrochemical (PEC) water splitting has prompted researchers to examine ternary and quaternary oxides, which provide more leverage for engineering the desired PEC properties via stoichiometry (valence) and phase control. One ternary system of interest in this context is cadmium tin oxide (Cd2SnO4), which supports the cubic and orthorhombic phases with optical, electronic and catalytic properties that are favourable for PEC water splitting. However, its practical PEC performance is limited by high surface recombination of the photogenerated charge carriers. In this work we circumvent this problem by engineering the constitution of Cd2SnO4 nanoparticles to a biphasic nanojunction form, comprising of a nanocomposite of cubic and orthorhombic phases. The favourable conduction band alignment between the cubic and orthorhombic phases leads to a dramatic reduction in the recombination of the photogenerated charges, leading to a 10-fold increase (from 250 mu A cm(2) to over 2 mA cm(2)) in the photocurrent vis-a-vis the single cubic or orthorhombic phase performance. We discuss the underlying mechanism for the observed dramatic enhancement in the water splitting efficiency.

}, issn = {2050-7488}, doi = {10.1039/c3ta13851h}, author = {Deshpande, Aparna and Kelkar, Sarika A. and Rayalu, Sadhana and Ogale, Satishchandra} } @article {46370, title = {Plasmonic light harvesting of dye sensitized solar cells by Au-nanoparticle loaded TiO2 nanofibers}, journal = {Journal of Materials Chemistry A}, volume = {2}, year = {2014}, month = {FEB}, pages = {975-984}, type = {Article}, abstract = {

We report a significant enhancement in the performance of dye sensitized solar cells by using in situ Au nanoparticle (Au NP) loaded TiO2 nanofibers (Au: TiO2 NFs) as the light harvesting (LH) layer as compared to the use of only TiO2 nanofibers (NFs) as the LH layer. The Au NP: TiO2 nanofibers are prepared by electro-spinning of a precursor mixture whereby nanostructured porous TiO2 nanofibers are formed and get in situ loaded with only 4-5 nm AuNPs. The as-synthesized nanofibers are characterized by X-ray diffraction, Raman, photoluminescence (PL) and Mott-Schottky analyses. The presence of gold nanoparticles shows considerable improvements in light harvesting and the electrochemical properties of TiO2 nanofibers. A remarkable enhancement in the efficiency by 25\% is achieved with the AuNF LH layer as compared to 12\% with the NF layer, over the value without any light harvesting layer. The IPCE and impedance analyses reveal commensurate improvements. The impedance study shows a decrease in the transport resistance (R-TiO2) and an increment in the chemical capacitance and life time of the solar cell. Systematic analyses of the optical properties suggest that the enhanced light harvesting by Au NP loaded TiO2 nanofibers is caused by the role of plasmon-polariton modes at the distributed nanoscale Schottky junctions in the Au: TiO2 nanofibers.

}, issn = {2050-7488}, doi = {10.1039/c3ta13246c}, author = {Naphade, Rounak A. and Tathavadekar, Mukta and Jog, Jyoti P. and Agarkar, Shruti and Ogale, Satishchandra} } @article { ISI:000338011200013, title = {Scaling behavior of resistive switching in epitaxial bismuth ferrite heterostructures}, journal = {Advanced Functional Materials}, volume = {24}, number = {25}, year = {2014}, month = {JUL}, pages = {3962-3969}, publisher = {WILEY-V C H VERLAG GMBH}, address = {BOSCHSTRASSE 12, D-69469 WEINHEIM, GERMANY}, abstract = {

Resistive switching (RS) of (001) epitaxial multiferroic BiFeO3/La0.67Sr0.33MnO3/SrTiO3 heterostructures is investigated for varying lengths scales in both the thickness and lateral directions. Macroscale current-voltage analyses in conjunction with local conduction atomic force microscopy (CAFM) reveal that whilst both the local and global resistive states are strongly driven by polarization direction, the type of conduction mechanism is different for each distinct thickness regime. Electrode-area dependent studies confirm the RS is dominated by an interface mechanism and not by filamentary formation. Furthermore, CAFM maps allow deconvolution of the roles played by domains and domain walls during the RS process. It is shown that the net polarization direction, and not domain walls, controls the conduction process. An interface mechanism based on barrier height and width alteration due to polarization reversal is proposed, and the role of electronic reconstruction at the interface is further investigated.

}, issn = {1616-301X}, doi = {10.1002/adfm.201400110}, author = {Rana, Abhimanyu and Lu, Haidong and Bogle, Kashinath A. and Zhang, Qi and Vasudevan, Rama and Thakare, Vishal and Gruverman, Alexei and Ogale, Satishchandra and Valanoor, Nagarajan} } @article { ISI:000341779000037, title = {Surfactant free gram scale synthesis of mesoporous Ni(OH)(2)-r-GO nanocomposite for high rate pseudocapacitor application}, journal = {RSC Advances}, volume = {4}, number = {75}, year = {2014}, month = {AUG}, pages = {39875-39883}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

We report a single-step surfactant-free gram scale hydrothermal synthesis of mesoporous Ni(OH)(2) nanoparticles and the Ni(OH)(2)-reduced graphene oxide (Ni(OH)(2)-r-GO) nanocomposite. Interesting morphological features are noted. These nanomaterials are examined and compared as cathode materials for pseudo-capacitor application through detailed characterizations. A high specific capacitance (C-s) of 1538 F g(-1) is observed for Ni(OH)(2)-r-GO even at a high current density of 40 A g(-1), whereas at the same current rate, bare Ni(OH)(2) shows C-s of only 936 F g(-1).

}, issn = {2046-2069}, doi = {10.1039/c4ra06601d}, author = {Singh, Upendra and Banerjee, Abhik and Mhamane, Dattakumar and Suryawanshi, Anil and Upadhyay, Kush Kumar and Ogale, Satishchandra} } @article { ISI:000330779900044, title = {Synthesis of an efficient heteroatom-doped carbon electro-catalyst for oxygen reduction reaction by pyrolysis of protein-rich pulse flour cooked with SiO2 nanoparticles}, journal = {Physical Chemistry Chemical Physics}, volume = {16}, number = {9}, year = {2014}, month = {JAN}, pages = {4251-4259}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

Development of a highly durable, fuel-tolerant, metal-free electro-catalyst for oxygen reduction reaction (ORR) is essential for robust and cost-effective Anion Exchange Membrane Fuel Cells (AEMFCs). Herein, we report the development of a nitrogen-doped (N-doped) hierarchically porous carbon-based efficient ORR electrocatalyst from protein-rich pulses. The process involves 3D silica nanoparticle templating of the pulse flour(s) followed by their double pyrolysis. The detailed experiments are performed on gram flour (derived from chickpeas) without any in situ/ex situ addition of dopants. The N-doped porous carbon thus generated shows remarkable electrocatalytic activity towards ORR in the alkaline medium. The oxygen reduction on this material follows the desired 4-electron transfer mechanism involving the direct reduction pathway. Additionally, the synthesized carbon catalyst also exhibits good electrochemical stability and fuel tolerance. The results are also obtained and compared with the case of soybean flour having higher nitrogen content to highlight the significance of different parameters in the ORR catalyst performance.

}, issn = {1463-9076}, doi = {10.1039/c3cp55396e}, author = {Gokhale, Rohan and Unni, SreeKuttan M. and Puthusseri, Dhanya and Kurungot, Sreekumar and Ogale, Satishchandra} } @article { ISI:000336158700036, title = {Triple nanocomposites of CoMn2O4, Co3O4 and reduced graphene oxide for oxidation of aromatic alcohols}, journal = {Catalysis Science \& Technology}, volume = {4}, number = {6}, year = {2014}, month = {MAY}, pages = {1771-1778}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

A composite of reduced graphene oxide (RGO) with oxides of manganese and cobalt together was prepared by a solvothermal method. During synthesis, both the reduction of graphene oxide as well as the growth of nanorod shaped CoMn2O4 and Co3O4 occurred simultaneously having a crystallite size of similar to 8 nm calculated from X-ray diffraction (XRD). The as-obtained triple nanocomposite material designated as RGO-MnCoO exhibited excellent activity for the liquid phase aerobic oxidation of aromatic alcohols under base-free conditions selectively giving the corresponding aldehydes (\>85\%). RGO loading was varied in the range of 1-10\%, among which 1\% RGO-MnCoO showed maximum catalytic activity enhancement of 24\% as compared to the bare mixed oxide (MnCo-MO) for the oxidation of vanillyl alcohol. HR-TEM of RGO-MnCoO revealed that it was a composite material having uniform nanotubes of similar to 25 nm length and 6 nm diameter with a fringe pattern showing the (103) and (004) planes and lattice spaces of 0.26 nm and 0.22 nm, respectively, for the spinel CoMn2O4. The detailed studies on the morphology, size and composition of the as-prepared RGO-MnCoO nanocomposite by XRD, XPS, N-2-adsorption/desorption and O-2-TPD techniques were used to understand the role of RGO in the enhancement of catalytic activity for oxidation reaction.

}, issn = {2044-4753}, doi = {10.1039/c3cy01025b}, author = {Jha, Ajay and Mhamane, Dattakumar and Suryawanshi, Anil and Joshi, Sameer M. and Shaikh, Parvez and Biradar, Narayan S. and Ogale, Satishchandra and Rode, Chandrashekhar V.} } @article {46366, title = {Water electrolysis with a conducting carbon cloth: subthreshold hydrogen generation and superthreshold carbon quantum dot formation}, journal = {ChemSusChem}, volume = {7}, year = {2014}, month = {MAR}, pages = {883-889}, type = {Article}, abstract = {

A conducting carbon cloth, which has an interesting turbostratic microstructure and functional groups that are distinctly different from other ordered forms of carbon, such as graphite, graphene, and carbon nanotubes, was synthesized by a simple one-step pyrolysis of cellulose fabric. This turbostratic disorder and surface chemical functionalities had interesting consequences for water splitting and hydrogen generation when such a cloth was used as an electrode in the alkaline electrolysis process. Importantly, this work also gives a new twist to carbon-assisted electrolysis. During electrolysis, the active sites in the carbon cloth allow slow oxidation of its surface to transform the surface groups from COH to COOH and so forth at a voltage as low as 0.2V in a two-electrode system, along with platinum as the cathode, instead of 1.23V (plus overpotential), which is required for platinum, steel, or even graphite anodes. The quantity of subthreshold hydrogen evolved was 24mLcm(-2)h(-1) at 1V. Interestingly, at a superthreshold potential (\>1.23V+overpotential), another remarkable phenomenon was found. At such voltages, along with the high rate and quantity of hydrogen evolution, rapid exfoliation of the tiny nanoscale (5-7nm) units of carbon quantum dots (CQDs) are found in copious amounts due to an enhanced oxidation rate. These CQDs show bright-blue fluorescence under UV light.

}, keywords = {Carbon, electrolysis, Hydrogen, photoluminescence, quantum dots}, issn = {1864-5631}, doi = {10.1002/cssc.201300827}, author = {Biswal, Mandakini and Deshpande, Aparna and Kelkar, Sarika and Ogale, Satishchandra} } @article {46403, title = {ZnO(N)-Spiro-MeOTAD hybrid photodiode: an efficient self-powered fast-response UV (visible) photosensor}, journal = {Nanoscale}, volume = {6}, year = {2014}, month = {FEB}, pages = {503-513}, type = {Article}, abstract = {

Organic-inorganic hybrid photo-detectors with a self-sufficient mode of operation represent a research area of great current interest. In most efficient photodetectors and optoelectronic devices compound semiconductors containing toxic elements such as Cd, As, Te, S, Se etc. are used and these are also expensive. Hence there is also a rapidly growing interest in replacing these with environmentally friendly and earth-abundant materials. Herein, we report a facile solution-processed fabrication of a self-powered organic-inorganic hybrid photodetector using n-type oriented ZnO nanorods and p-type Spiro-MeOTAD semiconductor. ZnO is eco-friendly and earth-abundant, and Spiro-MeOTAD is nonhazardous. We show that the latter has far less toxicity than the toxic elements stated above. This visible blind UV photodetector shows high sensitivity (10(2)) and a UV/visible rejection ratio of 300. It also exhibits fast response times of tau(rise) similar to 200 mu s and tau(fall) similar to 950 mu s. Importantly, with a small modification of nitrogen incorporation in ZnO one can also realize a highly-sensitive self-powered visible light photodetector with at least 1000\% (or higher) improvements in quality factors (photocurrent/sensitivity/response time) as compared to previously reported organic-inorganic hybrid photo-detectors based on metal-chalcogenides (CdS-PANI or CuInSe2-P3HT). Interestingly, the broadband sensitivity of such N:ZnO-Spiro-MeOTAD photodiode enables sensing of low intensity (similar to 28 mu W cm(-2)) ambient white light with a high photocurrent density of 120 nA cm(-2) making it an efficient ambient white light detector.

}, issn = {2040-3364}, doi = {10.1039/c3nr04727j}, author = {Game, Onkar and Singh, Upendra and Kumari, Tanya and Banpurkar, Arun and Ogale, Satishchandra} } @article { ISI:000350222400077, title = {From micron to nano-curcumin by sophorolipid co-processing: highly enhanced bioavailability, fluorescence, and anti-cancer efficacy (vol 4, pg 60334, 2014)}, journal = {RSC Advances}, volume = {5}, number = {28}, year = {2015}, month = {FEB}, pages = {22075}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, issn = {2046-2069}, doi = {10.1039/c5ra90018b}, author = {Singh, Pradeep Kumar and Wani, Kirtee and Kaul-Ghanekar, Ruchika and Prabhune, Asmita and Ogale, Satishchandra} } @article { ISI:000353930700023, title = {Hybrid perovskite films by a new variant of pulsed excimer laser deposition: a room-temperature dry process}, journal = {Journal of Physical Chemistry C}, volume = {119}, number = {17}, year = {2015}, month = {APR}, pages = {9177-9185}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

A new variant of the classic pulsed laser deposition (PLD) process is introduced as a room-temperature dry process for the growth and stoichiometry control of hybrid perovskite films through the use of nonstoichiometric single target ablation and off-axis growth. Mixed halide hybrid perovskite films nominally represented by CH(3)NH(3)PbI(3-x)A(x) (A = Cl or F) are also grown and are shown to reveal interesting trends in the optical properties and photoresponse. Growth of good quality lead-free CH3NH3SnI3 films is also demonstrated, and the corresponding optical properties are presented. Finally, perovskite solar cells fabricated at room temperature (which makes the process adaptable to flexible substrates) are shown to yield a conversion efficiency of about 7.7\%.

}, issn = {1932-7447}, doi = {10.1021/acs.jpcc.5b02561}, author = {Bansode, Umesh P. and Naphade, Rounak and Game, Onkar S. and Agarkar, Shruti A. and Ogale, Satishchandra} } @article { ISI:000361501700023, title = {NiS1.97: a new efficient water oxidation catalyst for photoelectrochemical hydrogen generation}, journal = {ACS Applied Materials \& Interfaces}, volume = {7}, number = {36}, year = {2015}, month = {SEP}, pages = {20053-20060}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

NiS1.97, a sulfur-deficient dichalcogenide, in nanoscale form, is shown to be a unique and efficient photoelectrochemical (PEC) catalyst for H-2 generation by water splitting. Phase pure NiS1.97 nanomaterial is obtained by converting nickel oxide into sulfide by controlled sulfurization method, which is otherwise difficult to establish. The defect states (sulfur vacancies) in this material increase the carrier density and in turn lead to favorable band line-up with respect to redox potential of water, rendering it to be an effective photoelectrochemical catalyst. The material exhibits a remarkable PEC performance of 1.25 mA/cm(2) vs NHE at 0.68 V in neutral pH, which is almost 1000 times superior as compared with that of the stoichiometric phase of NiS2. The latter is well-known to be a cocatalyst but not as a primary PEC catalyst.

}, keywords = {dichlacogenide, Faradaic efficiency, Hydrogen generation, NiS1.97, nonstoichiometric, photoelectrochemical catalyst, sulfurization}, issn = {1944-8244}, doi = {10.1021/acsami.5b05077}, author = {Bhosale, Reshma and Kelkar, Sarika A. and Parte, Golu and Fernandes, Rohan and Kothari, Dushyant and Ogale, Satishchandra} } @article { ISI:000367561500004, title = {p-type NiO hybrid visible photodetector}, journal = {ACS Applied Materials \& Interfaces}, volume = {7}, number = {50}, year = {2015}, month = {DEC}, pages = {27597-27601}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

A novel hybrid visible-light photodetector was created using a planar p-type inorganic NiO layer in a junction with an organic electron acceptor layer. The effect of different oxygen pressures on formation of the NiO layer by pulsed laser deposition shows that higher pressure increases the charge carrier density of the film and lowers the dark current in the device. The addition of a monolayer of small molecules containing conjugated pi systems and carboxyl groups at the device interface was also investigated and with correct alignment of the energy levels improves the device performance with respect to the quantum efficiency, responsivity, and photogeneration. The thickness of the Organic layer was also optimized for the device, giving a responsivity of 1.54 X 10(-2) A W-1 in 460 nm light.

}, keywords = {nickel oxide, organic, oxygen vacancies, photodetector, pulsed laser deposition, surface modifier}, issn = {1944-8244}, doi = {10.1021/acsami.5b09291}, author = {Mallows, John and Planells, Miguel and Thakare, Vishal and Bhosale, Reshma and Ogale, Satishchandra and Robertson, Neil} } @article { ISI:000364314500010, title = {Pulsed laser-driven molecular self-assembly of cephalexin: aggregation-induced fluorescence and its utility as a mercury ion sensor}, journal = {Photochemistry and Photobiology}, volume = {91}, number = {6}, year = {2015}, month = {NOV}, pages = {1340-1347}, publisher = {WILEY-BLACKWELL}, address = {111 RIVER ST, HOBOKEN 07030-5774, NJ USA}, abstract = {

A fluorescent self-assembly of cephalexin is obtained by pulsed laser irradiation process. An intense fluorescence emission is found in the self-assembled form due to occurrence of a typical aggregation-induced emission in cephalexin molecules. It is observed that fluorescence quenching of the self-assembled fluorescent nanostructures occurs in the presence of extremely low Hg++ ions concentrations (10(-7) M) as compared to other heavy metal ions e.g. Ferrous (Fe++), Manganese (Mn++), Magnesium (Mg++), Cobalt (Co++), Nickel (Ni++) and Zinc (Zn++) at the same concentrations.

}, issn = {0031-8655}, doi = {10.1111/php.12526}, author = {Singh, Pradeep Kumar and Prabhune, Asmita and Ogale, Satishchandra} } @article { ISI:000357808500016, title = {Single-layer graphene-assembled 3D porous carbon composites with PVA and Fe3O4 nano-fillers: an interface-mediated superior dielectric and EMI shielding performance}, journal = {Physical Chemistry Chemical Physics}, volume = {17}, number = {28}, year = {2015}, month = {JUN}, pages = {18353-18363}, publisher = {ROYAL SOC CHEMISTRY}, address = {THOMAS GRAHAM HOUSE, SCIENCE PARK, MILTON RD, CAMBRIDGE CB4 0WF, CAMBS, ENGLAND}, abstract = {

In this study, a novel composite of Fe3O4 nanofiller-decorated single-layer graphene-assembled porous carbon (SLGAPC) with polyvinyl alcohol (PVA) having flexibility and a density of 0.75 g cm(-3) is explored for its dielectric and electromagnetic interference (EMI) response properties. The composite is prepared by the solution casting method and its constituents are optimized as 15 wt\% SLGAPC and 20 wt\% Fe3O4 through a novel solvent relaxation nuclear magnetic resonance experiment. The PVA-SLGAPC-Fe3O4 composite shows high dielectric permittivity in the range of 1 Hz-10 MHz, enhanced by a factor of 4 as compared to that of the PVA-SLGAPC composite, with a reduced loss by a factor of 2. The temperature dependent dielectric properties reveal the activation energy behaviour with reference to the glass transition temperature (80 degrees C) of PVA. The dielectric hysteresis with the temperature cycle reveals a remnant polarization. The enhanced dielectric properties are suggested to be the result of improvement in the localized polarization of the integrated interface system (Maxwell-Wagner-Sillars (MWS) polarization) formed by the uniform adsorption of Fe3O4 on the surface of SLGAPC conjugated with PVA. The EMI shielding property of the composite with a low thickness of 0.3 mm in the X-band (8.2-12.4 GHz) shows a very impressive shielding efficiency of similar to 15 dB and a specific shielding effectiveness of 20 dB (g cm(-3))(-1), indicating the promising character of this material for flexible EMI shielding applications.

}, issn = {1463-9076}, doi = {10.1039/c5cp02476e}, author = {Rao, B. V. Bhaskara and Yadav, Prasad and Aepuru, Radhamanohar and Panda, H. S. and Ogale, Satishchandra and Kale, S. N.} } @article { ISI:000379967000006, title = {3D interconnected porous graphene sheets loaded with cobalt oxide nanoparticles for lithium-ion battery anodes}, journal = {Energy Technology}, volume = {4}, number = {7}, year = {2016}, month = {JUL}, pages = {816-822}, publisher = {WILEY-V C H VERLAG GMBH}, address = {POSTFACH 101161, 69451 WEINHEIM, GERMANY}, abstract = {

Nanomaterials with high surface-to-volume ratio and tunable electronic and optical properties have expanded their use in variety of applications, especially energy conversion and storage. Here we report on the synthesis of a cobalt oxide (Co3O4)/3D-interconnected porous graphene (PG) nanocomposite by using a simple solvothermal route and its application as a Li-ion battery anode. Among the different compositions investigated, the composite PG-600 (with 50\% PG) showed a discharge capacity of 700mAhg(-1) at a current density of 500mAg(-1) and maintained 90\% retention after 80cycles. The high surface area of the 3DPG sheets helps the Co3O4 nanoparticles to form a uniform dispersion on the surfaces. The increased surface area (accessibility) and electrical conductivity of the composite result in significant enhancement in the capacity, cycling stability, and rate capability than the native Co3O4 phase.

}, keywords = {Cobalt oxide, Energy storage, graphene, lithium-ion batteries, Nanocomposites}, issn = {2194-4288}, doi = {10.1002/ente.201500497}, author = {Puthusseri, Dhanya and Aravindan, Vanchiappan and Madhavi, Srinivasan and Ogale, Satishchandra} } @article {42976, title = {3D Polyaniline architecture by concurrent inorganic and organic acid doping for superior and robust high rate supercapacitor performance}, journal = {Scientific Reports}, volume = {6}, year = {2016}, month = {FEB}, pages = {Article No. 21002}, doi = {10.1038/srep21002}, author = {Gawli, Yogesh and Banerjee, Abhik and Dhakras, Dipti and Deo, Meenal S. and Bulani, Dinesh and Wadgaonkar, Prakash P. and Shelke, Manjusha and Ogale, Satishchandra} } @article { ISI:000380052000012, title = {Highly stable laser-scribed flexible planar microsupercapacitor using mushroom derived carbon electrodes}, journal = {Advanced Materials Interfaces}, volume = {3}, number = {11}, year = {2016}, month = {JUN}, pages = {1600057}, publisher = {WILEY-BLACKWELL}, address = {111 RIVER ST, HOBOKEN 07030-5774, NJ USA}, abstract = {

A report is presented on the fabrication of all solid-state interdigitated flexible microsupercapacitor using ultrafast and highly scalable laser scribing technique, using highly mesoporous carbon synthesized from biomass (mushroom) with hydrothermal preprocessing. The specific protocol used for carbon synthesis renders some unique property features to the material (surface area of 2604 m(2) g(-1) with hierarchical pore size distribution) in the context of supercapacitor electrode application. A polyvinyl alcohol (PVA)-H2SO4 gel electrolyte is used for electrochemical measurements. The microsupercapacitor shows high cyclic stability up to 15000 cycles. Moreover it shows nearly 90\% stability after 1000 bending cycles at 60 degrees angle. It also retains its performance even under 120 degrees bending condition. This work represents a facile and fast technique for microscaled device fabrication that can be easily commercialized. Moreover, the mushroom-derived carbon used to make the electrodes holds great promise in context of the stability and flexibility of flexible supercapacitors.

}, issn = {2196-7350}, doi = {10.1002/admi.201600057}, author = {Yadav, Poonam and Basu, Aniruddha and Suryawanshi, Anil and Game, Onkar S. and Ogale, Satishchandra} } @article {43573, title = {High-performance organic-inorganic hybrid piezo-nanogenerator via interface enhancedpolarization effects for self-powered electronic systems}, journal = {Advanced Materials Interfaces}, volume = {3}, year = {2016}, month = {OCT}, pages = {Article Number: 1600492}, abstract = {An electrospun fi ber based wearable organic-inorganic hybrid piezonanogenerator compose of suitably engineered P(VDF-TrFE) and BaTiO3 nanostructures is reported. In the case of the device with an electrospun mat of piezoelectric beta-phase P(VDF-TrFE) and BaTiO3 nanoparticulates fi lled in the interfi ber open spaces, a power density of 16 mu W cm(-2) is realized at an applied impact of 0.02 MPa (which essentially corresponds to the thumb pressure). A similar device, with BaTiO 3 additionally embedded in the P(VDF-TrFE) fi bers during their formation, renders a signifi cantly higher peak power density of 28 mu W cm(-2) with instantaneous power density of approximate to 8.8 mu W cm(-2) at the same touch pressure. This performance is attributed to the high density of interfaces in such a device and the corresponding enhancement in the dielectric response. It is demonstrated that the power generated from such a hybrid device structure can be used for small scale applications such as charging a mobile phone.}, doi = {10.1002/admi.201600492}, author = {Dhakras, Dipti and Ogale, Satishchandra} } @article { ISI:000368563000102, title = {Hybrid perovskite quantum nanostructures synthesized by electrospray antisolvent-solvent extraction and intercalation}, journal = {ACS Applied Materials \& Interfaces}, volume = {8}, number = {1}, year = {2016}, month = {JAN}, pages = {854-861}, publisher = {AMER CHEMICAL SOC}, address = {1155 16TH ST, NW, WASHINGTON, DC 20036 USA}, abstract = {

Perovskites based on organometal lead halides have attracted great deal of scientific attention recently in the context of solar cells and optoelectronic devices due to their unique and tunable electronic and optical properties. Herein, we show that the use of electrospray technique in conjunction with the antisolventsolvent extraction leads to novel low-dimensional quantum structures (especially 2-D nanosheets) of CH3NH3PbI3- and CH3NH3PbBr3-based layered perovskites with unusual luminescence properties. We also show that the optical bandgaps and emission characteristics of these colloidal nanomaterials can be tuned over a broad range of visible spectral region by compositional tailoring of mixed-halide (I- and Br-based) perovskites.

}, keywords = {2D nanostructure systems, antisolvent-solvent extraction, bandgap tuning, electrospray, nanosheets, perovskite, quantum dots}, issn = {1944-8244}, doi = {10.1021/acsami.5b10208}, author = {Naphade, Rounak and Nagane, Satyawan and Shanker, G. Shiva and Fernandes, Rohan and Kothari, Dushyant and Zhou, Yuanyuan and Padture, Nitin P. and Ogale, Satishchandra} } @article {43595, title = {Minute-made activated porous carbon from agro-waste for Li-ion battery anode using a low power microwave oven}, journal = {Electrochimica ACTA}, volume = {212}, year = {2016}, month = {SEP}, pages = {535-544}, abstract = {We demonstrate a very simple, cost-effective and superfast process for making Li-ion battery (LIB) anode grade carbon from agro-waste in the form of sugarcane bagasse using a low power microwave system. Activation of this bagasse derived carbon is carefully optimized by using various weight ratios of KOH to obtain the desired properties of functional carbon in terms of porosity and electrical conductivity. Low equivalent series resistance (ESR), low charge transfer resistance with good electrical conductivity, and optimum porosity for efficient ion diffusion make this carbon a good candidate for Li-ion battery anode material rendering a reversible capacity of 757 mAhg (1) at a current density of 100 mAg (1) and a good cycling performance at high current rates. (C) 2016 Elsevier Ltd. All rights reserved.}, doi = {10.1016/j.electacta.2016.07.011}, author = {Agarkar, Shruti and Yadav, Poonam and Fernandes, Rohan and Kothari, Dushyant and Suryawanshi, Anil and Ogale, Satishchandra} } @article {43823, title = {Low-dimensional hybrid perovskites as high performance anodes for alkali-ion batteries}, journal = {Journal of Materials Chemistry A}, volume = {5}, year = {2017}, month = {SEP}, chapter = {18634-18642}, abstract = {

State-of-the-art Li (or Na) ion batteries work by insertion/extraction of the alkali metal ions into a porous electrode material, where the overall capacity is strongly dependent on the accessibility of the host material interior to the ions. On the other hand, the performance stability depends on various factors governed by the specific constitution of the electrode. Here we show that molecularly engineered low-dimensional hybrid perovskites can work as excellent anode materials for alkali-ion batteries. We measure a high reversible capacity of 646 mA h g(-1) at 100 mA g(-1) with good stability tested up to 250 cycles for the benzidine mediated lead iodide based 1D system. An ex situ analysis of the electrodes reveals that the storage primarily occurs via the Li-x(or Na-x)Pb alloying/de-alloying process. We anticipate that these results open a new direction for the use of low-dimensional hybrid perovskites for energy storage applications.

}, keywords = {Generation, Inorganic-Organic Hybrid, Lead Iodide, lithiation-intramolecular electrophilic reaction, Na-Air Battery, Negative Electrodes, Organometal Halide perovskites, PB, Sequential Deposition, Solar-cells}, issn = {2050-7488}, doi = {10.1039/c7ta04529h}, author = {Tathavadekar, Mukta and Krishnamurthy, Shrreya and Banerjee, Aparna and Nagane, Satyawan and Gawli, Yogesh and Suryawanshi, Anil and Bhat, Suresh and Puthusseri, Dhanya and Mohite, Aditya D. and Ogale, Satishchandra} } @article {43807, title = {Nanotubular hard carbon derived from renewable natural seed gel for high performance sodium-ion battery anode}, journal = {Chemistryselect}, volume = {2}, year = {2017}, month = {AUG}, pages = {6909-6915}, type = {Article}, abstract = {

Electrical energy storage devices such as batteries and supercapacitors are perhaps the most researched topic today in view of its critical implications for the successful implementations of various renewable energy harvesting initiatives. Amongst the various battery systems being currently examined, the Li-battery continues to be a main player, but the Na-ion battery has been attracting significant attention lately due to the concerns about the limited reserves and high cost of Li. Hard carbon is recognized to be a good anode material for Na-battery. In this work we present a novel approach to synthesize such hard carbon from a natural gel derived from the commonly used Basil seeds (Osimum Basilicum) which swell 30 times their weight by absorbing water. The hard carbon obtained by pyrolysis of the freeze-dried mucilage possesses sheet-like and tubular morphology with decorated surface defects attributed to the presence of oxygen functionalities. This hard carbon shows a good reversible capacity of 195 mAh g(-1) at 0.1A g(-1) with an impressive approximate to 91\% retention of initial capacity after 300 cycles and sustains high current densities with not much change in capacity value.

}, doi = {10.1002/slct.201701123}, author = {Sharma, Neha and Gawli, Yogesh and Ahmad, Absar and Muhammed, Musthafa and Ogale, Satishchandra} } @article {42969, title = {Phenothiazine-based D-A-π-A dyes for highly efficient dye sensitized solar cells: effect of internal acceptor and non-conjugated π-spacer on device performance}, journal = {ChemPlusChem}, volume = {82}, year = {2017}, month = {FEB}, pages = {280-286}, abstract = {Three new D-A-pi-A metal-free organic dyes based on phenothiazine as a donor (D) and non-conjugated pi-spacer were designed and synthesized. The incorporation of different {\textquoteright}internal acceptors{\textquoteright} (electron traps) such as benzothiadiazole (BTD), benzotriazole (BTA), and pyridine were shown to allow systematic tuning of the energy levels and the photophysical properties. The AI-1 dye showed lower electronic disorder compared with the other two dyes. The efficiencies achieved with AI-1, AI-2, and AI-3 dyes were 8.5\% (J(sc) = 15.42 mA cm(-2), V-oc = 0.78 V, FF = 68\%), 7\% (J(sc) = 12.8 mA cm(-2), V-oc = 0.78 V, FF = 68\%) and 6.7\% (J(sc) = 11.57 mA cm(-2), V-oc = 0.82 V, FF = 68.26 \%), respectively. The incorporation of non-conjugated phenothiazine as a p-spacer in D-A-pi-A dyes showed remarkable enhancement in the photovoltaic performance of dye-sensitized solar cell (DSSC) devices. The sealed DSSC devices with iodide/tri-iodide (I-/I-3(-) @)based liquid electrolyte showed promising stability under ambient conditions.}, doi = {10.1002/cplu.201600492}, author = {Nagane, Satyawan and Ichake, Amol and Agrawal, Ishita and Sadhanala, Aditya and Friend, Richard H. and Ogale, Satishchandra and Wadgaonkar, Prakash P.} } @article {44166, title = {Synthetic manipulation of hybrid perovskite systems in search of new and enhanced functionalities}, journal = {ChemSusChem}, volume = {10}, year = {2017}, month = {OCT}, pages = {3722-3739}, type = {Article}, abstract = {Over the past few years the organic-inorganic hybrid perovskite systems have emerged as a promising class of materials for photovoltaic and electroluminescent thin-film device applications, in view of their unique set of tunable optoelectronic properties. Importantly, these materials can be easily solution-processed at low temperatures and as such are amenable to facile molecular engineering. Thus, a variety of low-dimensional forms and quantum structures of these materials can be obtained through strategic synthetic manipulations through small molecule incorporation or molecular ion doping. In this Minireview, we specifically focus on these approaches and outline the possibilities of utilizing these for enhanced functionalities and newer application domains.}, doi = {10.1002/cssc.201701093}, author = {Naphade, Rounak and Nagane, Satyawan and Bansode, Umesh and Tathavadekar, Mukta and Sadhanala, Aditya and Ogale, Satishchandra} } @article {44481, title = {G-C3N4/NiAl-LDH 2D/2D hybrid heterojunction for high-performance photocatalytic reduction ofco2 into renewable fuels}, journal = {ACS Applied Materials \& Interfaces}, volume = {10}, year = {2018}, month = {JAN}, pages = {2667-2678}, type = {Article }, abstract = {2D/2D interface heterostructures of g-C3N4 and NiAl-LDH are synthesized utilizing strong electrostatic interactions between positively charged 2D NiAl-LDH sheets and negatively charged 2D g-C3N4 nanosheets. This new 2D/2D interface heterojunction showed remarkable performance for photocatalytic CO, reduction to produce renewable fuels such as CO and H-2 under visible-light irradiation, far superior to that of either single phase g-C3N4 or NiAl-LDH nanosheets. The enhancement of photocatalytic activity could be attributed mainly to the excellent interfacial contact at the heterojunction of gC(3)N(4)/NiAl-LDH, which subsequently results in suppressed recombination, and improved transfer and separation of photogenerated charge carriers. In addition, the optimal g-C3N4/NiAl-LDH nanocomposite possessed high photostability after successive experimental runs with no obvious change in the production of CO from CO, reduction. Our findings regarding the design, fabrication and photophysical properties of 2D/2D heterostructure systems may find use in other photocatalytic applications including H-2 production and water purification.}, doi = {10.1021/acsami.7b18835}, author = {Tonda, Surendar and Kumar, Santosh and Bhardwaj, Monika and Yadav, Poonam and Ogale, Satishchandra} } @article {44493, title = {High and reversible lithium ion storage in self-exfoliated triazole-triformyl phloroglucinol-basedcovalent organic nanosheets}, journal = {Advanced Energy Materials}, volume = {8}, year = {2018}, month = {MAR}, pages = {Article Number: 1702170}, abstract = {Covalent organic framework (COF) can grow into self-exfoliated nanosheets. Their graphene/graphite resembling microtexture and nanostructure suits electrochemical applications. Here, covalent organic nanosheets (CON) with nanopores lined with triazole and phloroglucinol units, neither of which binds lithium strongly, and its potential as an anode in Li-ion battery are presented. Their fibrous texture enables facile amalgamation as a coin-cell anode, which exhibits exceptionally high specific capacity of approximate to 720 mA h g(-1) (@100 mA g(-1)). Its capacity is retained even after 1000 cycles. Increasing the current density from 100 mA g(-1) to 1 A g(-1) causes the specific capacity to drop only by 20\%, which is the lowest among all high-performing anodic COFs. The majority of the lithium insertion follows an ultrafast diffusion-controlled intercalation (diffusion coefficient, D-Li(+) = 5.48 x 10(-11) cm(2) s(-1)). The absence of strong Li-framework bonds in the density functional theory (DFT) optimized structure supports this reversible intercalation. The discrete monomer of the CON shows a specific capacity of only 140 mA h g(-1) @50 mA g(-1) and no sign of lithium intercalation reveals the crucial role played by the polymeric structure of the CON in this intercalation-assisted conductivity. The potentials mapped using DFT suggest a substantial electronic driving-force for the lithium intercalation. The findings underscore the potential of the designer CON as anode material for Li-ion batteries.}, doi = {10.1002/aenm.201702170}, author = {Haldar, Sattwick and Roy, Kingshuk and Nandi, Shyamapada and Chakraborty, Debanjan and Puthusseri, Dhanya and Gawli, Yogesh and Ogale, Satishchandra and Vaidhyanathan, Ramanathan} } @article {46197, title = {Direct Z-scheme g-C3N4/FeWO4 nanocomposite for enhanced and selective photocatalytic CO2 reduction under visible light}, journal = {ACS Applied Materials \& Interfaces}, volume = {11}, year = {2019}, month = {FEB }, pages = {6174-6183}, type = {Article}, abstract = {

Photocatalytic reduction of CO2 to renewable solar fuels is considered to be a promising strategy to simultaneously solve both global warming and energy crises. However, development of a superior photocatalytic system with high product selectivity for CO2 reduction under solar light is the prime requisite. Herein, a series of nature-inspired Z-scheme g C3N4/FeWO4 composites are prepared for higher performance and selective CO2 reduction to CO as solar fuel under solar light. The novel direct Z-scheme coupling of the visible light-active FeWO4 nanoparticles with C3N4 nanosheets is seen to exhibit excellent performance for CO production with a rate of 6 mu mol/g/h at an ambient temperature, almost 6 times higher compared to pristine C3N4 and 15 times higher than pristine FeWO4. More importantly, selectivity for CO is 100\% over other carbon products from CO, reduction and more than 90\% over. H-2 products from water splitting. Our results clearly demonstrate that the staggered band structure between FeWO4 and C3N4 reflecting the nature-inspired Z-scheme system not only favors superior spatial separation of the electron hole pair in g-C3N4/FeWO4 but also shows good reusability. The present work provides unprecedented insights for constructing the direct Z-scheme by mimicking the nature for high performance and selective photocatalytic CO2 reduction into solar fuels under solar light.

}, keywords = {C3N4, CO2 reduction, FeWO4, Photocatalysis, solar fuels, Z-scheme}, issn = {1944-8244}, doi = {10.1021/acsami.8b22434}, author = {Bhosale, Reshma and Jain, Srashti and Vinod, Chathakudath Prabhakaran and Kumar, Santosh and Ogale, Satishchandra} } @article {46881, title = {Room temperature processed in-situ carbon-coated vanadium carbide (VC@C) as a high capacity robust Li/Na battery anode material}, journal = {Carbon}, volume = {161}, year = {2020}, month = {MAY}, pages = {108-116}, type = {Article}, abstract = {

3D carbide systems with their robust physical and mechanical properties have always attracted multiple application interests. In this report, we have synthesized a three-dimensional in-situ carbon coated cubic carbide, Vanadium Carbide (VC@C), by a very simple, scalable and cost-effective room temperature mechano-chemical ball-milling procedure and researched its promise as effective anode material for Li and Na ion batteries. We have demonstrated that VC@C shows an impressive initial discharge/lithiation capacity of 1165 mAh g(-1) with a high reversible capacity of 640 mAh g(-1) after 100 charge-discharge cycles at an applied current density of 0.1 A g(-1). We have also found that this material renders a very promising rate performance with significantly low capacity drop after exposing it to variable current densities ranging from 0.05 A g(-1) to 2 A g(-1) with an excellent stability up to 1000 cycles owing to its structural robustness, as verified by post-cycling characterizations. A Li-ion full cell study using LiCoO2 as cathode also showed excellent promise in terms of practical application demonstrating a reversible capacity of 95 mAh g(-1) after 100 cycles. Even for Na insertion/de-insertion VC@C shows a clear promise in terms of capacity, cyclic stability and rate performance. (C) 2020 Elsevier Ltd. All rights reserved.

}, keywords = {3D carbide, In-situ synthesis, Li-ion battery, Post cycling characterization, Room temperature ball milling, Williamson-Hall analysis}, issn = {0008-6223}, doi = {10.1016/j.carbon.2020.01.057}, author = {Mahajan, Mani and Roy, Kingshuk and Parmar, Swati and Singla, Gourav and Pandey, O. P. and Singh, K. and Vaidhyanathan, Ramanathan and Ogale, Satishchandra} } @article {47742, title = {Organic-inorganic perovskitoid with zwitterion cysteamine linker and its crystal-crystal transformation to ruddlesden-popper phase}, journal = {Angewandte Chemie-International Edition}, volume = {60}, year = {2021}, month = {AUG }, pages = {18750-18760}, type = {Article}, abstract = {We demonstrate synthesis of a new low-D hybrid perovskitoid (a perovskite-like hybrid halide structure, yellow crystals, P21/n space group) using zwitterion cysteamine (2-aminoethanethiol) linker, and its remarkable molecular diffusion-controlled crystal-to-crystal transformation to Ruddlesden-Popper phase (Red crystals, Pnma space group). Our stable intermediate perovskitoid distinctly differs from all previous reports by way of a unique staggered arrangement of holes in the puckered 2D configuration with a face-sharing connection between the corrugated-1D double chains. The PL intensity for the yellow phase is 5 orders higher as compared to the red phase and the corresponding average lifetime is also fairly long (143 ns). First principles DFT calculations conform very well with the experimental band gap data. We demonstrate applicability of the new perovskitoid yellow phase as an excellent active layer in a self-powered photodetector and for selective detection of Ni2+ via On-Off-On photoluminescence (PL) based on its composite with few-layer black phosphorous.}, keywords = {Crystal growth, organic-inorganic hybrid composites, perovskite phases, photodetectors, zwitterions}, issn = {1433-7851}, doi = {10.1002/anie.202105918}, author = {Kour, Prachi and Reddy, Mallu Chenna and Pal, Shiv and Sidhik, Siraj and Das, Tisita and Pandey, Padmini and Mukherjee, Shatabdi Porel and Chakraborty, Sudip and Mohite, Aditya D. and Ogale, Satishchandra} } @article {47752, title = {Resistive switching in HfO2-x/La0.67Sr0.33MnO3 heterostructures: an intriguing case of low H-field susceptibility of an E-field controlled active interface}, journal = {ACS Applied Materials \& Interfaces}, volume = {13}, year = {2021}, month = {NOV }, pages = {54133-54142}, type = {Article}, abstract = {High-performance nonvolatile resistive random access memories (ReRAMs) and their small stimuli control are of immense interest for high-speed computation and big-data processing in the emerging Internet of Things (IoT) arena. Here, we examine the resistive switching (RS) behavior in growth-controlled HfO2/La0.67Sr0.33MnO3 (LSMO) heterostructures and their tunability in a low magnetic field. It is demonstrated that oxygen-deficient HfO2 films show bipolar switching with a high on/off ratio, stable retention, as well as good endurance owing to the orthorhombic-rich phase constitution and charge (de)trapping-enabled Schottky-type conduction. Most importantly, we have demonstrated that RS can be tuned by a very low externally applied magnetic field (similar to 0-30 mT). Remarkably, application of a magnetic field of 30 mT causes RS to be fully quenched and frozen in the high resistive state (HRS) even after the removal of the magnetic field. However, the quenched state could be resurrected by applying a higher bias voltage than the one for initial switching. This is argued to be a consequence of the electronically and ionically {\textquoteleft}{\textquoteleft}active{\textquoteright}{\textquoteright} nature of the HfO2-x/LSMO interface on both sides and its susceptibility to the electric and low magnetic field effects. This result could pave the way for new designs of interface-engineered high-performance oxitronic ReRAM devices.}, keywords = {charge trapping-detrapping, low external magnetic field, oxide-oxide interface, pulsed laser deposition, resistive switching, Schottky barrier}, issn = {1944-8244}, doi = {10.1021/acsami.1c15082}, author = {Antad, Vivek and Shaikh, Parvez A. and Biswas, Abhijit and Rajput, Shatruhan Singh and Deo, Shrinivas and Shelke, V, Manjusha and Patil, Shivprasad and Ogale, Satishchandra} } @article {48803, title = {Mitigating dendrite formation on a Zn electrode in aqueous zinc chloride by the competitive surface chemistry of an imidazole additive}, journal = {ACS Applied Materials and Interfaces}, volume = {15}, year = {2023}, month = {MAY}, pages = {23093-23103}, type = {Article}, abstract = {

Electrochemical energy storage systems are critical in several ways for a smooth transition from nonrenewable to renewable energy sources. Zn-based batteries are one of the promising alternatives to the existing state-of-the-art Li-ion battery technology, since Li-ion batteries pose significant drawbacks in terms of safety and cost-effectiveness. Zn (with a reduction potential of -0.76 V vs SHE) has a significantly higher theoretical volumetric capacity (5851 mAh/cm3) than Li (2061 mAh/cm3), and it is certainly far less expensive, safer, and more earth-abundant. The formation of dendrites, hydrogen evolution, and the formation of a ZnO passivation layer on the Zn anode are the primary challenges in the development and deployment of rechargeable zinc batteries. In this work, we examine the role of imidazole as an electrolyte additive in 2 M ZnCl2 to prevent dendrite formation during zinc electrodeposition via experimental (kinetics and imaging) and theoretical density functional theory (DFT) studies. To characterize the efficacy and to identify the appropriate concentration of imidazole, linear sweep voltammetry (LSV) and chronoamperometry (CA) are performed with in situ monitoring of the electrodeposited zinc. The addition of 0.025 wt \% imidazole to 2 M ZnCl2 increases the cycle life of Zn-symmetric cells cycled at 1 mA/cm2 for 60 min of plating and stripping dramatically from 90 to 240 h. A higher value of the nucleation overpotential is noted in the presence of imidazole, which suggests that imidazole is adsorbed at a competitively faster rate on the surface of zinc, thereby suppressing the zinc electrodeposition kinetics and the formation. X-ray tomography reveals that a short circuit caused by dendrite formation is the main plausible failure mechanism of Zn symmetric cells. It is observed that the electrodeposition of zinc is more homogeneous in the presence of imidazole, and its presence in the electrolyte also inhibits the production of a passivating coating (ZnO) on the Zn surface, thereby preventing corrosion. DFT calculations conform well with the stated experimental observations.

}, keywords = {dendrite, Density functional theory, exchange current density, Imidazole, X-ray computed tomography, zinc metal electrodeposition}, issn = {1944-8244}, doi = {10.1021/acsami.3c01310}, author = {Rana, Ashutosh and Thakare, Anup and Kumar, Nikhil and Mukherjee, Buddhadev and Torris, Arun and Das, Bidisa and Ogale, Satishchandra and Banerjee, Abhik} }